RMZ-BTS40Bluetooth Speaker

BTS-05 TCH Module User Manual 20150408 V1.2 User’s Manual Model: BTS-40 MW232 Shower Bluetooth Speaker With FM Radio (Splash-Proof) Transmit music to your shower with our Shower Bluetooth Speaker. Splashes proof design allows for all-round bathroom usage. The hanging window design makes hanging in the shower quick and easy. BTS-05 TCH Module User Manual 20150408 V1.2 1. Important Don’ts • Do not place naked flames, such as lighted candles on or near the product. • Do not place objects filled with liquids, such as vases on or near the product. • Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or vibration. • Do not keep or store this product in wet conditions for long period. • Do not push foreign objects into the slots or holes in the product. • Do not attempt to open this product yourself. There are no user serviceable parts inside. • Do not allow children access to plastic bags. Safety Instructions • Before using this product, read and follow all warnings and instructions. • This product is not intended for use by young children. Young children should be properly supervised. • This product is intended for household use only and not for commercial or industrial use. • No naked flame sources, such as lighted candles, should be placed on the product. • Ventilation should not be impeded by covering ventilation openings with items such as newspapers, table cloths, curtains and the like. • Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty. We, suggests retaining the packaging in case for future transport of the product. WARNING: • Never remove the casing of this apparatus. • Never place this apparatus on the other electrical equipment. Caution for Splash-proof • This unit has been constructed to resist mild steam and light splashes from the shower or bath only. It should never be operated under running water and under no circumstances it should never be fully immersed in water. • This unit has rubber seals to minimize the risk of moisture getting inside. However, do not immerse it in water since permanent damage to the electrical and mechanical parts will result. BTS-05 TCH Module User Manual 20150408 V1.2 2. Getting Start A. Outlook and Controls: 1. Hanging Window (For Lanyard / Hand Up) 2. Button (Power Off / On) 3. Charging LED (Red) 4. Button (Volume Down) 5. Button (Previous, Tune Down) 6. Button (Play / Pause, Hand-Free, Radio Mode / Channel Select) 7. Button (Next, Tune Up) 8. Button (Volume Up) 9. Mode LED (Power / Bluetooth Mode, Radio Mode) 10. Speaker 11. MIC (for Handset) 12. Rubber Seals (Splashes Proof Cover) 13. Micro USB (Inside Splash Proof cover) B. About the speaker rechargeable battery: 1. This Bluetooth Speaker has an internal, non–user-replaceable battery. For best results, the first time you use this Bluetooth Speaker, let it charge for about 2 - 3 hours or until the charging indicator color is changed to Green from RED which show you the battery is fully charged. 2. For maintain the battery life and performance, if speaker isn’t used for BTS-05 TCH Module User Manual 20150408 V1.2 a while, the battery might need to be recharged. Recharge the battery at least once per month. C. To recharge the built-in rechargeable battery: You can charge the Bluetooth Speaker’s battery in two ways: 1. Connect Bluetooth Speaker to the Computer. Or, 2. Use the USB power charger. (not included) D. Connection and Charging: 1. Open the Rubber Seal Cover (12) and connects the Bluetooth Speaker’s Micro USB connector (13) with the Computer’s USB port through USB cable (supplied). 2. The charging LED (3) turns ON in red light. (make sure that the computer is turned ON) 3. The charging LED (3) will switch to green light when it’s fully changed. 4. Disconnect the USB cable when it is done. Charging LED Function Item Mode Light Status 1. No DC power input: LED light OFF 2. In Charging: Light On in red color 3. Charge Completed: Light color from red switch to green E. Power ON/OFF and Pairing: 1. Press and hold (2) button for 2 ~ 3 seconds to turn “ON” the Bluetooth speaker, a series of tones will sound and the mode LED indicator (9) will light up with blinking blue (half second once) simultaneously. It is in Bluetooth searching and pairing mode. 2. Then, activate the Bluetooth function in your mobile Bluetooth device (such as Mobile Phone, MID or Personal Computer); the mobile device will enter to Bluetooth searching mode automatically, if not, tap the relate selection to manually enter to searching mode. (refer to your mobile device’s manual when necessary) 3. Your mobile Bluetooth device should show “MRX-MW232” in list, and then select it for pairing. Waiting for some seconds, then you will see connected message as shown on your mobile Bluetooth device and a series of tones will sound from the Bluetooth speaker when they connected and paired. 4. For some mobile Bluetooth devices, you may need to input “0000” as pairing password. Once devices paired, the Bluetooth Speaker will beeps twice and the mode LED stays steadily ON with flashing in 2 seconds once, the device is in paired. (pairing need time will depend on the difference type / brand of device be used) BTS-05 TCH Module User Manual 20150408 V1.2 5. Now, you can start to music play on your Bluetooth device when the device is in paired and show connected. 6. To turn “OFF” the Bluetooth Speaker, press and hold (2) button for 2 ~ 3 seconds, a series of tones will sound, the mode LED (9) and the device will turn OFF simultaneously. Power & Mode Indicator Function: Item Mode Description Light Status 1. Power OFF Light OFF. 2. Power ON At Bluetooth searching mode: Blue light On & blinking (half second once) At Bluetooth paired mode Blue light On & blinking (2 seconds once) At Radio mode Red light On Note: In…

Text truncated - open the document above for the full version.

DATE : May 25, 2015 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: RMZ-BTS40 Product Name: Bluetooth Speaker Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operational Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this May 25, 2015 Agency agreement expiration date: Usually Give 8 - 12 Months By: Judy Zhu Signature Printed Title: Manager On behalf of : Richen Industrial Co.,Ltd Telephone: 0755-83268139

Outside view Outside view Outside view

Mark Location: Label Location

ILE Bluetooth Speaker Model No.: BTS-40 Internal Battery: 3.7V Input: 5 V FCC ID: RMZ-BTS40 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Inside view Inside view Inside view Inside view

RF Exposure Applicable Standard According to §1.1307(b)(5), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. This is a Portable device. The Section 4.3.1 and Appendix A of KDB447498 D01 V05 was used as the guidance. Calculation Result (Worse Case): [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] =1.48/5 * 1.57= 0.46, this value is less than 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. The SAR measurement is not necessary.

2013-9-27 V2.0 FANG JIA QUN 2 of Sheet name: C B A D Size: A3 Approved By: Checked By: Drawn By: Drawing No: Version: Date: Date: Date: Sheet: 1 1 2 3 4 5 6 6 5 4 3 2 1 MAIN File name: A B C D POWER ATS2805_MAIN MAIN USB CORE COM4 SD_CLK SD_CMD SD_DATA COM0 PA_EN COM2 COM1 COM3 IR SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 SPI_MI SPI_CLK LINE_DECT SPI_CS SPI_MO SPI_SCK SPI_MOSI SPI_MISO SPI_SS MEMORY BAT3.7V ON/OFF MP1 AVRL161A6R8GTA RZ2 2.2K RZ3 2.2K 1 BT_ANT AZ1 1 GPIO_A19 2 SPI_MISO 3 SPI_MOSI 4 SPI_CLK 5 GPIO_B19 6 USBDM 7 USBDP 8 AOUTL 9 AOUTR 10 AGND 11 LINEINR 12 LINEINL 13 MICIN 14 FMINL 15 FMINR 16 AVCC 17 LRADC1 18 VCC 19 GND 20 BT_ANT 21 FM_ANT 22 GND 23 VBAT 24 DC5V 25 RTCVDD 26 ON/OFF 27 LOSCI 28 LOSCO 29 GPIO_B13 30 GPIO_B2 31 GPIO_B1 32 GPIO_B8 33 GPIO_A16 34 GPIO_A8 35 I2CSDA 36 I2CSCL 37 GPIO_A12 38 GPIO_B4 39 GPIO_A10 40 GPIO_A11 41 GND 42 GPIO_A30 43 GPIO_A29 44 GPIO_A28 45 GPIO_A27 46 GPIO_A26 47 GPIO_A25 48 GPIO_A24 49 GPIO_A23 UZ1 ATS2805A_BT 1 CS- 2 SO 3 WP- 4 GND 5 SI 6 SCK 7 HOLD- 8 VCC UN1 MX25L8006E CN1 104 K1 ON/OFF MJ1 AVRL161A6R8GTA 1 2 3 4 5 6 7 8 9 USB1 USB_MICRO_2DIP D3 1N5819 ANT ANT1 FM ANT R33 330R R6 330R MP4 AVRL161A6R8GTA MP5 AVRL161A6R8GTA MP6 AVRL161A6R8GTA 1 3 2 D2 LED-3 1 M1 MK 1 M2 MK 1 M3 MK 1 M4 MK 1 M5 MK 1 M6 MK 1 M7 MK 1 M8 MK 1 3 2 D4 LED-3 B1 B+ B2 B- RZ1 1K R3 0R R4 0R RZ4 10K RZ5 20K 1 SP+3 TP-U 1 2 YZ2 32768Hz VBAT GND USBDP USBDM GND VBUS LOSCO LOSCI VCC I2CSCL I2CSDA FMANT BL_GND VBAT DC5V RTCVDD ON_OFF LOSCI LOSCO GPIO_B13 GPIO_B2 GPIO_B1 GPIO_B8 GPIO_A16 GPIO_A8 I2CSDA I2CSCL GPIO_A26 GPIO_A25 GPIO_A23 FMINR GPIO_A19 SPI_MISO SPI_MOSI SPI_CLK GPIO_B19 USBDM USBDP AOUTL AOUTR AGND FMINR FMINL MICIN BL_GND FMINL AVCC LRADC1 VCC GPIO_A12 GPIO_B4 GPIO_A10 GPIO_A11 GPIO_A27 GPIO_A28 GPIO_A29 GPIO_A30 GPIO_A24 VCC VCC GND GND GPIO_A19 SPI_MISO SPI_MOSI SPI_CLK VCC DC5V VCC GPIO_A11 GPIO_A12 ON_OFF GPIO_A10 GND USBDM USBDP# USBDM# VBUS# GND# USBDP GPIO_A30 AGND BL_GND GPIO_B4 D C B A File name: AUDIO&CONNECTOR 1 2 3 4 5 6 6 5 4 3 2 1 2 Sheet: Date: Date: Date: Version: Drawing No: Drawn By: Checked By: Approved By: A3 Size: 2015-3-31 D A B C Sheet name: of 2 FANG JIA QUN V2.0 ATS2805_MAIN AUDIO&CONNECTOR MIC The AVCC pull-up resistance should be placed near the MCU. μ±K7 K5ͬʱ° ́ʱÍê³ÉRESET¹¦ÄÜ ¹¦·Å RESET + CJ1 100uF CM1 474 CM3 224 MM1 AVRL161A6R8GTA K2 PLAY/STOP/MODE K3 VOL+ K4 VOL- K5 PREV CM2 106 D1 1N5819 C62 104 K7 NEXT MM2 AVRL161A6R8GTA RM1 1K RM2 3.6K RJ6 30K % RJ7 3.6K % RJ8 7.5K % R7 6.8K C1 474 C8 NC C9 NC R11 4.7K R12 NC C3 104 R16 15K TP3 TP4 R41 4.7R/1206 C2 105 C4 474 R1 6.8K C5 104 CM4 106 MM3 AVRL161A6R8GTA MM4 AVRL161A6R8GTA R56 10K R57 10K R71 1K R72 1K R73 1K R74 1K 2 1 3 Q10 3906 2 1 3 Q1 3906 R14 10K R15 0R C11 225 1 SHDN- 2 BYP 3 IN+ 4 IN- 8 VO+ 7 GND 6 VDD 5 VO- U6 NS4160 R2 15K C6 104 RJ1 2.2K SP+1 SP+2 VBAT VBAT VBUS MICIN AVCC LRADC1 AVCC AOUTL AOUTR VBAT VCC RTCVDD ON_OFF GPIO_A16 GPIO_A23 GPIO_A8 VCC AGND AGND AGND

ISO/IEC17025Accredited Lab. Report No.: FCC 1504226 File reference No.: 2015-05-26 Applicant: Richen Industrial Co., Ltd. Product: Bluetooth Speaker Model No.: BTS-40 Trademark: ILE Test Standards: FCC Part 15 Subpart C, Paragraph 15.247 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10&FCC Part 15 Subpart C, Paragraph 15.247 regulations for the evaluation of electromagnetic compatibility Approved By Jack Chung Manager Dated: May 25, 2015 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Room 512-519, 5/F., East Tower, Building 4, Anhua Industrial Zone, Futian District, Shenzhen, Guangdong, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No: FCC1504226 Page 2 of 81 Date: 2015-05-26 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement˖ The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:1999 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 899988 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.:899988. IC-Registration No.: IC5205A-02 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration No.: IC 5205A-02. Report No: FCC1504226 Page 3 of 81 Date: 2015-05-26 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration.................................................................................................... 5 1.6 Test Uncertainty.................................................................................................5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test...................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating Condition....................................................................................9 5.5 Conducted E…

Text truncated - open the document above for the full version.

Conducted Emission Test Setup: Radiated Emission Test Setup: