RAQ1693Bluetooth Wireless PTT

– 0 – Bluetooth Remote PTT User’s Guide Important Safety Information Please observe the following to ensure reliable operation of the Bluetooth Remote PTT 1. Read this manual thoroughly and observe the operating instructions and information provided. 2. Do not expose the equipment to extreme temperatures or high relative humidity and protect it from direct sunlight and dusty conditions. 3. Clean the equipment with a soft, damp cloth. Do not use any solvents or aggressive cleaning agents. 4. Only connect approved accessories. 5. Only use the power plug supplied. 6. Never open the unit. Opening the unit annuls claims under the terms of guarantee and exposes the person to the risk of an electric shock. 7. Repairs to defective units should only be carried out by service centers of Giant International Ltd.. 8. Batteries built into device are NOT user replaceable. Discard used batteries according to the local regulations. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment. Remote PTT Overview 1. Power on/ Off Multi Function Button (MFB) 2. Push-to-Talk (PTT) Button 3. Bluetooth LED Indicator 4. Headset Jack 5. Charging Port – 1 – Turn it on/off To turn on/off your remote PTT, press and hold the [MFB] button for about 2s. Charge Remote PTT The Remote PTT comes with rechargeable battery that must be fully charged before you use it for the first time. 1. Connect the power adapter to the unit. Plug the AC adapter into the electrical outlet. 2. The LED will be red when charging. If the LED is not red, check the connection. 3. During charging, the red LED will be lit. When the remote PTT is fully charged, the red LED will be blue. 4. Remove the AC adapter from the remote PTT. Note: Charging while the remote PTT is on, the remote PTT will turn off automatically. Pairing with a Bluetooth FRS 1. Turn off the remote PTT. 2. Press and hold the [MFB] button until the remote PTT indicator light flashes blue and red. 3. The remote PTT now is in pairing mode. Release the button. The indicator light will continue flashing red and blue. 4. If pairing was successful, the remote LED will flash blue at a 5s interval. 5. If pairing fails, turn the remote PTT and FRS off and repeat the process. Reconnect After initially pairing and connecting your FRS and Remote PTT, when you turn on the Remote PTT, it will reconnect the paired FRS; however, you can press [MFB] once to connect rapidly. Using your Remote PTT The remote PTT is worked with headset (With Microphone / Without Microphone). Using the headset with Microphone: 1. Press [PTT] on this Remote PTT Button to transmit and speak towards the headset's microphone. Receiver sound will come out from the headset when [PTT] release. Using the headset without Microphone: 1. Press [PTT] on this Remote PTT Button to transmit and speak towards the FRS/GMRS radio's microphone when using a VOX Headset without a Microphone. Receiver sound will come out from the headset when [PTT] release. Status of LED under different operation mode Action Button Action / StatesLED Power on Press and hold MFB button 2 seconds Blue flashes 3 times Power off Press and hold MFB button 4 seconds Red Long 1 second and turn off Pairing mode (1st time) Press and hold MFB for 2 seconds when powering on. (After 1st pairing) Press and hold MFB for 6 seconds when powering on. Red and Blue Blink alternately Stand by (connectable) No pairing Blue LED flashes at a 2 seconds interval Stand by(connected) paired Blue LED flashes at a 5 seconds interval Steady Red(Without Headset) PTT (Push-To-Talk) Press and hold PTT Button Steady Red and Blue(With Headset) – 2 – Release PTT Release PTT button Blue LED flashes at a 5 seconds interval Charging Steady Red Charged Steady Blue Low Battery Flash Red Auto Power OFF 5 minutes after Connectable mode ( No pairing ) LEDs OFF

Date: July 3, 2013 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern: The Giant Telecom Ltd. , the undersigned, hereby authorizes Mrs. Ivy.Zhu from Shenzhen Morlab Communications Technology Co., Ltd., to act on the behalf of the Giant Telecom Ltd. solely in matters relating to the application for an FCC equipment authorization for FCC ID: RAQ1693 including the signing of documents in connection with this Application. Necessary acts carried out by Shenzhen Morlab Communications Technology Co., Ltd. on our behalf of the Giant Telecom Ltd. in connection with the Application shall have the same effect as acts of the Giant Telecom Ltd.. The Giant Telecom Ltd. also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Thank you for your attention to this matter. Yours Sincerely, Kun Xiong A. Manager

Date: July 3, 2013 Re: FCC ID: RAQ1693 Pursuant to 47 CFR 0.459, Giant Telecom Ltd. request confidential protection of the following documents submitted electronically in furtherance of the above-reference application as containing propriety information listed below: ƵSchematic ƵBlock Diagram ƵOperational Description ƵParts List This information represents intellectual property of Giant Telecom Ltd. and it is subject to competition. This information should not be made routinely available for public inspection, and Giant Telecom Ltd. reserves the right to discern which parties can obtain access to this information. Kun Xiong A. Manager

Aug1 st ,2013  Subject:LetterofAuthorization DearSir, We,theundersigner,herebyauthorizeKunXiongofGiantTelecomLtd.onourbehalfin allmattersrelatingtoapplicationforWalkieͲTalkieandBluetoothWirelessPTT(Model: MU350R /MU560CR /MU351R, FCC ID:RAQMUEFJ; Model:1693,FCCID:RAQ1693)authorization, includingthesigningofalldocumentsrelatingtothesematters.Anyandallactscarriedoutby KunXiongonourbehalfshallhavethesameeffectasactsofourown.  YoursSincerely    YuminZhou A. Manager GiantTelecomLimited 

External Photos 1. EUT full view with accessories 2. EUT front view 3. EUT rear view 4. EUT left side view 5. EUT right side view 6. EUT top view 7. EUT bottom view

Internal Photos 1. EUT uncover view 2. Mainboard front view 3. Mainboard rear view 4. BT chip view 5. BT antenna view

Report No.: SZ13040103E02 Page 2 of 17 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 3 1.1 EUT Description ......................................................................................................................... 3 1.2 Test Standards and Results ........................................................................................................ 5 1.3 Facilities and Accreditations ...................................................................................................... 6 1.3.1 Facilities .................................................................................................................................... 6 1.3.2 Test Environment Conditions .................................................................................................... 6 1.3.3 Measurement Uncertainty ......................................................................................................... 6 2. TEST CONDITIONS SETTING............................................................................................... 7 2.1 Test Mode .................................................................................................................................... 7 2.2 Test Setup and Equipments List ................................................................................................ 8 2.2.1 Conducted Emission.................................................................................................................. 8 2.2.2 Radiated Emission ..................................................................................................................... 8 3. 47 CFR PART 15B REQUIREMENTS .................................................................................. 12 3.1 Conducted Emission ................................................................................................................. 12 3.1.1 Requirement ............................................................................................................................ 12 3.1.2 Test Description ...................................................................................................................... 12 3.1.3 Test Result ............................................................................................................................... 12 3.2 Radiated Emission .................................................................................................................... 14 3.2.1 Requirement ............................................................................................................................ 14 3.2.2 Test Description ...................................................................................................................... 14 3.2.3 3.2.3 Frequency range of measurement .................................................................................. 14 3.2.4 Test Result ............................................................................................................................... 15 Change History Issue Date Reason for change 1.0 July 17, 2013 First edition Report No.: SZ13040103E02 Page 3 of 17 1. GENERAL INFORMATION 1.1 EUT Description EUT Type ..........................Bluetooth Wireless PTT Serial No. ..........................(n.a., marked #1 by test site) Hardware Version ............ .N/A Software Version ............... Applicant ........................... Manufacturer ..................... N/A Giant Telecom Ltd. 33/F, AIA Kowloon Tower, Landmark East, 100 How Ming Street, Kwun Tong , Kowloon DONGGUAN WISETRONICS TELECOM EQUIPMENT CO. LTD. Elite Industrial City, Melin District, Dailing Mount Town, Dongguan Guangdong, China Modulation Type .............. .FHSS Power supply 1 .................Battery Brand Name: Lishen Model No.: SP0405AC Serial No.: (n.a. marked #1 by test site) Capacitance: 140mAh Rated Voltage: 3.7V Charge Limit: 4.2V Power supply 2 ................ .Battery Brand Name: SPRINGPOWER Model No.: 552036AY Serial No.: (n.a. marked #1 by test site) Capacitance: 320mAh Rated Voltage: 3.7V Charge Limit: 4.2V Ancillary Equipment 1 ..... .AC Adapter (Charger for Battery) Brand Name: HSK Model No.: HSKSA3.25W650-1U0 Serial No.: (n.a. marked #1 by test site) Rated Input: 100-240V, 200mA, 50/60Hz Rated Output: 5V, 650mA Note: 1. The EUT is a Bluetooth Wireless PTT which is equipped with a USB port for charging when it was connected with the ancillary equipments e.g. the AC Adapter and the USB Cable . The EUT is mainly used for Walkie-Talkie. Report No.: SZ13040103E02 Page 4 of 17 2. For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Report No.: SZ13040103E02 Page 5 of 17 1.2 Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart B: No. Identity Document Title 1 47 CFR Part 15 Radio Frequency Devices Test detailed items/section required by FCC rules and results are as below: No. Section Description Result 1 15.107 Conducted Emission PASS 2 15.109 Radiated Emission PASS NOTE: The tests were performed according to the method of measurements prescribed in ANSI C63.4 2009. Report No.: SZ13040103E02 Page 6 of 17 1.3 Facilities and Accreditations 1.3.1 Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at FL.3, Building A, FeiYang Science Park, No.8 LongChang Road, Block 67, BaoAn District, ShenZhen, GuangDong Province, P. R. China 518101 . The test site is constructed in conformance with the requirements of ANSI C63.4(2009) and CISPR Publication 22(2010); the FCC registr…

Text truncated - open the document above for the full version.

Test Setup Photos 1. Conducted emission main’s port front view 2. Conducted emission main’s port side view 3. Radiated emission (9KHz-30MHz) 4. Radiated emission (30MHz-1GHz) 5. Radiated emission (above 1GHz)