QZGBL4001-001BL4000 2.4GHz WLAN ODU

-2- Copyright Copyright © 2004 all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permission of the supplier. About This Manual The purpose of this manual is for the setup of the 11Mbps Wireless LAN ODU. This manual, revised as version 4.0.3 in 2004, includes procedures assisting you in avoiding unforeseen problems. Technical Support If you have difficulty resolving the problem while installing or using the Wireless LAN ODU, please contact the supplier for support. -3- FCC Notice FCC Certified Declaration: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Reminder: To comply with FCC part 15 rules, the ODU must only be used as a system as FCC certified. The system must also be professionally installed to ensure compliance with the Part 15 certification. It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed in where FCC rules apply. Further, according to FCC Part 15 regulations, Section 15.247(b)(3)(iii), the installer must ensure that the high-gain directional antenna used in this system is used exclusively for fixed, point-to-point operations and that multiple co-located intentional radiators transmitting the same information are not used. For further information, please see Appendix B. Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 2 meters from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. -4- Table of Contents Chapter 1 Introduction..........................................................................5 1-1 Features and Benefits.............................................................................5 1-2 Applications..........................................................................................6 1-3 System Configurations...........................................................................7 Chapter 2 Hardware Installation.........................................................8 Chapter 2 Hardware Installation.........................................................9 2-1 Product Kit............................................................................................9 2-2 System Requirements.............................................................................9 2-3 Mechanical Description.......................................................................10 2-4 Hardware Installation..........................................................................11 Chapter 3 Configuring the ODU........................................................12 3-1 Configuration......................................................................................12 3-2 Using the Web Management.................................................................25 3-3 Using the Telnet...................................................................................29 Appendix A: Channels................................................................................36 Appendix B: FCC Certified Systems...........................................................37 Appendix C: Troubleshooting.....................................................................38 -5- Chapter 1 Introduction The Outdoor wireless LAN device – 11Mbps Wireless Outdoor Unit, are specially designed for Point-to-Point and Point-to-Multipoint applications, offering long distance connections between buildings at a speed of up to 11Mbps. Fully compliant with IEEE802.11b standard, the Outdoor Unit (ODU) provides powerful features such as the Windows-based configuration utility, MAC address filtering, WEP security, 802.1x authentication and more. 1-1 Features and Benefits n Creates a Point-to-Point connection linking two LANs, using 2 Indoor Units or Indoor and Outdoor total solutions. n Creates a Point-to-Multipoint system using three or more Indoor Units or Indoor and Outdoor total solutions. n Detachable antenna allows you for the use of external high gain antenna. n With a data rate of 11Mbps and 5.5Mbps, the system is faster than an E1/T1 data link. n Features 11Mbps data rate by incorporating Direct Sequence Spread Spectrum technology. n Fully IEEE 802.11b compatible. Allow inter-operation among multiple vendors. n Technique operating in the unlicensed 2.4GHz ISM band. n Seamless roaming within the 802.11 & 802.11b wireless LAN infrastructure. n Provides user authentication to enforce tight security. n MAC address Access Control. n Bandwidth control n Advanced Security — 802.1x authentication (EAP) n Provides Window-based configuration utility. n Waterproof housing -6- 1-2 Applications The 11Mbps Wireless LAN ODU offers a fast, reliable, cost-effective solution for wireless client access to the network in applications like these: 1. Remote Access to Corporate Network Information E-mail, file transfer and terminal emulation. 2. Difficult-to-Wire Environments Historical or old buildings, asbestos installations, and open area where wiring is difficult to deploy. 3. Frequently Changing Environments Retailers, manufacturers and those who frequently rearrange the workplace and change location. 4. Temporary LANs for Special Pr…

Text truncated - open the document above for the full version.

Federal Communications Commission FCC ID: QZGBL4001-001 Dear Sir: This is to request confidentiality on information submitted for above application. We would like to request confidentiality on some exhibits we submitted for above original application for the reason of trade secret. If those exhibits are available for public inspection, any person who once gets the information contained in those exhibits will be able to design and to make the same products very easily. This is a very serious problem and huge loss for us, because we did invest so much on it. Please be not made the Exhibit Types listed below routinely available for public inspection: Block Diagram and Schematics. By: By: Steve Chen (Signature) (Printed) Title : Enginer Applicant : K-Best Technology Inc. Address : 2Fl, -1, No. 185, Ko Wang Rd., Kau Yuan Tsun, Lung Tan Hsiang, Tao Yuan Hsien, Taiwan Tel : +886-3-4072360 Fax: +886-3-4072377 Date : 12/14/2004

Federal Communications Commission Dear Sir: We, the undersigned, hereby authorize ELECTRONICS TESTING CENTER, TAIWAN to act on our behalf in all matters relating to application forBL4000 2.4GHz WLAN ODU ( Model : BL4001, FCC ID : QZGBL4001-001 )authorization, including the signing of all documents relating to these matters. Any and all acts carried out by ELECTRONICS TESTING CENTER, TAIWAN on our behalf shall have the same effect as acts of our own. The applicant certifies that in the case of an individual applicant ( e.g., corporation ), no party to the applicant is subject to a denial of federal benefits, that includes FCC benefits, pursuant to section 5301 of the Anti-drug abuse Act of 1988, 21 U.S.C. 862. For a definition of a “party” for these purposes See 47 C.F.R. 1.2002(b). By: By: Steve Chen (Signature) (Printed) Title : Enginer Applicant : K-Best Technology Inc. Address : 2Fl, -1, No. 185, Ko Wang Rd., Kau Yuan Tsun, Lung Tan Hsiang, Tao Yuan Hsien, Taiwan Tel : +886-3-4072360 Fax: +886-3-4072377 Date : 12/14/2004

1 Helen Zhao Subject:FW: K-Best Technology Inc., FCC ID: QZGBL4001-001, Assessment NO.: AN04T4432, Notice#1 Exhibit-B-Internal_P hotos_revi... Exhibit-D-ID_Label_ revised.pdf... Exhibit-F-Setup_Ph otos_revised... Exhibit-H-External_ Photos_revi... Exhibit-I-Authorizati on_revise... MPE evaluation QZGBL4001-001.p... From: SS Sent: Tuesday, January 18, 2005 3:38 AM To: Helen Zhao Subject: Fw: K-Best Technology Inc., FCC ID: QZGBL4001-001, Assessment NO.: AN04T4432, Notice#1 > Dear Helen, > > Replying your questions, > > #1 Please refer to revised product photos. The photos of AC/DC power adapter > are added. > #2 The photos of CR filter are misleading. The whole system consist of ODU, > PoE, antenna and AC/DC power adapter. Please refer to page 1 of block > diagrams and the revised product photos. > #3 Please refer to revised FCC ID label format information. > #4 The user manual has been revised. In Appendix B (page 37) the FCC ID and > its related models are indicated. > #5 Please refer to revised test report. The calibration date has been > updated. > #6 Please refer to revised test report. > #7 Please refer to revised test report. The correct data plots are provided. > #8 Please find attached MPE evaluations. > #9 Please find attached revised authorization letter. > > Best regards, > > S. S. Liou > Engineer / EMC Dept. II > Electronics Testing Center, Taiwan > Subject: K-Best Technology Inc., FCC ID: QZGBL4001-001, Assessment NO.: > AN04T4432, Notice#1 > > Question #: From the external photos, the system consists of ODU, CR filter > and DC adapter. Actually the DC adapter is a POE interface, please provide > photos for the real AC Power adapter. > > Question #2: The external photos show CR filter, but it does not show on > Test setup photos. Neither operation description nor user manual does > mention it. Please explain how it works with the ODU. > > Question #3: The proposed FCC ID label format shows a FCC ID that differs 2 > from the Form 731. Please revise the FCC ID label format. > > Question #4: The user manual includes BL4001, BL4002 and BL4003. Since there > are two different FCC IDs, each with diffrent power setting, if you want to > list two FCC IDs, please indicate clearly FCC ID with associated technical > specification. > > Question #5: Since some tests were recently done. Please update calibration > date in the test report. > > Question #6: Regarding 18dBi panel antenna, there are several areas it was > wrongly referred to. Please update Page 26, 34, 40, 45 in the test report, > and page 4 in the setup photos. > > Question #7: Page 82 of the test plots shows the wrong RBW setting was used > during the low bandedge testing. Please correct. > > Question #8: Please provide MPE calculation. > > Question #9: The authorization letter is actually identical to the > confidentiality letter. Please resubmit authorization letter. > > Best Regards, > Helen Zhao > > The items indicated above must be submitted before processing can continue > on the above referenced application. Failure to provide the requested > information within 30 days of the original e-mail date may result in > application dismissal and forfeiture of the filing fee. Also, please note > that partial responses increase processing time and should not be submitted. > Any questions about the content of this correspondence should be directed to > the e-mail address listed below the name of the sender. > >

ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Top View of EUT Side View of EUT ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Side View of EUT Side View of EUT ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Bottom View of EUT ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Top View of Wireless LAN Card Bottom View of Wireless LAN Card ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Top View of DC Adaptor Bottom View of DC Adaptor ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Side View of DC Adaptor Side View of DC Adaptor ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Side View of DC Adaptor ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Top View of AC/DC Power Adaptor Bottom View of AC/DC Power Adaptor

This statement will be placed in User’s Manual: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 2.4GHz 0.1W WLAN ODU Model No.:BL4001 FCC ID:QZGBL4001- 001 S/N:24400103440001

ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Internal View of EUT Internal View of EUT ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Internal View of EUT Internal View of EUT ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Internal View of Wireless LAN Card Component View of Wireless LAN Card ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Component View of Wireless LAN Card Solder View of Wireless LAN Card ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Component View of Main PCB Solder View of Main PCB ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Component View of LED’s PCB Solder View of LED’s PCB ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Component View of DC to DC PCB Solder View of DC to DC PCB ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Internal View of DC Adaptor ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Component View of DC Adaptor’s PCB Solder View of DC Adaptor’s PCB ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Internal View of AC/DC Power Adaptor Component View of AC/DC Power Adaptor ETC Report No. : ET93R-03-099-01 FCC ID.:QZGBL4001-001 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Solder View of AC/DC Power Adaptor

SYS1148 (13~35W) 50*103*32/mm INPUT: 100-240VAc,50-60Hz,1.0A,60-70VA O/P: +12Vdc,2.0A,30W ΩΩΩ ≤≥ ≤ 1.4 ≤ 1.4 360°360° 360° 90°6° 6° °°° °°° ΩΩ ≤≤ 90°20° 7°20° °° °° ΩΩ ≤≤ 10°9° 12°11° °° °°

FCC ID: QZGBL4001-001 RF Exposure Evaluation of E.U.T. : BL4000 2.4GHz WLAN ODU FCC ID. : QZGBL4001-001 MODEL : BL4001 for APPLICANT : K-Best Technology Inc. ADDRESS : 2F1, -1, No. 185, Ko Wang Rd., Kau Yuan Tsun, Lung Tan Hsiang, Tao Yuan Hsien, Taiwan Prepared by ELECTRONICS TESTING CENTER, TAIWAN NO. 34, LIN 5, DING FU TSUN, LINKOU HSIANG, TAIPEI HSIEN, TAIWAN, R.O.C. Tel:(02)26023052 Fax:(02)26010910 http://www.etc.org.tw ; e-mail: [email protected] Report Number : ET93R-03-099-01 FCC ID: QZGBL4001-001 Product Information: Type of EUT: BL4000 2.4GHz WLAN ODU FCC ID: QZGBL4001-001 Manufacturer: K-Best Technology Inc. Model: BL4001 Description: 1. 2400~2483.5 MHz unlicensed ISM Band 2. IEEE 802.11 Standard 3. Provides DC Power to the ODU with PoE (Power over Ethernet). 4. 20 dB receive gain for the ODU 5. Bi-directional TDD technology 6. Transmitter and receiver LED 7. Waterproof housing 8. The Z-Com WLAN Access Point is currently certified with FCC ID: M4Y-325H2 9. 20dBm output power levels. 10. Antenna used: Antenna Model Antenna type Antenna Gain (dBi) Operation Restrictions KBNT2402-17 omni 2 --- KBNT2406-17 omni 6 --- KBNT2411-17 omni 11 --- KBNT2416-14 sector 16 --- KBNT2418-16 panel 18 fixed, point-to-point operation KBNT2420-13 grid 20 fixed, point-to-point operation KBNT2424-13 grid 24 fixed, point-to-point operation Note: According to 15.247(b)(4)(i), Systems operating in the 2400-2483.5 MHz band that are used exclusively for fixed, point-to-point operations may employ transmitting antennas with directional gain greater than 6 dBi provided the maximum peak output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi. Maximum conducted output power (measured): 19.29 dBm or 84.92 mW FCC ID: QZGBL4001-001 The following table lists the provided authorized antennas: Antenna Gain Model Antenna Type (dBi) Numeric KBNT2402-17 omni 2 1.58 KBNT2406-17 omni 6 3.98 KBNT2411-17 omni 11 12.59 KBNT2416-14 sector 16 39.81 KBNT2418-16 panel 18 63.10 KBNT2420-13 grid 20 100.00 KBNT2424-13 grid 24 251.19 Below is an example of the RF Exposure Statement: Notice: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 2 meters from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user's authority to operate the device. FCC ID: QZGBL4001-001 Relative Requirement for Compliance According to section 1.1310 of FCC 47 CFR Part 1, limits for maximum permissible exposure (MPE) are as following: TABLE 1 – LIMITS FOR MAXIMUN PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.0 .................. 614 1.63 *(100) 6 3-30 ..................... 1842/f 4.89/f *(900/f 2 ) 6 30-300 .................. 61.4 0.163 1.0 6 300-1500 ............... ...................... ...................... f/300 6 1500-100,000 ......... ...................... ...................... 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 ............... 614 1.63 *(100) 30 1.34-30 ............... 824/f 2.19/f *(180/f2) 30 30-300 .................. 27.5 0.073 0.2 30 300-1500 ............... ...................... ...................... f/1500 30 1500-100,000 ......... ...................... ...................... 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density NOTE 1 TO TABLE 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational / controlled limits apply provided he or she is made aware of the potential for exposure. NOTE 2 TO TABLE 1: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. FCC ID: QZGBL4001-001 RF Exposure Calculations: The following information provides the minimum separation distance for the highest gain antenna provided. This calculation is based on the highest EIRP possible from the system, considering maximum power and antenna gain, and considering a 1.0 mW/cm 2 uncontrolled exposure limit. The formula shown in OET Bulletin 65 is used in the calculation. Equation from page 19 of OET Bulletin 65, Edition 97-01 is: S= PG / 4R 2 where: S = power density (in appropriate units, e.g. mW/cm 2 ) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) hence R= PG / 4S) 1/2 FCC ID: QZGBL4001-001 For our device P = 84.92 mW G = 251.19 S = Exposure limit = 1.0 mW/cm 2 R = ((84.92 * 251.19) / (4**1.0)) 1/2 = 41.20 cm For complying the FCC limits for general population/uncontrolled exposure, the minimum MPE distance is 41.20 cm.

Rev. No 2.0 FCC Part 15 EMI TEST REPORT of E.U.T. : BL4000 2.4GHz WLAN ODU FCC ID. : QZGBL4001-001 MODEL : BL4001 for APPLICANT : K-Best Technology Inc. ADDRESS : 2FI-1, No.185, Ko Wang Rd., Kau Yuan Tsun, Lung Tan Hsiang, Tao Yuan Hsien, Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34, LIN 5, DING FU TSUN, LINKOU HSIANG TAIPEI HSIEN, TAIWAN, R.O.C. Tel : (02)26023052 Fax : (02)26010910 http://www.etc.org.tw ; e-mail: [email protected] Report Number : ET93R-03-099-01 ETC Report No. : ET93R-03-099-01 FCC ID.: QZGBL4001-001 Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : K-Best Technology Inc. 2FI, -1, No. 185, Ko Wang Rd., Kau Yuan Tsun, Lung Tan Hsiang, Tao Yuan Hsien, Taiwan Manufacturer : K-Best Technology Inc. 2FI, -1, No. 185, Ko Wang Rd., Kau Yuan Tsun, Lung Tan Hsiang, Tao Yuan Hsien, Taiwan Description of EUT : a) Type of EUT : BL4000 2.4GHz WLAN ODU b) Trade Name : K-Best c) Model No. : BL4001 d) Power Supply : I/P: 100-240Vdc,50-60Hz, 1.0A, 40~50VA; O/P: +12Vdc, 2.0A, 24W Regulation Applied : FCC Rules and Regulations Part 15 Subpart B & C (2003) I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Issued Date : Dec. 15, 2004 Test Engineer : ( Tien Lu Liao) Approve & Authorized Signer : Will Yauo, Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : ET93R-03-099-01 FCC ID.: QZGBL4001-001 Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION......................................................................................................1 1.1 Product Description......................................................................................................................1 1.2 Characteristics of Device.............................................................................................................1 1.3 Test Methodology.........................................................................................................................2 1.4 Test Facility..................................................................................................................................2 2 PROVISIONS APPLICABLE.....................................................................................................3 2.1 Definition.....................................................................................................................................3 2.2 Requirement for Compliance.......................................................................................................4 2.3 Restricted Bands of Operation.....................................................................................................6 2.4 Labeling Requirement..................................................................................................................6 2.5 User Information..........................................................................................................................7 3. SYSTEM TEST CONFIGURATION.........................................................................................8 3.1 Justification..................................................................................................................................8 3.2 Devices for Tested System...........................................................................................................8 4 RADIATED EMISSION MEASUREMENT.............................................................................9 4 RADIATED EMISSION MEASUREMENT.............................................................................9 4.1 Applicable Standard.....................................................................................................................9 4.2 Measurement Procedure...............................................................................................................9 4.3 Measuring Instrument.................................................................................................................11 4.4 Radiated Emission Data.............................................................................................................12 4.4.1 RF Portion.........................................................................................................................................12 4.4.2 Radiated Eimssion of Restricted bands.............................................................................................27 4.4.3 Other Emission..................................................................................................................................32 4.5 Field Strength Calculation..........................................................................................................36 4.6 Photos of Radiation Measuring Setup........................................................................................37 5 CONDUCTED EMISSION MEASUREMENT.......................................................................42 5.1 Standard Applicable...................................................................................................................42 5.2 Measurement Procedure.............................................................................................................42 5.3 Conducted Emission Data..........................................................................................................43 5.4 Result Data Calculation..............................................................................................................44 5.5 Conducted Measurement Equipment...............................................................................…

Text truncated - open the document above for the full version.

ETC Report No. : ET93R-03-099-01 FCC ID.: QZGBL4001-001 Rev. No 2.0 Photos of Radiation Measuring Setup A. BL4001 with 2 dBi Omni antenna KBNT2402-17 ETC Report No. : ET93R-03-099-01 FCC ID.: QZGBL4001-001 Rev. No 2.0 B. BL4001 with 11 dBi Omni antenna KBNT2411-17 ETC Report No. : ET93R-03-099-01 FCC ID.: QZGBL4001-001 Rev. No 2.0 C. BL4001 with 16 dBi Sector antenna KBNT2416-14 ETC Report No. : ET93R-03-099-01 FCC ID.: QZGBL4001-001 Rev. No 2.0 D. BL4001 with 18 dBi Panel antenna KBNT2411-16 ETC Report No. : ET93R-03-099-01 FCC ID.: QZGBL4001-001 Rev. No 2.0 E. BL4001 with 24 dBi grid antenna KBNT2424-13 ETC Report No. : ET93R-03-099-01 FCC ID.: QZGBL4001-001 Rev. No 2.0 Photos of Conduction Measuring Setup