RMZ-BTS68Shower Bluetooth speaker

BTS-18_20150408 V1.0 1 User’s Manual Model: BTS-68 MW234 Bluetooth Speaker With FM Radio (Splash-proof) Transmit music to your shower with our Shower Bluetooth Speaker. Splashes proof design allows for all-round bathroom usage. The hanging window design makes hanging in the shower quick and easy. BTS-18_20150408 V1.0 2 1. Important Don’ts • Do not place naked flames, such as lighted candles on or near the product. • Do not place objects filled with liquids, such as vases on or near the product. • Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or vibration. • Do not keep or store this product in wet conditions for long period. • Do not push foreign objects into the slots or holes in the product. • Do not attempt to open this product yourself. There are no user serviceable parts inside. • Do not allow children access to plastic bags. Safety Instructions • Before using this product, read and follow all warnings and instructions. • This product is not intended for use by young children. Young children should be properly supervised. • This product is intended for household use only and not for commercial or industrial use. • No naked flame sources, such as lighted candles, should be placed on the product. • Ventilation should not be impeded by covering ventilation openings with items such as newspapers, table cloths, curtains and the like. • Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty. We, suggests retaining the packaging in case for future transport of the product. WARNING: • Never remove the casing of this apparatus. • Never place this apparatus on the other electrical equipment. Caution for Splash-proof • This unit has been constructed to resist mild steam and light splashes from the shower or bath only. It should never be operated under running water and under no circumstances it should never be fully immersed in water. • This unit has rubber seals to minimize the risk of moisture getting inside. However, do not immerse it in water since permanent damage to the electrical and mechanical parts will result. BTS-18_20150408 V1.0 3 2. Getting Start A. Outlook and Controls: Item Control 1 Button (ON / OFF) 2 Charge LED Indicator (White) 3 Bluetooth LED Indicator (White) 4 Button (Previous, Volume down / Preset station down) 5 Button (Next, Volume up / Preset station up) 6 Button (Hand Free, FM Mode) 7 Button (Play / Pause, Radio auto search / Radio Mute) 8 MIC Hole 9 Rubber Seal Cover (Splash-proof cover) 10 Micro USB socket (Under Rubber Seal Cover) 11 Vacuum Cupule 12 Speaker 1 2 3 4 5 6 7 8 10 9 11 12 BTS-18_20150408 V1.0 4 B. About the speaker rechargeable battery: 1. This Bluetooth Speaker has an internal, non–user-replaceable battery. For best results, the first time you use this Bluetooth Speaker, let it charge for about 2 ~ 3 hours or until the “Charge LED (2)” Indicator light from On to off which show the battery is fully charged. 2. For maintain the battery life and performance, if speaker isn’t used for a while, the battery might need to be recharged. Recharge the battery at least once per month. C. To recharge the built-in rechargeable battery: You can charge the Bluetooth Speaker’s battery in two ways: 1. Connect Bluetooth Speaker to the Computer. Or, 2. Use the USB power charger. (not included) D. Connection and Charging: 1. Open the “Rubber Seal Cover (10)” and connects the Bluetooth Speaker’s “Micro USB socket (9)” with the Computer’s USB port through the USB cable. 2. The “Charge LED (2)” Indicator will turn On, the battery is in charging. 3. The “Charge LED (2)” Indicator will turn Off when it’s fully charged. 4. Disconnect the USB cable when it is done. Charging LED Function Item Mode Light Status 1. No DC power input: LED light Off 2. In Charging: Light On 3. Charge Completed: Light Off E. Power ON/OFF and Pairing: 1. Press and hold the “ (1)” button for 2 ~ 3 seconds to turn On the device, a series of tones will sound and the “Bluetooth LED (3)” indicator will light up with blinking. 2. Then, activate the Bluetooth function in your mobile Bluetooth device (such as Mobile Phone, MID or Personal Computer); the mobile device will enter to Bluetooth searching mode automatically, if not, tap the relate selection to manually enter to searching mode. (refer to your mobile device’s manual when necessary) 3. Your mobile Bluetooth device should show “MRX-MW234” in list, and then select it for pairing. Waiting for some seconds, then you will see connected message as shown on your mobile Bluetooth device when they connected and paired. 4. For some mobile Bluetooth devices, you may need to input “0000” as pairing password. BTS-18_20150408 V1.0 5 5. However, if pairing is successful, the “Bluetooth LED (3)” indicator will slow blinking each 3 ~ 4 seconds once. 6. Now, you can start to music play from the mobile device by it music player program. 7. Press and hold the “ (1)” button to turn Off the device when it is not in use. Power & Mode Indicator Function: Item Mode Description Light Status 1. Power OFF Light Off 2. Power ON At Bluetooth searching mode: light On & blinking (half second once) At Bluetooth paired mode light On & blinking (3~4 seconds once) At Radio mode light On & blinking At Radio auto search & preset mode Light blinking fast Note: In some circumstances, the Bluetooth connection may break / disconnected; such as some strong interference, beyond the connection distance or object moving in between both Bluetooth devices. However, most of devices can be reconnected in some seconds automatically, but in experience some of device may need to reconnect it by using the Bluetooth device’s list menu manually. Besides, since there have many Bluetooth versions could be installed into difference type/brand of PCs, and also connect metho…

Text truncated - open the document above for the full version.

DATE : May 25, 2015 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: RMZ-BTS68 Product Name: Shower Bluetooth Speaker Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operational Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this May 25, 2015 Agency agreement expiration date: Usually Give 8 - 12 Months By: Judy Zhu Signature Printed Title: Manager On behalf of : Richen Industrial Co.,Ltd Telephone: 0755-83268139

Outside view Outside view Outside view

Mark Location: Label Location

ILE Shower Bluetooth Speaker Model No.: BTS-68 Internal Battery: 3.7V Input: 5 V FCC ID: RMZ-BTS68 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Inside view Inside view Inside view

RF Exposure Applicable Standard According to §1.1307(b)(5), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. This is a Portable device. The Section 4.3.1 and Appendix A of KDB447498 D01 V05 was used as the guidance. Calculation Result (Worse Case): [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] =1.44/5 * 1.57= 0.45, this value is less than 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. The SAR measurement is not necessary.

ISO/IEC17025Accredited Lab. Report No.: FCC 1504227 File reference No.: 2015-05-26 Applicant: Richen Industrial Co., Ltd. Product: Shower Bluetooth Speaker Model No.: BTS-68 Trademark: ILE Test Standards: FCC Part 15 Subpart C, Paragraph 15.247 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10&FCC Part 15 Subpart C, Paragraph 15.247 regulations for the evaluation of electromagnetic compatibility Approved By Jack Chung Manager Dated: May 26, 2015 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Room 512-519, 5/F., East Tower, Building 4, Anhua Industrial Zone, Futian District, Shenzhen, Guangdong, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No: FCC1504227 Page 2 of 80 Date: 2015-05-26 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement˖ The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:1999 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 899988 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.:899988. IC-Registration No.: IC5205A-02 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration No.: IC 5205A-02. Report No: FCC1504227 Page 3 of 80 Date: 2015-05-26 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration.................................................................................................... 5 1.6 Test Uncertainty.................................................................................................5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test...................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating Condition....................................................................................9 5.5 Cond…

Text truncated - open the document above for the full version.

Conducted Emission Test Setup: Radiated Emission Test Setup: