R2NSXP-800SCDMA 1x WLL Phone

CDMA 1x WLLPhone CDMA 1x WLL Phone CDMA 1x WLL Phone SAR INFORMATION THIS MODEL PHONE MEETS THE GOVERNMENT ’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and re ceiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF)energy set by the Federal Communications Commission of the U.S.Governm ent. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluate on of scientific studi es. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.*Tests for SAR are conducted with the phone transmitting at its highes t certified power level in all tested frequency bands. Although the SAR is determined at the highest ce rtified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit establis hed by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when worn on the body, as described in this user guide, is 0.824 W/kg . (Body worn measurements differ among phone models, depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov / oet / fcc id after searching on FCC ID : R2NSXP-800S . Additional information on Specific Absorption Rates (SAR)can be found on the Cellular Telecommunications &Internet Association (CTIA) web-site at http://phonefacts.net.*In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6watts/kg (W/kg)averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any agitations in measurements. Caution Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC RF EXPOSURE INFORMATION In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previous ly set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. To comply with FCC RF exposure requirements, a minimum separation distance of 2.5cm (0.98 inch) must be maintained between the user/bystander and the back of theunit, including the antenna. For more information about RF exposure, please visit the FCC website at www.fcc.gov WARNING! Read this information before use FCC Compliance Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received. Including interference that may cause undesired operation. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These lim its are designed to provi de reasonable protection against harmful interference in a residential in stallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio comm unications. However, there is no guarantee that interference will not occur in a particular in stallation. If this equipment does cause harmful interference to radio or television reception, wh ich can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienc ed radio/ tv technician for help. 7Communicate with text messages20 Write and send a text message20 Reading a saved text message 20 Erase text message 21 8Data and fax calls22 Getting started24 Configuring your data or fax software 24 To start a data or fax call 24 To receive a data or fax call 24 Manual selection of incoming data/fax calls 25 9Troubleshooting26 10Reference information 27 Batteries and chargers27 Emergency calls 31 Accessories 34 Technical Information 11Manufacturer's Warranty 1Safety5 Using this guide6 Disclaimer 6 What's in the box?7 2Basics8 Keys8 Power On/Off8 Getting a strong signal10 Making a call11 Ending a Call 11 Redial11 On-H…

Text truncated - open the document above for the full version.

SUNGIL TELECOM CO., LTD. SEONIL TECHNOPIA #1209,440, SANGDAEWON-DONG, JUNGWON-GU, SEONGNAM-CITY, GYUNGGI, KOREA Tel:+82-31-777-3121 Fax: +82-31-777-3120 April 21, 2004 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 LETTER OF AUTHORIZATION To whom it may concern: We, the undersigned, hereby authorize DIGITAL EMC Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization for model R2NSXP-800S , including signing of all documents relating to these matters. Any and all acts carried out by DIGITAL EMC Co., Ltd ., on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from SUNGIL TELECOM CO., LTD. Sincerely, Sean Chi Product Manager SUNGIL TELECOM CO., LTD.

SUNGIL TELECOM CO., LTD. SEONIL TECHNOPIA #1209,440, SANGDAEWON-DONG, JUNGWON-GU, SEONGNAM-CITY, GYUNGGI, KOREA Tel:+82-31-777-3121 Fax: +82-31-777-3120 April 21, 2004 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 In re : SUNGIL TELECOM CO., LTD. FCC ID : R2NSXP-800S FCC Part 22 Certification Request for Confidentiality Gentlemen: In accordance with 0.459 of CFR 47, SUNGIL TELECOM CO., LTD. hereby requests confidentiality of the Block diagram, Schematics, Parts list, Tune-up Procedure, Operational Description of the attached test report. These documents contain detailed system and equipment description and related information about the product which SUNGIL TELECOM CO., LTD considers to be proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, SUNGIL TELECOM CO., LTD. considers that this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, Sean Chi Product Manager SUNGIL TELECOM CO., LTD.

External Photograph FCC ID : R2NSXP-800S External Photograph FCC ID : R2NSXP-800S External Photograph FCC ID : R2NSXP-800S External Photograph FCC ID : R2NSXP-800S External Photograph FCC ID : R2NSXP-800S External Photograph FCC ID : R2NSXP-800S

FCC ID: R2NSXP-800S FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase (SEE NEXT PAGE) FCC ID: R2NSXP-800S FCC IDENTIFICATION (NAME PLATE) INFORMATION - The FCC label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. FCC ID: R2NSXP-800S This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Internal Photograph FCC ID : R2NSXP-800S Internal Photograph FCC ID : R2NSXP-800S Internal Photograph FCC ID : R2NSXP-800S Internal Photograph FCC ID : R2NSXP-800S Internal Photograph FCC ID : R2NSXP-800S

PROBE CALIBRATION DIGITAL EMC

SAR Test Photograph FCC ID : R2NSXP-800S SAR Test Photograph FCC ID : R2NSXP-800S SAR Test Photograph FCC ID : R2NSXP-800S SAR Test Photograph FCC ID : R2NSXP-800S

SXP-800S SAM(835MHz) Phantom; Flat Section; Probe: ET3DV6 - SN1702; ConvF(6.60,6.60,6.60); 835 MHz Body: σ = 1.00 mho/m ε r = 52.9 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; SAR (1g): 0.824 mW/g, SAR (10g): 0.576 mW/g; FCC ID: R2NSXP-800S CDMA Mode, Ch.1013[824.70MHz]; Standard Battery; Ambient Temp = 23 °C /Meas. Tissue Temp. = 21 °C Conducted Power = 24dBm; Spacing = 2.5cm From antenna to flat phantom; Antenna Fixed Test Date -- April 16, 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] SAR Tot [mW/g] 8.85E-21.77E-12.66E-13.54E-14.43E-15.31E-16.20E-17.08E-17.96E-18.85E-1 <DIGITAL EMC> SXP-800S SAM(835MHz) Phantom; Flat Section; Probe: ET3DV6 - SN1702; ConvF(6.60,6.60,6.60); 835 MHz Body: σ = 1.00 mho/m ε r = 52.9 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; SAR (1g): 0.781 mW/g, SAR (10g): 0.541 mW/g; FCC ID: R2NSXP-800S CDMA Mode, Ch.0384[836.52MHz]; Standard Battery; Ambient Temp = 23 °C /Meas. Tissue Temp. = 21 °C Conducted Power = 24dBm; Spacing = 2.5cm From antenna to flat phantom; Antenna Fixed Test Date -- April 16, 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] SAR Tot [mW/g] 8.37E-21.67E-12.51E-13.35E-14.18E-15.02E-15.86E-16.70E-17.53E-18.37E-1 <DIGITAL EMC> SXP-800S SAM(835MHz) Phantom; Flat Section; Probe: ET3DV6 - SN1702; ConvF(6.60,6.60,6.60); 835 MHz Body: σ = 1.00 mho/m ε r = 52.9 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; SAR (1g): 0.772 mW/g, SAR (10g): 0.537 mW/g; FCC ID: R2NSXP-800S CDMA Mode, Ch.0777[848.31MHz]; Standard Battery; Ambient Temp = 23 °C /Meas. Tissue Temp. = 21 °C Conducted Power = 24dBm; Spacing = 2.5cm From antenna to flat phantom; Antenna Fixed Test Date -- April 16, 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] SAR Tot [mW/g] 8.24E-21.65E-12.47E-13.30E-14.12E-14.94E-15.77E-16.59E-17.42E-18.24E-1 <DIGITAL EMC> SXP-800S SAM(835MHz) Phantom; Section; Probe: ET3DV6 - SN1702; ConvF(6.60,6.60,6.60); 835 MHz Body: σ = 1.00 mho/m ε r = 52.9 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; ; FCC ID: R2NSXP-800S CDMA Mode, Ch.1013[824.70MHz]; Standard Battery; Ambient Temp = 23 °C /Meas. Tissue Temp. = 21 °C Conducted Power = 24dBm; Spacing = 2.5cm From antenna to flat phantom; Antenna Fixed Test Date -- April 16, 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] <DIGITAL EMC> 0.00.20.40.60.81.01.2 0 1020 3040 50 SAR tot [mW/g] [mm] SXP-800S SAM(835MHz) Phantom; Flat Section; Probe: ET3DV6 - SN1702; ConvF(6.60,6.60,6.60); 835 MHz Body: σ = 1.00 mho/m ε r = 52.9 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; SAR (1g): 0.753 mW/g, SAR (10g): 0.525 mW/g; FCC ID: R2NSXP-800S CDMA Mode, Ch.1013[824.70MHz]; With Charger; Ambient Temp = 23 °C /Meas. Tissue Temp. = 21 °C Conducted Power = 24dBm; Spacing = 2.5cm From antenna to flat phantom; Antenna Fixed Test Date -- April 16, 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] SAR Tot [mW/g] 8.20E-21.64E-12.46E-13.28E-14.10E-14.92E-15.74E-16.56E-17.38E-18.20E-1 <DIGITAL EMC> SXP-800 SAM(835MHz) Phantom; Flat Section; Probe: ET3DV6 - SN1702; ConvF(6.60,6.60,6.60); 835 MHz Body: σ = 1.00 mho/m ε r = 52.9 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; SAR (1g): 0.513 mW/g, SAR (10g): 0.356 mW/g; FCC ID: R2NSXP-800S CDMA Mode, Ch.0384[836.52MHz]; With Charger; Ambient Temp = 23 °C /Meas. Tissue Temp. = 21 °C Conducted Power = 24dBm; Spacing = 2.5cm From antenna to flat phantom; Antenna Fixed Test Date -- April 16, 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] SAR Tot [mW/g] 5.32E-21.06E-11.60E-12.13E-12.66E-13.19E-13.72E-14.26E-14.79E-15.32E-1 < DIGITAL EMC > SXP-800S SAM(835MHz) Phantom; Flat Section; Probe: ET3DV6 - SN1702; ConvF(6.60,6.60,6.60); 835 MHz Body: σ = 1.00 mho/m ε r = 52.9 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; SAR (1g): 0.635 mW/g, SAR (10g): 0.437 mW/g; FCC ID: R2NSXP-800S CDMA Mode, Ch.0777[848.31MHz]; With Charger; Ambient Temp = 23 °C /Meas. Tissue Temp. = 21 °C Conducted Power = 24dBm; Spacing = 2.5cm From antenna to flat phantom; Antenna Fixed Test Date -- April 16, 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] SAR Tot [mW/g] 6.50E-21.30E-11.95E-12.60E-13.25E-13.90E-14.55E-15.20E-15.85E-16.50E-1 <DIGITAL EMC> SXP-800S SAM(835MHz) Phantom; Section; Probe: ET3DV6 - SN1702; ConvF(6.60,6.60,6.60); 835 MHz Body: σ = 1.00 mho/m ε r = 52.9 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; ; FCC ID: R2NSXP-800S CDMA Mode, Ch.1013[824.70MHz]; With Charger; Ambient Temp = 23 °C /Meas. Tissue Temp. = 21 °C Conducted Power = 24dBm; Spacing = 2.5cm From antenna to flat phantom; Antenna Fixed Test Date -- April 16, 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] <DIGITAL EMC> 0.00.20.40.60.81.01.2 0 1020 3040 50 SAR tot [mW/g] [mm]

DEMC#DR50110404D Copyright ○ c 2004, DIGITAL EMC Co., Ltd. Page 1 of 22 683-3, Yubang-Dong, Yongin-Si, Kyunggi-Do, Korea. 449-080 Tel: +82-31-321-2664 Fax: +82-31-321-1664 http://www.digitalemc.com SAR TEST REPORT Dates of Tests: April 16, 2004 Test Report S/N:DR50110404D Test Site : DIGITAL EMC CO., LTD. MODEL NO. APPLICANT EUT Type: CDMA 1x WLL Phone TX Frequency Range: 824.70 ~848.31 MHz (CDMA) RX Frequency Range: 869.70 ~893.31 MHz (CDMA) RF Output Power: 0. 365W ERP CDMA (25.62 dBm) - With the Battery 0.378W ERP CDMA (25.78dBm) - With the Adaptor Max. SAR Measurement: 0.824W/kg CDMA Body SAR - With the Battery 0.753W/kg CDMA Body SAR - With the adaptor Model(s): SXP-800S Rule Part(s): §2.1093; FCC/OET Bulletin Supplement C[July 2001] Application Type: Certification Test Device Serial No.: Identical prototype Data of issue April 16, 2004 D.M.JUNG (Manager) This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C (2001) and IEEE Std. 1528-200X (Draft 6.4, July 2001). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. R2NSXP-800S SUNGIL TELECOM CO., LTD. DEMC#DR50110404D Copyright ○ c 2004, DIGITAL EMC Co., Ltd. Page 2 of 22 1. INTRODUCTION .................................................................................................................... 3 SAR DEFINITION .................................................................................................................. 3 2. SAR MEASUREMENT SETUP.................................................................................................. 4 Robotic System............................................................................................................................. 4 System Hardware ......................................................................................................................... 4 System Electronics........................................................................................................................ 4 3. DASY3 E-FIELD PROBE SYSTEM........................................................................................... 5 Probe Measurement System.......................................................................................................... 5 Probe Specifications ..................................................................................................................... 5 4. Probe Calibration Process............................................................................................................. 6 Dosimetric Assessment Procedure................................................................................................ 6 Free Space Assessment ................................................................................................................ 6 Temperature Assessment ............................................................................................................. 6 5. PHANTOM & EQUIVALENT TISSUES.................................................................................... 7 SAM Phantom ............................................................................................................................. 7 Brain & Muscle Simulating Mixture Characterization ................................................................ 7 Device Holder for Transmitters.................................................................................................... 7 6. TEST SYSTEM SPECIFICATIONS............................................................................................ 8 Automated Test System Specifications......................................................................................... 8 7. DOSIMETRIC ASSESSMENT & PHANTOM SPECS ............................................................. 9 Measurement Procedure................................................................................................................ 9 Specific Anthropomorphic Mannequin (SAM) Specifications..................................................... 9 8. DEFINITION OF REFERENCE POINTS .................................................................................. 10 EAR Reference Point.................................................................................................................... 10 Handset Reference Points............................................................................................................. 10 9. TEST CONFIGURATION POSITIONS ..................................................................................... 11 Positioning for Cheek/Touch ....................................................................................................... 11 Positioning for Ear /15° Tilt ......................................................................................................... 12 Body Holster /Belt Clip Configurations ....................................................................................... 13 10. ICNIRP GUIDELINES RF EXPOSURE LIMITS..................................................................... 14 Uncontrolled Environment ........................................................................................................... 14 Controlled Environment................................................................................................................ 14 11. MEASUREMENT UNCERTAINTIES...................................................................................... 15 SAR Measurement Uncertain…

Text truncated - open the document above for the full version.

835MHz Dipole Validation SAM(835MHz) Phantom; Flat Section; Probe: ET3DV6 - SN1702; ConvF(6.52,6.52,6.52); Med. parameter 835 MHz Brain: σ = 0.87 mho/m ε r = 40.5 ρ = 1.00 g/cm 3 ; Crest factor: 1.0; SAR (1g): 2.49 mW/g, SAR (10g): 1.59 mW/g; Dipole validation: for f < 1 GHz, distance to the liquid d = 15 mm for f > 1 GHz, distance to the liquid d=10 mm Test Date -- April 16 2004 [FCC/OET Bulletin65 - Supplement C, July 2001] SAR Tot [mW/g] 2.63E-15.26E-17.89E-11.05E+01.31E+01.58E+01.84E+02.10E+02.37E+02.63E+0 <DIGITAL EMC>

Date 2003. 12. 23 Version No. 1.0 Subject DSW-800 1/13 DKS CO. Table of Contents 1. Specification........................................................................................................................ 1 1.1. General Standard...................................................................................................................................1 1.2. Electrical Standard.................................................................................................................................2 1.3. Mechanical Standard............................................................................................................................2 2. Test Procedure & Measurement .......................................................................................... 2 2.1. External Test............................................................................................................................................2 2.2. Electrical Feature Inspection...............................................................................................................3 2.2.1. Materials.............................................................................................................................................................3 2.2.2. Inspection...........................................................................................................................................................3 2.3. Beam Pattern..........................................................................................................................................5 2.3.1. Materials.............................................................................................................................................................5 2.3.2. Inspection...........................................................................................................................................................6 3. Packing, Shipping, Handling............................................................................................... 7 3.1. Exterior Option........................................................................................................................................7 3.2. Packing.....................................................................................................................................................7 4. Exterior................................................................................................................................ 8 5. Test Data Sheet ................................................................................................................... 9 6. Data Sheet ......................................................................................................................... 10 6.1. V.S.W.R..................................................................................................................................................10 6.2. Beam pattern........................................................................................................................................11 6.2.1. Azimuth ...............................................................................................................................................................11 6.2.2. Elevation.............................................................................................................................................................12 6.3. Impedance.............................................................................................................................................13 1. Specification 1.1. General Standard General specification Date 2003. 12. 23 Version No. 1.0 Subject DSW-800 2/13 DKS CO. Model name DSW-800 Antenna type Half Wavelength Antenna 1.2. Electrical Standard Electrical specification Frequency range 824 ~ 894㎒ V.S.W.R 1.9 : 1 Max. Gain(dBi) 2±0.5 Radiation pattern Omni-directional Polarization Vertical Max Power(W) 5W Max. Impedance 50 Ω Normalizer 1.3. Mechanical Standard Mechanical specification Connector type TNC Male Cover material Urethane Color Black not bright Temperature range -30°C ~ 70°C Weight 37 ± 2g Dimension TBD 2. Test Procedure & Measurement 2.1. External Test To check the unity Antenna’s exterior, size, connector and etc. with the exterior indicated in item #6. Date 2003. 12. 23 Version No. 1.0 Subject DSW-800 3/13 DKS CO. 2.2. Electrical Feature Inspection 2.2.1. Materials Equipment Model QuantityStandard Network Analyzer HP8752C Or equipment with the equivalent 1EA · Freq. Range : 300KHz ~ 3GHz · Accuracy : <5ppm · Dynamic Range : 105dB · Trace at ±200dB · Resolution : 1Hz · Impedance : 50 Ω Adaptor 1EA · N(M)-TNC(F) Calibration Kit HP85032B 1Set · DC ~ 6GHz (N-Type) 2.2.2. Inspection Figure 1. This how Network Analyzer is connected when inspecting the Network Analyzer 2.2.2.1. Inspection 가. Equipment Setting and Calibration ㉠ Equipment Setting ⓐ Bandwidth : Center Frequency: 860.0MHz, Span :200.0MHz ⓑ Source Power : 10dBm, ⓒ IF Bandwidth : 1000Hz ⓓ Number of Point : 401 PRINTER Date 2003. 12. 23 Version No. 1.0 Subject DSW-800 4/13 DKS CO. ㉡ Calibration Using N-Type Cal Kit applying O.S.L. method, Calibrate Port number 1. ⓐ S 11 Calibration : Open Port #1, Calibrate after connecting the Load short. ㉢ Calibration Check ⓐ Connect Load to Port #1 to check S 11’ s V.S.W.R is less than 1.02 : 1 ⓑ Connect Load to Port #1 to check S 21 is less than -80.0dB. If not satisfied with the result, repeat procedure ㉡’ s Calibration. 나. Inspection Method and Contents Item Inspection Method Standard VSWR Connect ANT to the positioner and measure the S 11 within Operating Band, as shown above on Figure 2. 1.9:1 Max. Impedance Connect ANT to the positioner and measure the S 11 값that’ s on Smith Chart within the Operating Band, as shown above on Figure w. 50 ± 20Ω Date 2003. 12. 23 Version No. 1.0 Subject DSW-800 5/13 DKS CO. 2.3. Beam Pattern 2.3.1. M…

Text truncated - open the document above for the full version.

DEMC#DR50110404C Copyright ○ c 2004, DIGITAL EMC Co., Ltd. Page 1 of 22 683-3, Yubang-Dong, Yongin-Si, Kyunggi-Do, Korea. 449-080 Tel: +82-31-321-2664 Fax: +82-31-321-1664 http://www.digitalemc.com CERTIFICATE OF COMPLIANCE FCC Part 22 Certification Dates of Tests: April 13 ~ 20, 2004 Test Report S/N:DR50110404C Test Site : DIGITAL EMC CO., LTD. Model No. APPLICANT Classification : Licensed Non-Broadcast Station Transmitter (TNB) FCC Rule Part(s) : §22.901(d), §15, §2 EUT Type : CDMA 1x WLL Phone Model name : SWP-800S Serial number : Identical prototype TX Frequency Range : 824.70 ~848.31 MHz (CDMA) RX Frequency Range : 869.70 ~893.31 MHz (CDMA) Max. RF Output Power : 0. 365W ERP CDMA (25.62 dBm) - With Battery 0.378W ERP CDMA (25.78dBm) - With Charger Max. SAR Measurement : 0.824W/kg CDMA Body SAR - With Battery 0.753W/kg CDMA Body SAR - With Charger Emission Designators: : 1M25F9W Date of Issue : April 22, 2004 I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. R2NSXP-800S SUNG IL TELECOM CO., LTD DEMC#DR50110404C Copyright ○ c 2004, DIGITAL EMC Co., Ltd. Page 2 of 22 TABLE OF CONTENTS ATTACHMENT A: COVER LETTER(S) ATTACHMENT B: ATTESTATION STATEMENT(S) ATTACHMENT C: TEST REPORT 1.1 SCOPE 3 2.1 INTRODUCTION 4 3.1 INSERTS 5 4.1 DESCRIPTION OF TESTS 6-8 5.1 EFFECTIVE RADIATED POWER OUTPUT 9-10 6.1 RADIATED MEASUREMENTS 11-13 7.1 FREQUENCY STABILITY 14-15 8.1 EMISSION TEST DATA 16-17 9.1 PLOTS OF EMISSIONS 18 10.1 LIST OF TEST EQUIPMENT 19-20 11.1 SAMPLE CALCULATIONS 21 12.1 CONCLUSION 22 ATTACHMENT D: TEST PLOTS ATTACHMENT E: FCC ID LABEL & LOCATION ATTACHMENT F: TEST SETUP PHOTOGRAPHS ATTACHMENT G: EXTERNAL PHOTOGRAPHS ATTACHMENT H: INTERNAL PHOTOGRAPHS ATTACHMENT I : BLOCK DIAGRAM(S) ATTACHMENT J: SCHEMATIC DIAGRAM(S) ATTACHMENT K: OPERATIONAL / CIRCUIT DESCRIPTION ATTACHMENT L: PARTS LIST/TUNE UP PROCEDURE ATTACHMENT M: USER’S MANUAL ATTACHMENT O: SAR MEASUREMENTS REPORT ATTACHMENT P: SAR TEST PLOTS ATTACHMENT Q: SAR TEST SETUP PHOTOGRAPHS ATTACHMENT R: DIPOLE VALIDATION (S) ATTACHMENT S: PROBE CALIBRATION DEMC#DR50110404C Copyright ○ c 2004, DIGITAL EMC Co., Ltd. Page 3 of 22 MEASUREMENT REPORT 1.1 Scope Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission. §2.1033 General Information z FCC ID: z Quantity: z Emission Designators: z Tx Freq. Range: z Rx Freq. Range: z Max. Power Rating: z FCC Classification(s): z Equipment (EUT) Type: z Modulation(s): z Frequency Tolerance: z FCC Rule Part(s): z Dates of Tests: z Place of Tests: z Test Report S/N: R2NSXP-800S Quantity production is planned 1M25F9W (CDMA) 824.70 ~848.31 MHz (CDMA) 869.70 - 893.31 MHz (CDMA) 0.365W ERP CDMA (25.62 dBm) - With Battery 0.378 ERP CDMA (25.78 dBm) - With Charger Licensed Non-Broadcast Station Transmitter (TNB) CDMA 1x WLL Phone CDMA ± 0.00025 % (2.5ppm) §22.901(d), §15, §2 April 13 ~ 20, 2004 DIGITAL EMC DR50110404C Applicant: SUNGIL TELECOM CO., LTD. Address: SEONIL TECHNOPIA #1209, 440, SANGDAEWON-DONG, JUNGWON-GU, SEONGNAMCITY, GYUNGGI, KOREA Attention: Sean Chi (Product Manager…

Text truncated - open the document above for the full version.