ROL-ASS21010000Wireless USB Dongle

1 QUETEC SoftGate Wireless AP/Router solution (PCMCIA/PCI/USB interface) User’s Guide ~English version~ ~~ 简册请参简 Version Q3. 0 July2004 http://www.quetec.net Copyright 2004. All Rights Reserved. Document Version: Q3.0 All trademarks and trade names are the properties of their respective owner. 2 COPYRIGHT No part of this Publication may be reproduced, transmitted, transcribed, and stored in retrieval System, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. Copyright@2004 by QUETEC Inc. All rights reserved. All brand and product names mentioned in this manual are trademarks and/or registered Trademarks of their respective holders. 3 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device was tested for typical by stander conditions that may occur during use. To comply with FCC RF exposure requirements a minimum separation distance of 1.5cm must be maintained between the user’s body and the device, including the antenna. Remark: Wireless USB Dongle is limited in Ch1~Ch11 by specified fireware controled in U.S.A. 4 Chapter 1 QUETEC SoftGate Introduction This Chapter provides an overview of the SoftGate AP/Router's features and specifications. Thank you for purchasing the QUETEC SoftGate wireless solution adapter. QUETEC SoftGate is the first AP less series family product to turn the existing computers into a wireless AP. It includes four features (4- in-1): Router, AP, Bridge, and WLAN Client. Users can share PC resources such as files, internet connection, video streaming and multimedia title, instantly without the requirement of preinstall or pre-configure wireless base station. SoftGate is the first technology that truly removes the limitation from wireless base station. 5 1.1 QUETEC SoftGate Features 1.1 z 4 in 1 Device— Integrates Router, AP, Bridge, and Client into your PC/Laptop. z Easy Installation & Expansion—Simple, affordable and flexible solution break through your wireless limitation. z Complete Mobility—Small size, portable wireless base station. z Security—64-bit or 128 bit encryption. z Intelligent device— Auto-detect and configure for client or infrastructure AP. 1.2 QUETEC SoftGate Specifications Standard IEEE802.11b Adapter Type PCMCIA, PCI, MiniPCI, USB Multi Mode Router, AP, Bridge, and Client Modulation Technology DSSS Data Encryption 64/128bit WEP encryption; TKIP (Temporal Key Integrity Protocol) Frequency Band 2.412 ~ 2.462 GHz (US) 2.412 ~ 2.484 GHz (Japan) 2.412 ~ 2.472 GHz (Europe) 2.457 ~ 2.462 GHz (Spain) 2.457 ~ 2.472 GHz (France) Channels 11 (US, Canada), 13 (Europe), 14 (Japan), 2 (Spain), 4 (France) Date Rates & Modulation 11Mbps: CCK 5.5Mbps: CCK 2Mbps: DQPSK 1Mbps:DBSK Media Access Protocol CSMA/CA (Carrier sense multiple access with collision avoidance) Supported OS Windows ME, 2000, XP LED Indicators Power, Link, Activity Receive Sensitivity 11Mbps@-84dBm 5.5Mbps@-86dBm 2Mbps@-91dBm 1Mbps@-93dBm Transmit Output Power Up to 17dBm Operational Voltage 3.3/5V Temperature Operating : -0C to 55C (32F to 131F) Storage : -5C to 70C (23F to 158F) Humidity Operating: 0% to 90% Non-Condensing Storage: 0% to 90% Non-Condensing Certifications FCC, CE, SAR Warranty One year 6 1.3 QUETEC SoftGate Inte…

Text truncated - open the document above for the full version.

61 6.2 WinXP/ - “”, “”, SoftGate . 62 -“”, “” ”” . -“”, “”, SoftGate. -“” , , ,AP,, MAC . “” ,. 63 -“” , SoftGate . - “AP” , , SSID,, SSID.“” ,. ,“ >>>” . 64 -“” ,., , “ICS/Bridge Settings” , . - “MAC ” ,.. “” MAC. 65 - “...”, . - “...” SoftGate. 66 * WinXP WinXp,WinXP . ””””. “ Windows ” , . 67 6.3 Windows 2000/ Windows 2000 WinXP, :(windows 2000 ) - “” “”,“”, . (QUETEC) 68 * Windows 2000-PCMCIA/PCI ,QUETEC. . - “Profile”, . - “Refresh”, /. - “Quick Connect” , . - “Profile”, “Configure”. - “Configuration” , . - “Advance Configuration” Transmit Rate, RTS Threshold, Fragment Threshold. 69 - “Country” , , “Apply” . - “Site Survey”, “Refresh”. 70 * Windows 2000-USB ,. . ””, , (SSID), , . Ad hocInfrastructure , , (SSID), ,. “”. *: -Peer-to-peer (Ad hoc) -Access point (infrastructure) * : - - *(SSID): - * : -. * : - . 71 “”, “” ,SSID, “”. .. * “” . “ ” , . 72 ””. . ””, ,,/. 73 “” ,WEP. , WEP. WEP 40 104,, 513ASCII1026 . , . . 74 QUETEC SoftGate QUETEC SoftGate: 7.1/ , SoftGate. , . 7.2 SoftGate SoftGate, , SoftGate. “ipconfig” SoftGate, , SoftGate. 7.3 SoftGate ICS 75 7.4 SoftGate , , , , , (Filtering), : CSMA/CD MAC ,(1) LLC ; (2) MAC ATM IEEE 802.3 CSMA/CD, IEEE 802.4 Token-Bus, IEEE 802.5 Token-Ring, IEEE 802.6 DQDB, IEEE 802.11 Wireless LAN, IEEE 802.12 100VG AnyLAN, FDDI , LLC (IEEE 802.2) IEEE 802.3 CSMA/CD IEEE 802.11 Wireless 76 , , (Forwarding) (Filtering)(tree), (subnet), IP 140.114.76.0 255.255.255.0, IP 140.114.76.xx 77 QUETEC SoftGate Wireless AP/Router solution (PCMCIA/PCI/USB interface) 简册 www.quetec.net 78 权 内译编从 国权规叙内规 COPYRIGHT No part of this Publication may be reproduced, transmitted, transcribed, and stored in retrieval System, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. Copyright@2004 by QUETEC Inc., All rights reserved. All brand and product names mentioned in this manual are trademarks and/or registered Trademarks of their respective holders. 79 产经过数装测试严规则个这为环 装设备护对设计装设备会产 发频对电讯证装会产 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device was tested for typical by stander conditions that may occur during use. To comply with FCC RF exposure requirements a minimum separation distance of 1.5cm must be maintained between the user’s body and the device, including the antenna. Remark: Wireless USB Dongle is limited in Ch1~Ch11 by specified fireware controled in U.S.A. 80 产绍 节对线点规总览 谢选购发产线络产够 连笔记计线络设备传统缆线 线点线络办弹 线环轻进讯传递应 进资时协维护笔 庞设备费论园办内线络决 线间动让进讯传递线宽带热 时额购线线点贵设备为经帮 备 业节资 络设维护费实现络线络标 81 产 z 线点桥线络 z 线传输标 z 装简动侦测设线点线 z 弹设计数传输 规 标 线传输标 态 务 线点桥线络 调术 扩频术 线频 国 欧 国 频 国欧国 传输调 协议 统 灯号 电连结运 灵 传输输 电压 温 运 储 湿 运 储 认证 产 82 线数态 z z z 83 装总览 装图标 装过数钟 为节宝贵时间开装们议认边装设 备线装装盘计 装认项 ‹ 装须备统 ‹ 预认装顺软浏览连结 ‹ 装装线络请装开 统装员络选择线络标 键关闭装运 84 装 备进装请骤 骤 将装盘装计驱动装 将会启动装灵来请选择装装图开进装 关闭电将计启动计当统 现装灵时请选项将装盘装计驱 动装将会启动装灵来请选择装装图 开进装 骤 将动执装设动当装灵现装讯时 请装灵将继续装动 骤 继续装灵动驱动应装时将 会动将计设为线点 85 装内 检装 开装产请将购产单检对 没损遗况发产应对对 请经销单联络权 装内 • 线络 • 动装盘盘内 o 装 o 册 • 张装 • 产装内条缆线 86 统 请认装计统备 • 计备处 • 内 • 软 • 组 • 驱 87 装说 节说将领软统进线络装 装设 请将请装将 装过旧请将开进装骤 将动装盘驱装装图标会动装 欢画 88 键将会现权声画 权内请继续进装骤请 开装 选择装键进动 议选择进装 装过见统装请进个装 骤 89 装灵将会动执装骤 针对装会装对话 时请将计装灵将会动继续进装骤 90 时装灵将动设为线点 装过将会讯 请键继续装动 请键装骤 备线络计进连结测试强 应该时络单发现 91 装点 装 当统装装过请将 计 请将装时进动 装 关闭电将计装当 灵时请关闭开执装 盘 装 装将设统 须动设连骤将协进设请装 骤将协设 • 选择开设 • 装选项…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

FCC ID Label Location

Page 4 Page 5 Page 6

FCC ID: ROL-ASS21010000 Report No.: RF930713L02 Operational Description This device is a Wireless USB Dongle, which operates in the 2.4GHz frequency spectrum with throughput of up to 11Mbps which CCK technique will be applied.. The transmitter of the EUT is powered by host equipment via a USB interface. The antenna is Chip antenna without connector. The other instruction, please have a look at the users manual.

FCC ID: ROL-ASS21010000 Report No.: SA930713L021Issued: July 23, 2004 SAR TEST REPORT REPORT NO.: SA930713L02 MODEL NO.: ASS2101 RECEIVED: July 22, 2004 TESTED: July 22, 2004 APPLICANT : Astarte Technology Co., Ltd. ADDRESS: 11F, No. 166, Dah-Yeh RD., Peitou 112, Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 32 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: ROL-ASS21010000 Report No.: SA930713L022Issued: July 23, 2004 Table of Contents 1.CERTIFICATION .........................................................................................................3 2.GENERAL INFORMATION..........................................................................................4 2.1 GENERAL DESCRIPTION OF EUT............................................................................4 2.2 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................................5 2.3 GENERAL INOFRMATION OF THE SAR SYSTEM ...................................................5 2.4 GENERAL DESCRIPTION OF THE SPATIAL PEAK SAR EVALUATION .................9 3.DESCRIPTION OF TEST MODES AND CONFIGURATIONS ..................................13 4.DESCRIPTION OF SUPPORT UNITS ......................................................................14 5.TEST RESULTS ........................................................................................................15 5.1 TEST PROCEDURES ...............................................................................................15 5.2 MEASURED SAR RESULT .......................................................................................16 5.3 SAR LIMITS...............................................................................................................17 5.4 RECIPES FOR TISSUE SIMULATING LIQUIDS ......................................................17 5.5 TEST EQUIPMENT FOR TISSUE PROPERTY ........................................................20 6.SYSTEM VALIDATION ..............................................................................................21 6.1 TEST EQUIPMENT ...................................................................................................21 6.2 TEST PROCEDURE .................................................................................................21 6.3 VALIDATION RESULT...............................................................................................24 6.4 SYSTEM VALIDATION UNCERTAINTIES ................................................................25 7.MEASUREMENT SAR PROCEDURE UNCERTAINTIES.........................................26 7.1 PROBE CALIBRATION UNCERTAINTY ...................................................................26 7.2 ISOTROPY UNCERTAINTY......................................................................................26 7.3 BOUNDARY EFFECT UNCERTAINTY .....................................................................27 7.4 PROBE LINEARITY UNCERTAINTY ........................................................................27 7.5 READOUT ELECTRONICS UNCERTAINTY ............................................................27 7.6 RESPONSE TIME UNCERTAINTY...........................................................................28 7.7 INTEGRATION TIME UNCERTAINTY ......................................................................29 7.8 PROBE POSITIONER MECHANICAL TOLERANCE................................................29 7.9 PROBE POSITIONING .............................................................................................30 7.10 PHANTOM UNCERTAINTY ......................................................................................30 7.11 DASY4 UNCERTAINTY BUDGET.............................................................................31 8.INFORMATION ON THE TESTING LABORATORIES ..............................................32 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA APPENDIX B: ADT SAR MEASUREMENT SYSTEM APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION FCC ID: ROL-ASS21010000 Report No.: SA930713L023Issued: July 23, 2004 1. CERTIFICATION PRODUCT : Wireless USB Dongle MODEL NO. : ASS2101 BRAND NAME : Astarte TESTED : July 22, 2004 APPLICANT : Astarte Technology Co., Ltd. TEST ITEM : ENGINEERING SAMPLE STANDARDS : FCC Part 2 (Section 2.1093), FCC OET Bulletin 65, Supplement C (01-01), RSS-102 The above equipment has been tested by Advance Data Technology Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY:, DATE:July 23, 2004 ( Stacy Hsueh) TECHNICAL ACCEPTANCE:, DATE:July 23, 2004 ( Ansen Lei ) APPROVED BY:, DATE:July 23, 2004 (Cody Chang / Supervisor ) FCC ID: ROL-ASS21010000 Report No.: SA930713L024Issued: July 23, 2004 2. GENERAL INFORMATION GENERAL DESCRIPTION OF EUT PRODUCT Wireless USB Dongle MODEL NO. ASS2101 POWER SUPPLY 5.0Vdc powered by host equipment CLASSIFICATION Portable device, production unit MODULATION TYPE BPSK, QPSK, CCK RADIO TECHNOLOGY DSSS TRANSFER RATE 11/9/6/5.5/2/1Mbps FREQUENCY RANGE 2412MHz ~ 2462MHz NUMBER OF CHANNEL 11 MAXIMUN CONDUCTED OUTPUT POWER (FOR CCK) 18.00dBm ANTENNA TYPE Chip antenna with 0dBi antenna gain AVERAGE SAR(1g) ( FOR CCK) 0.0973W/kg DATA CABLE NA I/O PORTS NA ASSOCIATED DEVICES NA NOTE 1. The no…

Text truncated - open the document above for the full version.

Page 1 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA A1: TEST CONFIGURATION Mode 1 The bottom of the EUT to the flat phantom distance 15 mm Page 2 Mode 2 The tip of the EUT to the flat phantom distance 0 mm Page 3 EUT Photo Page 4 Liquid Level Photo 2450MHz D=155mm Date/Time: 07/22/04 11:51:54 Test Laboratory: Advance Data Technology ASS2101 Mode 1 Bottom Ch 1 DUT: Wireless USB Adapter ; Type: ASS2101 ; Test Channel Frequency: 2412 MHz Communication System: 802.11b ; Frequency: 2412 MHz; Duty Cycle: 1:1; Modulation type: CCK Medium: MSL2450 (σ = 1.9036 mho/m, ε r = 50.6142, ρ = 1000 kg/m 3 ) ; Liquid level : 155mm Phantom section: Flat Section ; Separation distance : 15 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1687;Calibrated: 2003/11/24 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2003/8/15 - Phantom: SAM 12; Type: SAM V4.0; Serial: TP 1202 - Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.6 Build 115 Low Channel/Area Scan (7x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 3.19 V/m Power Drift = 0.07 dB Maximum value of SAR = 0.107 mW/g Low Channel/Zoon Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Peak SAR (extrapolated) = 0.204 W/kg SAR(1 g) = 0.0973 mW/g; SAR(10 g) = 0.0508 mW/g Reference Value = 3.19 V/m Power Drift = 0.07 dB Maximum value of SAR = 0.102 mW/g Date/Time: 07/22/04 12:19:08 Test Laboratory: Advance Data Technology ASS2101 Mode 1 Bottom Ch 6 DUT: Wireless USB Adapter ; Type: ASS2101 ; Test Channel Frequency: 2437 MHz Communication System: 802.11b ; Frequency: 2437 MHz; Duty Cycle: 1:1; Modulation type: CCK Medium: MSL2450 (σ = 1.9373 mho/m, ε r = 50.5805, ρ = 1000 kg/m 3 ) ; Liquid level : 155mm Phantom section: Flat Section ; Separation distance : 15 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1687;Calibrated: 2003/11/24 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2003/8/15 - Phantom: SAM 12; Type: SAM V4.0; Serial: TP 1202 - Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.6 Build 115 Middle Channel/Area Scan (7x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 3.39 V/m Power Drift = -0.2 dB Maximum value of SAR = 0.102 mW/g Middle Channel/Zoon Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Peak SAR (extrapolated) = 0.204 W/kg SAR(1 g) = 0.0943 mW/g; SAR(10 g) = 0.0486 mW/g Reference Value = 3.39 V/m Power Drift = -0.2 dB Maximum value of SAR = 0.0979 mW/g Date/Time: 07/22/04 12:46:38 Test Laboratory: Advance Data Technology ASS2101 Mode 1 Bottom Ch 11 DUT: Wireless USB Adapter ; Type: ASS2101 ; Test Channel Frequency: 2462 MHz Communication System: 802.11b ; Frequency: 2462 MHz; Duty Cycle: 1:1; Modulation type: CCK Medium: MSL2450 (σ = 1.9682 mho/m, ε r = 50.5625, ρ = 1000 kg/m 3 ) ; Liquid level : 155mm Phantom section: Flat Section ; Separation distance : 15 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1687; Calibrated: 2003/11/24 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2003/8/15 - Phantom: SAM 12; Type: SAM V4.0; Serial: TP 1202 - Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.6 Build 115 High Channel/Area Scan (7x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 2.73 V/m Power Drift = -0.2 dB Maximum value of SAR = 0.0518 mW/g High Channel/Zoon Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Peak SAR (extrapolated) = 0.109 W/kg SAR(1 g) = 0.05 mW/g; SAR(10 g) = 0.0248 mW/g Reference Value = 2.73 V/m Power Drift = -0.2 dB Maximum value of SAR = 0.0522 mW/g Date/Time: 07/22/04 14:33:20 Test Laboratory: Advance Data Technology ASS2101 Mode 2 Tip Ch 1 DUT: Wireless USB Adapter ; Type: ASS2101 ; Test Channel Frequency: 2412 MHz Communication System: 802.11b ; Frequency: 2412 MHz; Duty Cycle: 1:1; Modulation type: CCK Medium: MSL2450 (σ = 1.9036 mho/m, ε r = 50.6142, ρ = 1000 kg/m 3 ) ; Liquid level : 155 mm Phantom section: Flat Section ; Separation distance : 0 mm (The tip of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1687; Calibrated: 2003/11/24 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2003/8/15 - Phantom: SAM 12; Type: SAM V4.0; Serial: TP 1202 - Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.6 Build 115 Low Channel/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 2.97 V/m Power Drift = -0.2 dB Maximum value of SAR = 0.0226 mW/g Low Channel/Zoon Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Peak SAR (extrapolated) = 0.045 W/kg SAR(1 g) = 0.0213 mW/g; SAR(10 g) = 0.011 mW/g Reference Value = 2.97 V/m Power Drift = -0.2 dB Maximum value of SAR = 0.0221 mW/g Date/Time: 07/22/04 14:33:20 Test Laboratory: Advance Data Technology ASS2101 Mode 2 Tip Ch 6 DUT: Wireless USB Adapter ; Type: ASS2101 ; Test Channel Frequency: 2437 MHz Communication System: 802.11b ; Frequency: 2437 MHz; Duty Cycle: 1:1; Modulation type: CCK Medium: MSL2450 (σ = 1.9373 mho/m, ε r = 50.5805, ρ = 1000 kg/m 3 ) ; Liquid level : 155 mm Phantom section: Flat Section ; Separation distance : 0 mm (The tip of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1687; Calibrated: 2003/11/24 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2003/8/15 - Phantom: SAM 12; Type: S…

Text truncated - open the document above for the full version.

FCC ID: ROL-ASS21010000 Report No.: RF930713L021Issued: July 21, 2004 FCC TEST REPORT REPORT NO.: RF930713L02 MODEL NO.: ASS2101 RECEIVED: June 30, 2004 TESTED: June 30, 2004 ~ July 20, 2004 APPLICANT: Astarte Technology Co., Ltd. ADDRESS: 11F, No. 166, Dah-Yeh RD., Peitou 112, Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 19, Hwa Ya 2nd rd., Kueishan, Taoyuan, Taiwan, R.O.C. This test report consists of 61 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: ROL-ASS21010000 Report No.: RF930713L022Issued: July 21, 2004 Table of Contents 1CERTIFICATION.............................................................................................. 4 2SUMMARY OF TEST RESULTS ..................................................................... 5 2.1MEASUREMENT UNCERTAINTY................................................................... 5 3GENERAL INFORMATION .............................................................................. 6 3.1GENERAL DESCRIPTION OF EUT ................................................................ 6 3.2DESCRIPTION OF TEST MODES .................................................................. 7 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 7 3.4DESCRIPTION OF SUPPORT UNITS ............................................................ 8 3.5 CONFIGURATION OF SYSTEM UNDER TEST.............................................. 9 4TEST TYPES AND RESULTS ....................................................................... 10 4.1CONDUCTED EMISSION MEASUREMENT................................................. 10 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .............................. 10 4.1.2 TEST INSTRUMENTS ................................................................................... 10 4.1.3 TEST PROCEDURES ....................................................................................11 4.1.4 DEVIATION FROM TEST STANDARD ...........................................................11 4.1.5 TEST SETUP................................................................................................. 12 4.1.6 EUT OPERATING CONDITIONS .................................................................. 12 4.1.7 TEST RESULTS (A)....................................................................................... 13 4.1.8 TEST RESULTS (B)....................................................................................... 19 4.2RADIATED EMISSION MEASUREMENT ..................................................... 25 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ................................... 25 4.2.2 TEST INSTRUMENTS ................................................................................... 26 4.2.3 TEST PROCEDURES ................................................................................... 27 4.2.4 DEVIATION FROM TEST STANDARD .......................................................... 27 4.2.5 TEST SETUP................................................................................................. 28 4.2.6 EUT OPERATING CONDITIONS .................................................................. 28 4.2.7 TEST RESULTS (A)....................................................................................... 29 4.2.8 TEST RESULTS (B)....................................................................................... 30 4.2.9 TEST RESULTS ............................................................................................ 32 4.36dB BANDWIDTH MEASUREMENT ............................................................. 35 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT........................................... 35 4.3.2 TEST INSTRUMENTS ................................................................................... 35 4.3.3 TEST PROCEDURE ...................................................................................... 36 4.3.4 DEVIATION FROM TEST STANDARD .......................................................... 36 4.3.5 TEST SETUP................................................................................................. 36 FCC ID: ROL-ASS21010000 Report No.: RF930713L023Issued: July 21, 2004 4.3.6 EUT OPERATING CONDITIONS .................................................................. 36 4.3.7 TEST RESULTS ............................................................................................ 37 4.4MAXIMUM PEAK OUTPUT POWER............................................................. 41 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT.............. 41 4.4.2 TEST INSTRUMENTS ................................................................................... 41 4.4.3 TEST PROCEDURES ................................................................................... 42 4.4.4 DEVIATION FROM TEST STANDARD .......................................................... 42 4.4.5 TEST SETUP................................................................................................. 42 4.4.6 EUT OPERATING CONDITIONS .................................................................. 42 4.4.7 TEST RESULTS ....................................…

Text truncated - open the document above for the full version.