RNERF09150TRXInternet Bridge

This device complies with part 15 of the FCC rules and RSS-210 of IC rules subject to the following two conditions: (1) This device may NOT cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

DATE :2011-7-13 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: RNERF09150TRX Product Name: Internet Bridge Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 2011-8-2 By: Victor Mak Signature Printed Title: Project Manager On behalf of : Chaney Instrument Co. Telephone:852-35829826

CHANEY INSTRUMENT CO. DATE ：2011-8-08 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Name: Neutron Engineering Inc. Address: No.3, JinShaGang 1 st Road, ShiXia, DaLang Town City: Dong Guan Country: China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Company name: CHANEY INSTRUMENT CO. Address: Rm 1102-3,Enterprise Square One, Tower 3, No.9, Sheung Yuet Road, City: Kowloon Bay, Kowloon Country: Hong Kong, China Dated this 2011-8-08 Agency agreement expiration date: Usually Give 8 - 12 Months By: Victor Mak Signature Printed Title: Project Manager On behalf of : ChANEY INSTRUMENT CO. Telephone: 852-35829826

Neutron Engineering Inc. Project No.: 1107C191 Page 2 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 2 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 3 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 3 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 4 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 4 of 10 1107C191 1107C191

Neutron Engineering Inc. Project No.: 1107C191 Page 5 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 5 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 6 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 6 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 7 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 7 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 8 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 8 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 9 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 9 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 10 of 10 1107C191 1107C191 Neutron Engineering Inc. Project No.: 1107C191 Page 10 of 10 1107C191 1107C191

Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 1 of 40 FCC/IC Radio Test Report FCC ID: RNERF09150TRX IC: 6608A-RF09150TRX This report concerns (check one) : Original Grant Copy Report Issued Date : Aug. 02, 2011 Project No. : 1107C191 Equipment : Internet Bridge Model Name : 09150TRX Applicant : Chaney Instrument Co. Address : Rm 1102-3, Enterprise Square One, Tower 3, No.9 Sheung Yuet Road, Kowloon bay, Kowloon, Hong Kong, China Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Jul. 22, 2011 Date of Test: Jul. 22, 2011 ~ Aug. 01, 2011 Testing Engineer : (Ivan Cao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 2 of 40 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutron shall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 3 of 40 Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 9 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 3.4 DESCRIPTION OF SUPPORT UNITS 11 4 . EMC EMISSION TEST 12 4.1 CONDUCTED EMISSION MEASUREMENT 12 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 12 4.1.2 MEASUREMENT INSTRUMENTS LIST 12 4.1.3 TEST PROCEDURE 13 4.1.4 DEVIATION FROM TEST STANDARD 13 4.1.5 TEST SETUP 13 4.1.6 EUT OPERATING CONDITIONS 13 4.1.7 TEST RESULTS 14 4.2 RADIATED EMISSION MEASUREMENT 16 4.2.1. FIELD STRENGTH OF FUNDAMENTAL EMISSIONS MEASUREMENT LIMIT 16 4.2.2. MEASURING INSTRUMENTS AND SETTING 16 4.2.3 RADIATED EMISSIONS MEASUREMENT 17 4.2.4. DWELL TIME OF PERIODIC OPERATION MEASUREMENT 18 4.2.5. MEASUREMENT INSTRUMENTS LIST 20 4.2.6. TEST PROCEDURE 20 4.2.7. DEVIATION FROM TEST STANDARD 20 4.2.8. TEST SETUP 21 4.2.9. EUT OPERATING CONDITIONS 21 4.3. TEST RESULTS (9KHz-30MHz) 22 4.3.1 TEST RESULTS(BETWEEN 30 – 1000 MHz) 22 4.4 TEST RESULTS (ABOVE 1000 MHz) 28 5. 20dB SPECTRUM BANDWIDTH MEASUREMENT 34 5.1.MEASURING INSTRUMENTS AND SETTING 34 5.2.TEST PROCEDURES 34 5.3. TEST SETUP LAYOUT 34 Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 4 of 40 Table of Contents Page 5.4. TEST DEVIATION 34 5.5. EUT OPERATION DURING TEST 34 5.6. TEST RESULT 35 6. TIMING TESTING 36 6.1.MEASURING INSTRUMENTS AND SETTING 36 6.2.TEST PROCEDURES 36 6.3. TEST SETUP LAYOUT 36 6.4. TEST DEVIATION 36 6.5. EUT OPERATION DURING TEST 36 6.6. TEST RESULT 37 7. EUT TEST PHOTO 39 Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 5 of 40 1. CERTIFICATION E q u i p m e n t : Internet Bridge Trade Name : ACURITE Model Name. : 09150TRX A p p l i c a n t : Chaney Instrument Co. Date of Test : Jul. 22, 2011 ~ Aug. 01, 2011 T e s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.231)/ ANSI C63.4 : 2003; Canada RSS-210:2010 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FICP-1-1107C191) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 6 of 40 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C (15.231) Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS RSS-210 2.7 Table 5 15.209 & 15.231(e) Radiated Spurious EmissionPASS RSS-210 A1.1.3 15.231(c) 20dB Occupied Bandwidth Measurement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 7 of 40 2.1 TEST FACILITY The test facilities used to collect the test data in this report is DG-C02/DG-CB03 at the location of No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China.523792 Neutron's test firm number for FCC 319330 Neutron's test firm number for IC 4428B-1 2.2 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multip…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 38 of 39 7. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 38 of 39 7. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 39 of 39 Radiated Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1107C191 Page 39 of 39 Radiated Measurement Photos