RGR-46KMC2Marine Audio

Installation Please read the instruction carefully before operating the unit Installation ATTENTIONS OF INSTALLATION 1.This player should be installed by professional technician. 2. Please read the instruction and operation of equipment carefully before installing. 3. Make sure to connect other wires before power connection. 4. To avoid short circuit. Please make sure all the exposed wire are insulating. 5. Please fix all the wires after installation. 6. Please make connection to the player accordingly to this instruction manual. Wrong connection may cause damage. 7. This player only fit for 12V DC device and please make sure your car belongs to this kind of cathode grounding electrical system. 8. Please connect the wires rightly. Wrong connection will cause malfunction or damage the electrical system. Installation WIRING CONNECTION 1. This player can only be used by the 12V DC cathode grounding electrical system. 2. Don’t connect the terminals of the battery until the player is absolutely with well erection joint. 3. Please make sure to connect the yellow wire to the positive of the battery(+). 4. When change the fuse. Please make sure the specifications are same. 5. Using good quality speaker with 4-8 ohm can result in the best effect of the equipment. KEY FUNCTION LOCATION OF KEYS 1 POWER/SOURCE button 1.MENU button 2.PRESETS button 4 Seek up button 5 PAUSE button 6.Seek down button KEY FUNCTION Key functions table Keys Acti on Radio USB AUX BT Stand by PWR /SRC Short Source change Source change Source change Source change Power on Long Power off Power off Power off Power off Power on PRE SET S Short Preset (+encoder) File search (+encoder) / / / Long Manual save(+encoder) RPT one/RPT all/RDM on/RDM off Test mode（5 Seconds） / / MEN U Short BT (pair/conn)-BEEP (on/off)-LOUD(on/off) -AREA(USA/EUR) BT (pair/conn)-BEEP (on/off)-LOUD(on/off)- AREA(USA/EUR) BT (pair/conn)- BEEP(on/off)-LOU D(on/off)-AREA (USA/EUR) BT (pair/conn)- BEEP(on/off)-LOU D(on/off)-AREA (USA/EUR) / Long BT (pair/conn)-BEEP (on/off)-LOUD(on/off) -AREA(USA/EUR) BT (pair/conn)-BEEP (on/off)-LOUD(on/off)- AREA(USA/EUR) BT (pair/conn)- BEEP(on/off)-LOU D(on/off)-AREA (USA/EUR) BT (pair/conn)- BEEP(on/off)-LOU D(on/off)-AREA (USA/EUR) / << Short Seek down Previous file / Previous file / Long Manual turn down RF / RF / >> Short Seek up Next file / Next file / Long Manual turn up FF / FF / >II Short Mute on/off Play/Pause Mute on/off Play/Pause / Long Reset (10 Sec) Reset (10 Sec) Reset (10 Sec) Reset (10 Sec) / Enco der Rotar y Volume up/down Volume up/down Volume up/down Volume up/down / SEL Short BAS-TRE-BAL-FAD- EQ BAS-TRE-BAL-FAD- EQ BAS-TRE-BAL- FAD-EQ BAS-TRE-BAL- FAD-EQ / Long BAS-TRE-BAL-FAD- EQ BAS-TRE-BAL-FAD- EQ BAS-TRE-BAL- FAD-EQ BAS-TRE-BAL- FAD-EQ / OPERATION Turn on/off the unit Press button to turn on the unit. When the unit is on. Press and hold it for 2 seconds to turn off the unit. Sound and setting adjustment Shortly press VOL knob for the audio menu: BAS-TRE-BAL-FAD-EQ Shortly press VOL knob for the setting menu: BT (pair/conn)-BEEP (on/off)-LOUD(on/off)-AREA(USA/EUR) In each item rotate the VOL k nob to set them. BT(pair/conn): When paired with the mobile. Choosing “BT PAIR” then press VOL knob to dis- connect the Bluetooth and prepare to pair another mobile. In this moment, choosing “BT CONN” then press VOL knob to reconnect the Bluetooth. BEEP (on/off): Turn on/off the beep sound. LOUD (on/off): Turn on/off the loudness function. AREA (USA/EUR): Choose America or Europe region frequency. Display the clock or information Shortly press CLK button to show the clock or information. Reset the unit Press and hold button for 10 seconds to reset the unit. Note: When RESET function is activated, all the memory will be lost. Radio Operation Receive a radio station Press SOURCE button to select FM/AM mode. Shortly press /button to receive the desired radio station. Press and hold /button for manual tuning the frequency. Manually store station & recall preset station Receiving a desired station. Press and hold the PRESETS button for 2 seconds. It shows “SAVE P1”. Rotating VOL knob to select P1~18 then press VOL button. The station will be saved. Listening to Saved Radio Memory Shortly press the PRESETS button then rotating VOL knob to select the presets. USB Operation When an USB driver inserted to the unit, the unit will play the MP3/WMA file automatically. If an USB drive is already inserted in the unit. Keep pressing SOURCE button shortly until the USB mode display appears. Select file Press /button to skip to next/previous file. Hold /button to fast forward or fast reverse. OPERATION Play/Pause Pressbutton to pause/playing the file. Search song Press PRESETS button to select song search mode. Rotating VOL knob to enter numbers. Press VOL knob to play. RPT(ONE/ALL)/RDM(ON/OFF) When playing MP3/WMA, Press and hold PRESETS button for 2 seconds, It shows “RPT ONE”. Rotating VOL knob to select RPT one/RPT all/RDM on/RDM off. AUX IN operation Connecting the signal to the R/L IN connecter behind the unit. Then pressing SOURCE button to switch to AUX mode. Bluetooth Operation Pairing On mobile phone, select the Bluetooth item searching the Bluetooth device. “KMC KICKER” should appear in the list, select “KMC KICKER” and then input password “0000” If it needs a password. When successful paired, the BT mark will be solid (not flashing). Bluetooth Audio Press SOURCE button to switch to BT mode. It will play a song of your mobile phone automatically. Press key to pause/play the song. Press button to select next/previous song. Other operation please reference the Key functions table above. IC Statement: This device complies with Industry Canada’s licence‐exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme au…

Text truncated - open the document above for the full version.

Stillwater Designs & Audio ,Inc Agent Authorization Letter 2020-03-25 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen Huaxia Testing Technology Co., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Name: Joe Hobart Position: R&D Electronics Manager Company Name: Stillwater Designs & Audio ,Inc Address: 3100 N Husband Street, Stillwater OK 74075 United States of America Tel / Fax 405-533-7505/ 405-624-0033 E-Mail: [email protected]

Declaration statement Letter 2020-03-25 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Declaration statement Letter To Whom It May Concern: We hereby declare that (FCC ID: RGR-46KMC2) fulfill the requirements of 47 CFR Part 15C Section 15.247(g) & 15.247(h). Compliance for section 15.247(g) According to Bluetooth Core Specification, the Bluetooth system transmits the packet with the pseudorandom hopping frequency with a continuous data and the short burst transmission from the Bluetooth system is also transmitted under the frequency hopping system with the pseudorandom hopping frequency system. Compliance for section 15.247(h) According to Bluetooth Core specification, the Bluetooth system incorporates with an adaptive system to detect other user within the spectrum band so that it individually and independently to avoid hopping on the occupied channels. According to the Bluetooth Core specification, the Bluetooth system is designed not have the ability to coordinated with other FHSS System in an effort to avoid the simultaneous occupancy of individual hopping frequencies by multiple transmitter. Please contact me if there is any information you may need. Sincerely, Name: Joe Hobart Position: R&D Electronics Manager Company Name: Stillwater Designs & Audio ,Inc Address: 3100 N Husband Street, Stillwater OK 74075 United States of America Tel / Fax 405-533-7505/ 405-624-0033 E-Mail: [email protected]

Stillwater Designs & Audio ,Inc Long Term Confidentiality Request Letter 2020-03-25 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (FCC ID: RGR-46KMC2) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - e.g. Block diagram - e.g. SCH - e.g. Operational Description required to be submitted with this application be permanently withheld from public review. The above documents are company proprietary information that could never get into the possession of your competition. Please contact me if there is any information you may need. Sincerely, Name: Joe Hobart Position: R&D Electronics Manager Company Name: Stillwater Designs & Audio ,Inc Address: 3100 N Husband Street, Stillwater OK 74075 United States of America Tel / Fax 405-533-7505/ 405-624-0033 E-Mail: [email protected]

Model difference letter 2020,03,25 Dear MET Reviewer, This is a new Application from Stillwater Designs & Audio ,Inc KMC2, KMC3 are identical in interior structure, electrical circuits, components and appearance. Only different in color of appearance and model name Thank you for your cooperation! Yours sincerely, Signatory: Name: Joe Hobart Position: R&D Electronics Manager Company Name: Stillwater Designs & Audio ,Inc Address: 3100 N Husband Street, Stillwater OK 74075 United States of America Tel / Fax 405-533-7505/ 405-624-0033 E-Mail: [email protected]

Test Model No.:KMC2 Model No.: KMC3

Marine Audio Model No.: KMC2 FCC ID: RGR-46KMC2 ISED: 11078A-KMC2 Power Supply: DC12V Manufacturer: Eastern Partner Limited This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Marine Audio Model No.: KMC3 FCC ID: RGR-46KMC2 ISED: 11078A-KMC2 Power Supply: DC12V Manufacturer: Eastern Partner Limited This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Shenzhen Huaxia Testing Technology Co., Ltd 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China Telephone: +86-755-26648640 Fax: +86-755-26648637 Website: www.cqa-cert.com Report Template Version: V04 Report Template Revision Date: 2018-07-06 RF Exposure Evaluation Report The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s) tested. Without written approval of CQA, this report can’t be reproduced except in full. Report No. : CQASZ20200200098E-02 Applicant: Stillwater Designs & Audio ,Inc Address of Applicant: 3100 N Husband Street, Stillwater OK 74075 United States of America Equipment Under Test (EUT): EUT Name: Marine Audio Model No.: KMC2, KMC3 Test Model No.: KMC2 Brand Name: KICKER FCC ID: RGR-46KMC2 Standards: 47 CFR Part 1.1307 47 CFR Part 2.1093 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2020-03-02 Date of Test: 2020-03-02 to 2020-03-26 Date of Issue: 2020-03-26 Test Result : PASS* *In the configuration tested, the EUT complied with the standards specified above Tested By： (Tom Chen) Reviewed By: (Aaron Ma) Approved By: ( Jack Ai) Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200200098E-02 Page:2 of 6 1 Version Revision History Of Report Report No. Version Description Issue Date CQASZ20200200098E-02 Rev.01 Initial report 2020-03-26 Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200200098E-02 Page:3 of 6 2 Contents Page 1 VERSION .....................................................................................................................................................................2 2 CONTENTS .................................................................................................................................................................3 3 GENERAL INFORMATION .......................................................................................................................................4 3.1 CLIENT INFORMATION ................................................................................................................................................4 3.2 GENERAL DESCRIPTION OF EUT ................................................................................................................................4 4 SAR EVALUATION ....................................................................................................................................................5 4.1 RF EXPOSURE COMPLIANCE REQUIREMENT ..............................................................................................................5 4.1.1 Standard Requirement .................................................................................................................................5 4.1.2 Limits ..............................................................................................................................................................5 4.1.3 EUT RF Exposure .........................................................................................................................................6 Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200200098E-02 Page:4 of 6 3 General Information 3.1 Client Information Applicant: Stillwater Designs & Audio ,Inc Address of Applicant: 3100 N Husband Street, Stillwater OK 74075 United States of America Manufacturer: Eastern Partner Limited Address of Manufacturer: 1002, 10/F, 189 Des Voeux Road, Central Hong Kong 3.2 General Description of EUT Product Name: Marine Audio Model No.: KMC2, KMC3 Test Model No.: KMC2 Trade Mark: KICKER Hardware Version: 20200104 REV:06 Software Version: 20200106U2 Operation Frequency: 2402MHz~2480MHz Bluetooth Version: V4.0 Modulation Technique: Frequency Hopping Spread Spectrum(FHSS) Modulation Type: GFSK, π/4DQPSK Transfer Rate: 1Mbps/2Mbps Number of Channel: 79 Hopping Channel Type: Adaptive Frequency Hopping systems Product Type: Mobile Portable Fix Location Test Software of EUT: FCCAssist 2.4 (manufacturer declare ) Antenna Type: PCB antenna Antenna Gain: -0.58dBi Power Supply: DC12V Model No.: KMC2, KMC3 Only the model KMC2 was tested, since the electrical circuit design, layout, components used and internal wiring were identical for the above models, with difference being appearance and model name. Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200200098E-02 Page:5 of 6 4 SAR Evaluation 4.1 RF Exposure Compliance Requirement 4.1.1 Standard Requirement According to KDB447498D01 General RF Exposure Guidance v06 4.3.1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. 4.1.2 Limits The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 17 The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200200098E-02 Page:6 of 6 4.1.3 EUT RF Exposure Measurement Data GFSK mode Test channel Peak Output Power (dBm) Tune up tolerance (dBm) Maximum tune-up Power (dBm)…

Text truncated - open the document above for the full version.

Shenzhen Huaxia Testing Technology Co., Ltd 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China Telephone: +86-755-26648640 Fax: +86-755-26648637 Website: www.cqa-cert.com Report Template Version: V04 Report Template Revision Date: 2018-07-06 Test Report The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s) tested. Without written approval of CQA, this report can’t be reproduced except in full. Report No. : CQASZ20200200098E-01 Applicant: Stillwater Designs & Audio ,Inc Address of Applicant: 3100 N Husband Street, Stillwater OK 74075 United States of America Equipment Under Test (EUT): EUT Name: Marine Audio Model No.: KMC2, KMC3 Test Model No.: KMC2 Brand Name: KICKER FCC ID: RGR-46KMC2 Standards: 47 CFR Part 15, Subpart C Date of Receipt: 2020-03-02 Date of Test: 2020-03-02 to 2020-03-26 Date of Issue: 2020-03-26 Test Result : PASS* *In the configuration tested, the EUT complied with the standards specified above Tested By： (Tom Chen) Reviewed By: (Aaron Ma) Approved By: (Jack Ai) Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200200098E-01 Page:2 of 78 1 Version Revision History Of Report Report No. Version Description Issue Date CQASZ20200200098E-01 Rev.01 Initial report 2020-03-26 Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200200098E-01 Page:3 of 78 2 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 (2013) PASS AC Power Line Conducted Emission 47 CFR Part 15, Subpart C Section 15.207 ANSI C63.10 (2013) N/A Conducted Peak Output Power 47 CFR Part 15, Subpart C Section 15.247 (b)(1) ANSI C63.10 (2013) PASS 20dB Occupied Bandwidth 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013) PASS Carrier Frequencies Separation 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013) PASS Hopping Channel Number 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013) PASS Dwell Time 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013) PASS Pseudorandom Frequency Hopping Sequence 47 CFR Part 15, Subpart C Section 15.247(b)(4)&TCB Exclusion List (7 July 2002) ANSI C63.10 (2013) PASS Band-edge for RF Conducted Emissions 47 CFR Part 15, Subpart C Section 15.247(d) ANSI C63.10 (2013) PASS RF Conducted Spurious Emissions 47 CFR Part 15, Subpart C Section 15.247(d) ANSI C63.10 (2013) PASS Radiated Spurious emissions 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 (2013) PASS Restricted bands around fundamental frequency (Radiated Emission) 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 (2013) PASS N/A: The EUT powered by DC, So Not Applicable Model No.: KMC2, KMC3 Only the model KMC2 was tested, since the electrical circuit design, layout, components used and internal wiring were identical for the above models, with difference being appearance and model name. Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200200098E-01 Page:4 of 78 3 Contents Page 1 VERSION .................................................................................................................................................................. 2 2 TEST SUMMARY .................................................................................................................................................... 3 3 CONTENTS .............................................................................................................................................................. 4 4 GENERAL INFORMATION ................................................................................................................................... 5 4.1 CLIENT INFORMATION .......................................................................................................................................... 5 4.2 GENERAL DESCRIPTION OF EUT .......................................................................................................................... 5 4.3 ADDITIONAL INSTRUCTIONS................................................................................................................................. 7 4.4 TEST ENVIRONMENT ............................................................................................................................................ 8 4.5 DESCRIPTION OF SUPPORT UNITS ......................................................................................................................... 8 4.6 STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................. 9 4.7 TEST LOCATION ................................................................................................................................................. 10 4.8 TEST FACILITY ................................................................................................................................................... 10 4.9 ABNORMALITIES FROM STANDARD CONDITIONS ............................................................................................... 10 4.10 OTHER INFORMATION REQUESTED BY THE CUSTOMER ...................................................................................... 10 4.11 EQUIPMENT LIST ................................................................................................................................................ 11 5 TEST RESULTS AND MEASUREMENT DATA .............................................................................................. 12 5.1 ANTENNA REQUIREMENT ................................................................................................................................... 12 5.2 CONDUCTED PEAK OUTPUT POWER ................................................................................................................... 13 5.3 20DB OCCUPY …

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup 1.1 Radiated Emission 9KHz~30MHz: 30MHz~1GHz: Above 1GHz: