RNIP738575-HPS2 Wireless Controller Host

How to use: Step 1: Insert the controller's receiver into the Player 1 slot Note: - Do not insert the controller's receiver into a memory card slot. - Switch off the console before inserting the controller's receiver. Once the receiver is inserted you may turn on your console. Step 2: When the receiver is first plugged into the console, the LED is OFF. Once the controller has detected the receiver, the LED on the receiver will turn ON. The controller is now ready to use. Note: When using more than one wireless controller, you can only plug one receiver in at a time. When the LED lights up on the first receiver you can then plug in the second wireless receiver into the next available controller port. Force Connection to a designated Controller and Receiver: Forcing the connection to a designated controller and receiver can be achieved by following the steps listed below: a) Press the FC button on the receiver - the LED on the receiver starts to blink. b) Press and hold the Select and L3 button simultaneously on the controller. The LED of the receiver stops to blink and lights up. The force connection is complete and you are ready to play. c) Controller's receiver Battery Replacement: - Open the battery compartment door. - Insert the batteries as marked on the bottom of the battery compartment. - Close the battery compartment door. You are now ready to use your wireless controller. Note: - For longer playing time, use Alkaline batteries. - Do not mix fresh and used batteries. This will reduce the controller's transmitting and receiving distance and may cause the product to malfunction. - Rechargeable batteries can be used with this product (rechargeable batteries are not included). - Dispose of used batteries according to the battery manufacturer's instructions. Thank you for purchasing Hip Gear's 2.4G Wireless Controller for all PlayStation consoles. Please read this manual carefully before use. Features: - Fully compatible with all PlayStation consoles (PS2, PSOne and PSX) - Dual vibration motors - Power on/off selection - Twin analog sticks - Rubber grips - Auto player matching - 10 Meters(30ft) 2.4G RF wireless transmitting & receiving distance - Turbo fire setting - Macro programmable setting - Low power Indicator Button Name for Hip Gear's 2.4G RF PS2 Wireless Controller: a) Controller (front view) b) Controller (top view) PS2 2.4G Wireless Controller compatible with PlayStation, PSone and PlayStation2 TURBO MACRO SELECT START MODE POWER ON/OFF FUNCTION R3 L3 D-PAD FIRE BUTTONS R1 R2 L1 L2 FORCE CONNECTION BUTTON LED L3 Force Connection Button LED Caution: If the controller is left idle for more than 3 minutes the designated connection may be lost. If this happens, simply repeat the steps above. Mode Button: The Mode button is used for selection of Digital or Analog modes. The LED is OFF - Digital The LED is ON - Analog Turbo Fire Setting: Each button of the wireless controller has a built-in Turbo Fire function, simply follow the steps listed below to achieve a Turbo Fire gaming experience: - Press and hold the Turbo Fire button, the Function LED lights up. - Press any button on the controller and the LED will turn off. The Turbo setting is complete. - The Function LED will blink when you press the button which has been set to Turbo Fire. - Repeat the procedure to assign more than one button at a time to a Turbo Fire function. Note: The controller and the receiver must be connected before assigning any Turbo Fire function . To Clear a Turbo Fire: - Press and hold the Turbo Fire button, the Function LED lights up. - Press the button which has been set to Turbo Fire, the LED turns off. - The Turbo Fire is clear, repeat this procedure for any other Turbo Fire cancellations. Macro Setting: The L2, R2, L3 and R3 buttons have built in Macro capabilities. This Macro function allows you to program complicated moves and button combinations into any of the Macro function buttons (L2, R2, L3 and R3). Note: The regular function of the L2, R2, L3 and R3 buttons and Turbo Fire Settings are suspended when the button has a Macro function designated to it - the L3 and R3 buttons are activated by pressing down on the analog sticks. Only when the Macro designated button is cleared will the button resume its regular operation. Clearing the Macro function is explained further in this manual. How to Program a Macro Function: Press Macro button, the Function LED turns ON. - Press the Macro function button you wish to use (L2, R2, L3 or R3). - Input the button combination you wish to designate to the Macro button you have selected. Each combination must be completed within 10 seconds and a maximum of 15 button presses are allowed for each Macro function designation. - Press the Macro button again when the input has been completed, the LED is now OFF. - The Function LED will blink when the Macro function button is activated. - Repeat the same procedure to program other Macro function buttons. To Clear a Macro Setting: - Press the Macro button, the Function LED is now ON. - Press the designated Macro function button that you wish to clear (L2, R2, L3 or R3) - Press the Macro button again, the Macro setting is now clear, and the LED is OFF. Low Power Indication: The Function LED and Mode LED will blink simultaneously when the power is low, replace with new batteries. User Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The FCC require the user to be notified that any changes or modification made to this device that are not expressly approved by Esel International Co., Ltd. may avoid the user's authority to operate the equipment. To comply with FCC RF exposure requirement, this device and its antenna must no be co-located or operating in conjunction with any other antenna or tra…

Text truncated - open the document above for the full version.

ETC Report No.: ET92S-12-003Page A1 of A1 FCC ID: RNIP738575-H ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Outside view 1 of EUT 2. Outside view 2 of EUT

L-738(LM575) 100% R=2.5MM H PS2 Wireless Controller Host D PS2 Wireless Controller Device SCALE:200% R=2.5MM H PS2 Wireless Controller Host D PS2 Wireless Controller Device

2.4GHz RF PS2 Wireless Controller Host (FCC ID: RNIP738575-H) Working Principle 1. It is a 2.4G RF product. It works at the frequency of ISM Band (2.4GHZ). There are up to 79 channels, and the frequency interval between each channel is 1M Hz. 2. Evenly Randomized Frequency Hopping Sequence method is implemented in the RF technology. 3. It works in “Master” Mode. We call it “Host.” The working procedures are: a) When power on, the Host will do the frequency hopping according to a certain sequence, and then send the connection command. b) If there is a Device response, the Host will judge whether it can be permitted to connect. c) If it can be permitted to connect, then send the connection command to build up the connection. d) The Host sends the request command to the Device to get the Axes and Buttons value. e) The Device sends the Axes and Buttons value to the Host. f) The Host will identify the data received and then do the data detection and data correction. g) The Host will save the data received if there is no error. h) The Host judges whether it is required to send Axes and Buttons value to PS2 console. i) If it is required, then send the saved data to PS2 console. j) The Host judges whether there is any Motor command and/or Motor value sent from PS2 console. k) If there is, then the Host will save the received Motor data. l) The Host send Motor commands to the Device, and send the Motor value to the Device. m) Repeat Step e) to Step l)

Rev. No 1.0 FCC Part 15 EMI TEST REPORT of E.U.T. : PS2 Wireless Controller Host MODEL : LM575 FCC ID. : RNIP738575-H for APPLICANT : Esel International Co., Ltd. ADDRESS: Rm 15-17, 5/F, Cardinal Ind, Bldg. No. 17 On Lok Mun St., Fanling, N.T., Hong Kong Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 8 LANE 29, WENMIMG ROAD, LOSHAN TSUN, KWEISHAN HSIANG, TAOYUAN, TAIWAN, R.O.C. Tel:(03)3280026#570~576 Fax:(03)3276188 Report Number : ET92S-12-003 ETC Report No. : ET92S-12-003FCC ID. :RNIP738575-H Rev. No 1.0 TEST REPORT CERTIFICATION Applicant: Esel International Co., Ltd. Rm 15-17, 5/F, Cardinal Ind, Bldg. No. 17 On Lok Mun St., Fanling, N.T., Hong Kong Manufacturer: Eastern Sources Electronics Manufacturer Daji Industrial Zone, Hengshan District, Shipai Town, Dongguan City, Guangdong, China. Description of EUT: a) Type of EUT: PS2 Wireless Controller Host b) Trade Name: Hip Interactive c) Model No.: LM575 d) Power Supply: 6VDC (for PS2 station) 110VAC, 50/60Hz Regulation Applied: FCC Rules and Regulations Part 15 Subpart B & C (2003) I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Issued Date :Nov. 28, 2003 Test Engineer : Approve & Authorized Signer : Signature Win-Po Tsai Manager of EMC Testing Department Electronics Testing Center, Taiwan ETC Report No. : ET92S-12-003FCC ID. :RNIP738575-H Rev. No 1.0 Table of ContentsPage 1 GENERAL INFORMATION .......................................................................................................................1 1.1 Product Description ......................................................................................................................................1 1.2 Characteristics of Device ..............................................................................................................................1 1.3 Test Methodology .........................................................................................................................................1 1.4 Modifiction List of EUT ...............................................................................................................................1 1.5 Test Facility ..................................................................................................................................................1 2 PROVISIONS APPLICABLE ......................................................................................................................2 2.1 Definition ......................................................................................................................................................2 2.2 Requirement for Compliance ........................................................................................................................3 2.3 Restricted Bands of Operation ......................................................................................................................5 2.4 Labeling Requirement...................................................................................................................................5 2.5 User Information ...........................................................................................................................................6 3. SYSTEM TEST CONFIGURATION ..........................................................................................................7 3.1 Justification ...................................................................................................................................................7 3.2 Devices for Tested System............................................................................................................................7 4 RADIATED EMISSION MEASUREMENT ..............................................................................................8 4.1 Applicable Standard......................................................................................................................................8 4.2 Measurement Procedure ...............................................................................................................................8 4.3 Measuring Instrument .................................................................................................................................10 4.4 Radiated Emission Data ..............................................................................................................................11 4.4.1 RF Portion...........................................................................................................................................................11 4.4.2 Other Emission ...................................................................................................................................................14 4.5 Field Strength Calculation ..........................................................................................................................14 4.6 Photos of Radiation Measuring Setup ........................................................................................................18 5 CONDUCTED EMISSION MEASUREMENT ........................................................................................19 5.1 Applicable Standard....................................................................................................................................19 5.2 Measurement Procedure .............................................................................................................................19 5.3 Conducted Emission Data..................................…

Text truncated - open the document above for the full version.

ETC Report No.:ET92S-12-003Sheet 1 of 2 Sheets FCC ID.: RNIP738575-H 4.6 Photos of Radiation Measuring Setup ETC Report No.:ET92S-12-003Sheet 2 of 2 Sheets FCC ID.: RNIP738575-H 5.6 Photos of Conduction Measuring Setup