1 CALL HEAR ODU (CH-100/101/104) CALL HEAR IDU (CH-105-IDU) CH-215, CH-315, CH-415 U s e r G u i d e ALERT AND ASSISTANCE SYSTEM Another quality product from E n g l i s h 2 CONTENTS CONTENTS 1 INTRODUCTION 2 Unpacking the Call Unit ODU and Indoor Unit (IDU) 3 DESCRIPTION 4 Call-Hear ODU (CH-100/101/104) 4 Call-Hear IDU (CH-105-IDU) 5 Standard Key (CH-102) 6 Telescopic Key (CH-103) 6 USING CALL-HEAR 7 INSTALLATION 8 Setting up the Call Unit (ODU) 8 Setting up the Indoor Unit (IDU) 9 Pairing the Call Unit (ODU) and the Indoor Unit (IDU) 10 USING CALL-HEAR 11 Testing the Indoor Unit (IDU) 11 Using Call-Hear 11 SYSTEM CONFIGURATION 13 TROUBLESHOOTING & SAFETY 14 GUARANTEE (EU) 15 GUARANTEE (USA) 16 RECYCLING DIRECTIVES 17 INFORMATION 18 3 INTRODUCTION Congratulations on purchasing your CALL-HEAR system. This consists of an Outdoor Unit(s) (ODU) and an Indoor Unit(s) (IDU). The ODU is a large, clear, weather resistant outdoor transmitter which can be stuck onto an entrance door/glass/window not suitable for iron doors. It is activated and will transmit a signal via a bell push, a key or a combination of the two. The person using this will be someone who requires assistance and needs to alert someone of this. The IDU receives the transmitted signal. The IDU will flash and emit an alarm sound in order to alert someone to help the person in need. It is important that you read the instructions below in order to use your CALL-HEAR system to its full potential. Keep this user guide in a safe place for future reference. This guide explains how to use the following: CALL-HEAR ODU with Bell Push and Key – CH-100 CALL-HEAR ODU with Key – CH-101 CALL-HEAR ODU with Bell Push – CH-104 CALL-HEAR IDU – CH-105-IDU CH215 – CH-100 combined with CH-105-IDU 2 2 4 INTRODUCTION CH315 – CH-101 combined with CH-105-IDU CH415 – CH-104 combined with CH-105-IDU Unpacking the Call Unit (ODU) & Indoor Unit (IDU) On unpacking the Call Unit (ODU) you will find the following contents in the box:  1 Call Unit with adhesive tape  1 A23 Battery  2 Fixing Templates  1 Pack of Screws  1 Rear Label  1 User Guide On unpacking the Indoor Unit (IDU) * you will find the following contents in the box:  1 Indoor Unit  4 AA Batteries  1 Stand Please Note: A Mains adapter can be bought as an accessory for the Indoor Unit (IDU). The standard Key (CH-102) or telescopic Key (CH-103) can be bought as an accessory for the Outdoor Unit (ODU). *This guide refers to the Indoor Unit CH-105-IDU, if you have purchased the CH-120, please refer to the User Guide packed in that box. 4 5 DESCRIPTION Call–Hear ODU (CH–100/101/104) 6 DESCRIPTION Call-Hear IDU 6 7 DESCRIPTION Standard Key (CH-102) Telescopic Key (CH-103) open and insert the A23 battery. Ensure correct polarity 8 USING CALL-HEAR Open the two screw covers and undo the two screws (the screw covers must be replaced after the battery has been inserted to ensure that the unit is correctly water resistant.). Slide the battery compartment cover is observed. Slide the battery compartment cover back into position. 9 INSTALLATION Setting up the Call Unit (ODU) Stick the Call Unit onto a door, window, counter, desk etc (not suitable for iron doors) using the supplied strong adhesive tape. Remove the protective paper from the adhesive tape on the back of the Call unit and stick to the required window. Please use the fixing templates provided and line them up precisely – WARNING – THE ADHESIVE USED IS EXTREMELY STRONG. MISTAKES WILL BE DIFFICULT TO RECTIFY. When placing the Call unit on glass (window/door), stick the rear static label in exactly the same position as the front of the Call Unit. The Call Unit can now be used from the other side of the window/door (except CH104). In such case thickness of glass/door should be less then 2 cm. The Call Unit is also ideal for use on counters, desks, reception areas or on wooden posts. For these uses, the Call unit can be fitted with the supplied adhesive tape. If additional security is required there is provision for three screws which can be fitted by opening the three screw covers and insert screws and screw to desired location. 10 10 INSTALLATION Ensure the Call Unit is placed in a location which is easily accessible and useful for a person in need of assistance. For wheelchair users, the ideal height for the Call Unit is 90cm to 100cm from the ground. Setting up the Indoor Unit (IDU) Open the battery compartment and insert the 4 AA batteries supplied. Ensure correct polarity is observed. Close the battery compartment. Alternatively, connect the mains adaptor (not supplied) into the mains power socket then plug the other end into a suitable wall socket. Ensure the Indoor Unit (IDU) is placed in a location where someone will notice the flashing light and hear the alarm in order to go and assist the person in need. The Call-Hear range is approximately 60-80m in free space and approximately 30m where there are walls or other obstructions. 11 INSTALLATION The Indoor Unit (IDU) can either be placed on the supplied stand or wall mounted. To wall mount the Indoor Unit (IDU), drill two holes and insert two screws 96mm apart. Leave about 5 mm of the screw projecting from the wall. Guide the wall mounting apertures at the back of the unit over the screws and slide the Indoor Unit (IDU) downwards. Caution: Ensure there are no electrical lines, water pipes etc. in the wall where the holes are drilled. Turn the Indoor Unit (IDU) on by turning the On/Off Volume Control switch to the On position. Pairing the Call Unit (ODU) and the Indoor Unit (IDU) The Indoor Unit (IDU) should be paired with the Call Unit (ODU). The pairing procedure is as Follows: 1. Press and hold the pairing/testing key of the Indoor Unit (IDU) and the bell push sign of the Call-Unit (CH-1000/CH-104) at the same time. When pairing is complete, the camera flash led will flash twice and a long beep will be heard. 12 14 12 INSTALLATION 2. Press and hold the pairing/testing key of the Indoor U…

Text truncated - open the document above for the full version.

Block Diagram

9 0+] )5$*(($PSOLFDOO( 4( 35,0$7521,;/7' 02'(/ ),/(1$0( 35(3$5(' $33529(' '$7( '$7( 9(56,21180%(57,7/('2&80(17180%(5 6,=( 6+((7 5(9 2) $PSOLFDOO&+ & Power Battery Time-delay circuit Power regulator Transmi ss ion indicat ion circuit MCU RF power amplifier circuit Antenna match ing circuit Time-d elay c ontrol 433.92MHz Switch S1 and/or S2 U1 =EM78P153 X2 LED1 U3=X C6 2 02P502P

External Photos

INTERTEK TESTING SERVICES External Photos FCC ID: RUM-CH100T external photos - 1 of 1

ID Label/Location Info

MODEL: TITLE: BRAND: COUNTRY: Upper Cabinet Color: Print: Bottom Print: DWN DOC NO.: APPROVAL: DATE: REV.: PAGE OF ISSUED DATE: Cabinet Color: .: PRIMATRONIX CH-100 OUTLINE DRAWING Callhear :PMS Blue 282 white&yellow : White Ivyan A1 1 04 Feb PMS Blue 282 ,20 10 Print: White Productname : - CH 100 :Battery23A/12V FCC ID:RUM-CH100T Made in China TM 4 9 . 5 m m 53.8 mm

Internal Photos

INTERTEK TESTING SERVICES Internal Photos FCC ID: RUM-CH100T Internal photos - 1 of 3 Internal Photo - 1 Internal Photo - 2 INTERTEK TESTING SERVICES Internal Photos FCC ID: RUM-CH100T Internal photos - 2 of 3 Internal Photo - 3 Internal Photo - 4 INTERTEK TESTING SERVICES Internal Photos FCC ID: RUM-CH100T Internal photos - 3 of 3 Internal Photo - 5

Schematics

Amplicall CH-100

Test Report

INTERTEK TESTING SERVICES 5 Second Ceasing Transmission Plots FCC ID: RUM-CH100T 5s - 1 of 1

Test Report

INTERTEK TESTING SERVICES Bandwidth Plots FCC ID: RUM-CH100T bw - 1 of 1

Test Report

- The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com TEST REPORT Report Number: HK10120446-1 Application for Original Grant of 47 CFR Part 15 Certification 433.92MHz Transmitter-Remote Device of Door Bell and/or Telephone Ringer Amplifier FCC ID: RUM-CH100T Prepared and Checked by: Approved by: Koo Wai Ip Nip Ming Fung, Melvin Lead Engineer Supervisor March 09, 2011 March 09, 2011 INTERTEK TESTING SERVICES Test Report Number: HK10120446-1 Page 1 of 18 FCC ID: RUM-CH100T GENERAL INFORMATION Applicant Name: Geemarc Telecom International Limited Applicant Address: 1902 Mass Mutual Tower, 38 Gloucester Road, Wan Chai, Hong Kong. FCC Specification Standard: FCC Part 15, October 1, 2009 Edition FCC ID: RUM-CH100T FCC Model(s): CH-100, CH-101, CH-104 Type of EUT: Remote Control Device Description of EUT: 433.92MHz Transmitter-Remote Device of Door Bell and/or Telephone Ringer Amplifier Serial Number: N/A Sample Receipt Date: December 13, 2010 Date of Test: February 10 to March 03, 2011 Report Date: March 09, 2011 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% INTERTEK TESTING SERVICES Test Report Number: HK10120446-1 Page 2 of 18 FCC ID: RUM-CH100T Table of Contents 1.0 Test Results Summary & Statement of Compliance.............................................. 4 1.1 Summary of Test Results ........................................................................................ 4 1.2 Statement of Compliance ........................................................................................ 4 2.0 General Description................................................................................................. 6 2.1 Product Description ................................................................................................. 6 2.2 Test Methodology.................................................................................................... 6 2.3 Test Facility............................................................................................................. 6 3.0 System Test Configuration...................................................................................... 8 3.1 Justification ............................................................................................................. 8 3.2 EUT Exercising Software......................................................................................... 8 3.3 Details of EUT and Description of Accessories........................................................ 9 3.4 Measurement Uncertainty ....................................................................................... 9 4.0 Test Results............................................................................................................ 11 4.1 Field Strength Calculation...................................................................................... 12 4.2 Radiated Emissions............................................................................................... 13 4.2.1 Radiated Emission Configuration Photograph ..................................................... 13 4.2.2 Radiated Emission Data ..................................................................................... 13 4.2.3 Transmitter Duty Cycle Calculation ..................................................................... 13 4.3 Transmitter Bandwidth and 5-Second Transmission .............................................. 16 4.3.1 Measured Bandwidth.......................................................................................... 16 4.3.2 5-Second Transmission Requirement ................................................................. 16 4.4 AC Power Line Conducted Emission ..................................................................... 16 5.0 Equipment List...................................................................................................... 18 Appendix – Exhibits for Application of Certification INTERTEK TESTING SERVICES Test Report Number: HK10120446-1 Page 3 of 18 FCC ID: RUM-CH100T EXHIBIT 1 TEST RESULTS SUMMARY & STATEMENT OF COMPLIANCE INTERTEK TESTING SERVICES Test Report Number: HK10120446-1 Page 4 of 18 FCC ID: RUM-CH100T 1.0 Test Results Summary & Statement of Compliance 1.1 Summary of Test Results Test Items FCC Part 15 Section Results Details see section Antenna Requirement 15.203 Pass 2.1 Radiated Emission Timing Bandwidth 15.231(b) 15.109 15.231(a) 15.231(c) Pass Pass Pass 4.2 4.3.2 4.3.1 Radiated Emission in Restricted Bands 15.205 Pass 4.2 AC Power Line Conducted Emission 15.207 & 15.107 N/A 4.4 Note: Pursuant to FCC Part 15 Section 15.215(c), the 20dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, oth…

Text truncated - open the document above for the full version.

Test Setup Photos

INTERTEK TESTING SERVICES The Worst Case Configuration Photographs – Mode: Transmission FCC ID: RUM-CH100T config photos (radiated emission – doorbell and/or telephone ringer amplifier) - 1 of 1 Radiated Emission – Doorbell and/or Telephone Ringer Amplifier Front View Rear View