RFK-CBAHP800Single Channel Power Amplifier

Cellular In-Building Amplifier Installation Manual Page 1 of 4 All brands and trademarks are the property of their respective owners. Copyright 2003, Janizary Holdings, Inc. All rights reserved. 11/16/05 Rev A D000003 Designed and manufactured under license from Motorola, Inc. in the USA Note: Before installing the Cyfre™ Amplifier, please read the entire contents of this manual. Section # 1 Parts List Ite m Q ty Description 1 1 Cyfre ™ Amplifier 2 1 Cyfre external antenna 3 4 5 1 1 1 Cyfre interior antenna with 4 meters of low loss antenna cable Cyfre 120 VAC power supply Cyfre 4 meter low loss antenna cable with “N” connectors Section # 2 Tools and Other Materials Required Item Description 1 Electric drill (as required for amplifier mounting holes, and external antenna mounting) 2 Chisel and Phillips Screw drivers, 8mm and 10mm wrenches 3 Qty 8 fasteners (length and type as required for amplifier and external antenna mounting) 4 Wire cutters / strippers 5 Cables ties for clamping the external and interior antenna cables to rigid structure Section # 3 WARNINGS! ∇ Antennas must be mounted a minimum distance of 50 cm (1.64ft) away from any person. ∇ When selecting a location for the interior antenna a minimum distance of 6 feet (1.82m) distance away from the amplifier. ∇ When 2 or more antennas are located in the same area they must be mounted at different heights to insure optimum performance. ∇ Exterior antennas can only be installed outdoors. Under no circumstances can an exterior antenna be installed indoors, Doing so will result in amplifier failure and void the warranty. ∇ The power supply must be plugged into a 120 VAC electrical outlet that is connected to a circuit breaker of a minimum of 1 ampere. ∇ Under no circumstances should the amplifier be powered up without a properly connected 50 ohm 800/ 1900 MHz dual band cellular antenna connected to both the internal and external connections or the amplifier may be damaged, resulting in the manufacturer’ warranty being voided. ∇ For optimum performance and compatibility with cellular service provider requirements, it is recommended that the external antenna be installed above the roofline of a building with a clear view of the surrounding area ∇ Use of cellular amplifiers with antennas of higher gains than 15dBi gain is in violation of FCC regulations for which the offender will be fully liable, and warranty claims will be voided. ∇ Do not extend the external antenna cable with another coaxial cable. The additional loss of the cable length and connectors will greatly diminish the performance of the amplifier. It is recommended that only qualified or informed installation technicians install this product in a building. Installation by any other person is at the risk of the owner and operator. Cellular In-Building Amplifier Installation Manual Page 2 of 4 All brands and trademarks are the property of their respective owners. Copyright 2003, Janizary Holdings, Inc. All rights reserved. 11/16/05 Rev A D000003 Designed and manufactured under license from Motorola, Inc. in the USA Section # 4 Installation Cautions ∇ Use caution to avoid drilling through or near electrical, water or gas lines. ∇ Do not mount the signal amplifier or its associated wiring in a location that may contain hazardous materials or materials that are corrosive. ∇ Do not attempt to ground the external antenna. It is designed with its own interior ground system. ∇ The interior antenna requires a ground plane. It should be mounted on any type of metal that will have a minimum of one square foot of surface area under the antenna base. ∇ Caution: DO NOT INSTALL THE INTERIOR ANTENNA IN A HAZARDOUS LOCATION THAT MAY CONTAIN ANY TYPE OF VOLITILE VAPORS. Section # 5 Selecting a Suitable Location To Install The Amplifier ∇ Locate a suitable place to mount the cellular band amplifier. For exterior antennas you must mount the antenna above the roofline of the building at a distance that can be reached from the supplied external antenna cable, on a shelf near a electrical power source, in a dry area that is well ventilated. The amplifier’s location should be easily accessible and mounted away from moving parts, as well as excessive heat and moisture. ∇ Antennas must be mounted a minimum distance of 50 cm (1.64ft) away from any person. ∇ When selecting a location for the interior antenna a minimum distance of 6 feet (1.82m) distance away from the amplifier. ∇ When 2 or more antennas are located in the same area, they must be mounted at different heights to insure optimum performance. ∇ Exterior antennas can only be installed outdoors. Under no circumstances can an exterior antenna be installed indoors, Doing so will result in amplifier failure and void the warranty. ∇ If the signal level is increased in some areas but not others, it may be due to location of interior antenna or building materials acting as a shield for the radio signals. This can be overcome by re-positioning the interior antenna or, the use of 2 internal antennas in conjunction with a very low loss high quality splitter. Please note that the interior antennas must be at least twenty five (25) feet apart and should be separated by gypsum clad, masonry or metal constructed wall. Cellular In-Building Amplifier Installation Manual Page 3 of 4 All brands and trademarks are the property of their respective owners. Copyright 2003, Janizary Holdings, Inc. All rights reserved. 11/16/05 Rev A D000003 Designed and manufactured under license from Motorola, Inc. in the USA Typical Installation For the Cyfre™ In-Building Amplifier Series Section # 6 Installation Of The Cellular In-Building Amplifier 1. Unpack the box with the amplifier, power supply, external antenna, antenna cable and interior antenna. 2. The first item is to find a suitable location for the exterior antenna, which will give a clear view without obstruction, and also allow the antenna cable to penetrate either the roof area or a wall area below the roofline.…

Text truncated - open the document above for the full version.

LEON PAUL KASS, LLC CONSULTANT IN WIRELESS COMMUNICATION 9695 135 th Street Seminole, Florida 33776-1434 Phone 727-593-3100 Fax 727-593-7950 E Mail lpk @ fdn.com January 9, 2006 FEDERAL COMMUNICATIONS COMMISSION Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 Re: REQUEST FOR CONFIDENTIALITY FCC ID:RFK-CBAHP800 Model HP-800 Dear Sir/ Madam: Due to Janizary Holdings, Inc. requirement for proprietary information in conjunction with a Manufacturing Agreement with Leon Paul Kass LLC which is in conjunction with a License to use specific patented technology from Motorola, Inc. in the development and production of this unit, we are requesting to hold the following exhibits as Confidential. 1. Block Diagram 2. Parts List 3. Schematic drawing 4. Theory of operation Thank you very much Regards Leon Paul Kass

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 November 21, 2005 RE: FCC ID: RFK-CBAHP800_ATCB002958 Attention: Leon Paul Kass I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please provide the Operational description for the device. 2. Please provide the external photos for the device. 3. Please provide the internal photos for the device. 4. Please provide the manual for the device. As soon as the above items are provided, the final review can begin. Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 November 29, 2005 RE: FCC ID: RFK-CBAHP800_ATCB002958 Attention: Leon Paul Kass I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please note that the 731 says the device is a part 22 amplifier operating in the frequency range between 824 – 849MHz and 869 – 894MHz. However, the test report shows the frequency range of 806- 824MHz and 851-869MHz. The data seems to be for a part 90 frequency range. Please explain and please correct any documentation needed to reflect the actual rule part for which certification is being sought. 2. Please note that the 731 says the FCC ID number is RFK-CBAHP800, but the report says it is RFK-CBAHPNEX. This could be the reason item one is a problem. Please correct all documentation to reflect the same FCC ID number. 3. Please note that the MPE calculations are for FCC ID RFK-CBAHPNEX. Please provide an rf exposure MPE report for FCC ID RFK-CBAHP800. 4. Additional questions may arise based on the response to the above items.. Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

FCC ID: RFK-CBAHP800 95 RF Exposure – MPE Calculations Input Transmitter Power: 202 mW Antenna Gain: 15 dB Cable loss: 1.13 dB @ 824 – 894 MHz Frequency range: 824-894 MHz Assumptions 1. A single ¼ wavelength radiating antenna is assumed. 2. Closest exposure distance is assumed to be 30 cm (50 cm recommended in manual) FCC ID: RFK-CBAHP800 96 RF Exposure – MPE Calculations Calculations The following results shall be assumed to be accurate for the far-field only. These predictions will over-estimate power density in the near–field. Based on the use of a ¼ wavelength radiator, a distance of 20 cm is considered to be in the far-field for all cases. For the purposes of these calculations a distance of 30cm was used. The actual distance as specified in the user manual is 50cm. 30cm represents the worst case configuration assuming an incorrect installation. S = PG/4*PI*R 2 @ 824 – 894 MHz P is 202 mW G is 13.87dB (Antenna gain – loss) or 10 (13.87/10) or 24.378 R is 30 cm S = 0.436 mW/cm 2 For Occupational/Controlled Exposure From 300 to 1500 MHz, power density limit is f/300 mW/cm 2 @ 824 MHz, power density limit is 2.75 mW/cm 2 for 6 minutes. For General Population/Uncontrolled Exposure From 300 to 1500 MHz, power density limit is f/1500 mW/cm 2 @ 824 MHz, Power density limit is 0.55 mW/cm 2 for 30 minutes. Conclusion: Meets MPE limits

FCC ID: RFK-CBAHP800 1 Application for Certification For an RF amplifier Janizary Holdings Inc. 5380 Sterling Center Drive Westlake Village, CA 91361 RF amplifier FCC ID: RFK-CBAHP800 REPORT # RV58129A-002 This report was prepared in accordance with the requirements of the FCC Rules and Regulations Part 2, Subpart J, 2.1031 through 2.1057, and Part 22 and in accordance with Industry Canada Radio Standards Specification RSS-131 for Zone Enhancers and any other applicable sections of the rules as indicated herein. Prepared By: DNB Engineering, Inc. 5969 Robinson Avenue Riverside, Ca 92503-8620 Industry Canada Lab Code: IC 4738 6 Jan 2006 FCC ID: RFK-CBAHP800 2 TEST LAB PERSONNEL Test Performed by: Date Signature Thomas Elders 17 May 2005 APPROVAL Management Approval Date Signature Les Payne Sr. Engineering Manager 17 May 2005 REVISION APPROVAL Management Approval Date Signature Les Payne Sr. Engineering Manager 6 Jan 2006 Original report RV58129A-001 Dated 17 May 2005 Revised Report RV58129A-002 Dated 6 Jan 2006 FCC ID: RFK-CBAHP800 3 TABLE OF CONTENTS Section Title Sheet # Test Lab Personnel and Approvals 2 Table of Contents 3 Table of Figures 4 1.0 ADMINISTRATIVE DATA 5 1.1 Certifications and Qualifications 5 1.2 Measurements and Repeatability Information 5 1.3 Test Methodology 6 1.4 Test Equipment 6 1.5 Deviations 6 1.6 Test Description 7 Note: Paragraph numbers in this report follow the application section numbers found in the FEDERAL COMMUNICATIONS COMMISSION Rules and Regulations, Part 2, Subpart J for Certification of electronic equipment. 2.1033 (C) (1) Application for Certification 8 2.1033 (C) (2) FCC Identifier 9 2.1033 (C) (3) Installation and Operating Instructions (Service manual) 9 2.1033 (C) (4) Type of Emissions 9 2.1033 (C) (5) Frequency Range 9 2.1033 (C) (6) Operating Power 9 2.1033 (C) (7) Maximum Power Allowed in Applicable part(s) of the Rules 9 2.1033 (C) (8) Final RF amplifier Input Power Characteristics 9 2.1033 (C) (9) Tune Up Procedure 9 2.1033 (C) (10) Schematic Diagram and Circuit Description 10 2.1033 (C) (11) Equipment Identification Plate 10 2.1033 (C) (12) Equipment Photographs (Internal) 10 2.1033 (C) (12) Equipment Photographs (External) 10 2.1033 (C) (13) Digital Modulation Techniques 10 2.1033 (C) (14) Test Data 10 Test Set-Up 11-12 2.1046 (RSS-131 cl4.3) Measurement of RF Power Output 13-19 2.1049 (RSS-131 cl4.4) Measurement of Occupied Bandwidth 20-40 2.1051 (RSS-131 cl4.5) Spurious Emissions at Antenna Terminals 41-77 2.1053 Measurement of Field Strength of Spurious Radiation 78-84 Conducted Emissions 85-87 Radiated Emissions 88-89 2.1055 (RSS-131 cl4.5) Measurement of Frequency Stability 90 2.1057 Frequency Spectrum to be Investigated 91 RF Exposure 92-93 Appendix A Photographs 94-98 FCC ID: RFK-CBAHP800 4 TABLE OF FIGURES Figure 1 : Test Equipment 6 Figure 2 : Test Result Summary 10 Figure 3 : Test Set Up Block Diagram 12 Figure 4 : Block Diagram Radiated Emissions 12 Figure 5 : Output Power Plots 14 Figure 6 : Occupied Bandwidth / Modulation Characteristic Plots 21 Figure 7 : Antenna Conducted Spurious Plots 42 Figure 8 : Radiated Spurious Tabular Data 79 Figure 9 : Unintentional Conducted Emissions 86 Figure 10 : Unintentional Radiated Emissions 89 Appendix A : Photos 95 FCC ID: RFK-CBAHP800 5 1.0 ADMINISTRATIVE DATA 1.1 Certifications and Qualifications I certify that DNB Engineering, Inc conducted the tests performed in order to obtain the technical data presented in this application. Also, based on the results of the enclosed data, I have concluded that the equipment tested meets or exceeds the requirements of the Rules and Regulations governing this application. 1.2 Measurement Repeatability Information The test data presented in this report has been acquired using the guidelines set forth in FCC Part 2.1031 through 2.1057, and Part 22, also included in this report is compliancy data for Industry Canada RS-131 for Zone Enhancers. The test results presented in this document are valid only for the equipment identified herein under the test conditions described. Repeatability of these test results will only be achieved with identical measurement conditions. These conditions include: The same test distance, EUT Height, Measurement Site Characteristics, and the same EUT System Components. The system must have the same Interconnecting Cables arranged in identical placement to that in the test set-up, with the system and/or EUT functioning in the identical mode of operation (i.e. software and so on) as on the date of the test. Any deviation from the test conditions and the environment on the date of the test may result in measurement repeatability difficulties. All changes made to the EUT during the course of testing as identified in this test report must be incorporated into the EUT or identical models to ensure compliance with the FCC regulations. C. L. Payne III (Para. 1.1) Sr Engineering Manager DNB Engineering, Inc. Tel. (951) 637-2630 Fax (991) 637-2704 E-mail [email protected] FCC ID: RFK-CBAHP800 6 1.3 Test Methodology The tests were performed in accordance with FCC Part 2 Subpart J, 2.1031 through 2.1057, 15, and 22, Industry Canada RSS-131 on a sample of the production model. 1.4 Test Equipment FIGURE 1: TEST EQUIPMENT Description Manufacturer M/N S/N Cal Date Test Used On Signal Generator Agilent E4432B GB40051213 09/24/05 RF Power Out put, Emissions Lim, Cond Spur, Rad Spur, CE Signal Generator Marconi 2024 112231/034 02/02/05 RF Power Out put, Emissions Lim, Cond Spur, Rad Spur, CE Spec Analyzer Display H/P 85662A 259101-1 01/10/06 RF Power Out put, Emissions Lim, Cond Spur, Rad Spur, CE Spectrum Analyzer H/P 8566B 259101-2 01/10/06 RF Power Out put, Emissions Lim, Cond Spur, Rad Spur, CE Spec Analyzer Display H/P 85662A 2318A05282 8/14/05 RE Spectrum Analyzer H/P 85680B 2049A01403 6/2/05 RE Quasi-Peak Adapter H/P 85650A 2043A00184 6/2/05 RE Bicon Antenna H/P 85650A 2043A00184 6/2/05 RE Log Antenna AH Systems SAS-200/540 524 12/26/05 R…

Text truncated - open the document above for the full version.

FCC ID: RFK-CBAHP800 31 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 4 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Uplink – CDMA – Mid Channel – 836.5 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 32 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 4 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Uplink – CDMA – Hi Channel – 848.3 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 33 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 3 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Lo Channel – 869.2 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 34 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 3 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Mid Channel – 881.5 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 35 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 3 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Hi Channel – 893.8 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 36 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 3 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Lo Channel – 869.2 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 37 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 3 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Mid Channel – 881.5 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 38 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 3 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Hi Channel – 893.8 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 39 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 4 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – CDMA – Lo Channel – 869.7 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 40 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 4 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – CDMA – Mid Channel – 881.5 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 41 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Occupied Bandwidth DNB Job Number: 58129 Date: 4 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – CDMA – Hi Channel – 893.3 MHz Description: Plots – Top = Input / Bottom = Output Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 42 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Inter-Modulation DNB Job Number: 58129 Date: 3 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Uplink – CW – Input – Lo / Near Lo / Hi channels Description: Plots: Top = Allowable Band / Bottom = 100MHz span Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 43 FIGURE 6: OCCUPIED BANDWIDTH 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Inter-Modulation DNB Job Number: 58129 Date: 3 Jan 2006 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Uplink – CW – Input – Lo / Near Lo / Hi channels Description: Plots: Top = Allowable Band / Bottom = 100MHz span Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 44 2.1051 Spurious Emissions at Antenna Terminals (IC RSS-131 Clause 4.4) Definition: Conducted Spurious Emissions are emissions at the antenna terminals on a frequency or frequencies which are outside an occupied band sufficient to ensure transmission of information of required quality for the class of communication desired. The reduction in the level of these spurious emissions will not affect the quality of the information being transmitted. Conducted Spurious Emissions shall be attenuated below the maximum level of the carrier frequency in…

Text truncated - open the document above for the full version.

FCC ID: RFK-CBAHP800 61 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 8 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Uplink – CDMA – Hi Channel – 848.3 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 62 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 8 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Uplink – CDMA – Hi Channel – 848.3 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 63 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Lo Channel – 869.2 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 64 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Lo Channel – 869.2 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 65 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Mid Channel – 881.5 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 66 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Mid Channel – 881.5 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 67 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Hi Channel – 893.8 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 68 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – GSM – Hi Channel – 893.8 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 69 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Lo Channel – 869.2 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 70 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Lo Channel – 869.2 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 71 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Mid Channel – 881.5 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 72 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Mid Channel – 881.5 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 73 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Hi Channel – 893.8 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 74 Figure 7: Conducted Spurious Emissions at Antenna Terminals, Uplink. 5969 Robinson Avenue Riverside, CA 92503 (951) 637-2630 FAX (951) 637-2704 Antenna Conducted Spurious DNB Job Number: 58129 Date: 7 Apr 2005 Customer: Janizary Holdings Inc Model Number: CB-HP-800 Serial Number: RF amplifier Downlink – TDMA – Hi Channel – 893.8 MHz Description: Conformance Standards [X] IC RSS-131 [X] FCC Part 22 FCC ID: RFK-CBAHP800 75 Figure 7: Conducted Spurious Emi…

Text truncated - open the document above for the full version.