RYYEYBMABAComplete Class2 Bluetooth Module

TAIYO YUDEN 1/2 16-Nov.-2007 Ver.0.1 TAIYO YUDEN Confidential & Tentative Bluetooth ® Module EYBMABA (RF+Baseband (Class 2) UART) User’s Manual The Bluetooth ® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by TAIYO YUDEN CO., LTD. is under license. Please note that this users manual should not be provided to end-users. EYBMABA TAIYO YUDEN 2/2 Document constituent list Control name Control No. Document Page Absolute maximum ratings HD-AG-A071044 1/1 Electrical characteristics HD-AE-A071044 1/4- 4/4 Electrical characteristics HD-AE-B071044 1/1 Electrical characteristics HD-AE-C071044 1/11 - 11/11 Electrical characteristics HD-AE-D071044 1/9- 9/9 Outline / Appearance HD-AD-A071044 1/1 Outline / Appearance HD-AD-B071044 1/3- 3/3 Pin Layout HD-BA-A071044 1/2- 2/2 Rev. record Nov.16. 2007> Ver.0.1 APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＭ－ Ａ０７１０４４ （1／1） Control name Absolute maximum ratings 絶対最大定格書 2007. 11.16 TAIYO YUDEN Co., Ltd. １．Maximum rating Item Symbol MIN TYP MAX Unit Condition Supply voltage VDD -0.3 3.6 V Ta=25°C，GND reference Input voltage Vin -0.3 VDD+0.3V ２．Recommendation operating range Item Symbol MIN TYP MAX Unit Condition Operating supply voltage VDD 3.0 3.30 3.6 V Supply voltage ripple and spike noise VDD_rn (30) mV/p-p Note3) Operating temperature range Topr 0 25 70 °C Humidity =40%RH Note1） Storage temperature range Tstg -30 25 85 °C Humidity =40%RH Note2） Note1) Operating temperature range is set to satisfy products electrical characteristics in the short term. In terms of product life cycle when it is used in condition of varying from TYP standard in the long term, please refer to the reliability condition. 動作温度範囲は短期的に製品の電気的特性を満足する温度範囲です。 TYP規格から大きく外れた条件で、長期ご使用の場合の製品寿命につきましては信頼性条件を ご参照願います。 Note2) Storage temperature range is the condition for transportation and storage in temporary. Please keep it under condition of “reference data” (HQ-BA-***) for long-term storage. 保存温度範囲は、輸送時や短期間の保管時の条件です。 長期保管時は、取扱注意要領の条件に従って保管して下さい。 Note3) The Max. is a reference value. The value may change depending on the evaluation. Max.値は参考値となります。今後の検証によって変更になる可能性があります。 APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＥ－ Ａ０７１０４４ （1／4） Control name Electrical characteristics (Digital) 電気的特性書 (Digital) 2007. 11.16 TAIYO YUDEN Co., Ltd. Electrical characteristics DC Specifications The Specification applies for Topr=25 degrees C, VDD=3.3V No. Parameter Condition Symbol Min TypMax Unit Remark 1 Normal supply voltage VDD 3.0 3.3 3.6 V 2 Input low voltage /RESET, VREG_CTL, UART_RX, UART_CTS VIL 0 0.8 V 3 Input High voltage /RESET, VREG_CTL, UART_RX, UART_CTS VIH 2.0 VDD V 4 Output low voltage UART_TX, UART_RTS VOL - 0.4 V Iout =-2mA 5 Output High voltage UART_TX, UART_RTS VOH VDD-0.4 - V Iout=-2mA 6 Peak current Continuous Rx Iccp (60)(180) mA Note 4 7 Average current 1 Sniff mode (Slave only) Icca1 TBD mA Notes 1,3 8 Average current 2 Standby mode Icca2 (13) mA Notes 3, 4 9 Average current 3 Send DM1packet (Master) Icca3 TBD mA Note 3 10 Average current 4 Receive DM1packet (Slave) Icca4 TBD mA Note 3 11 Average current 5 Hold mode (Slave only) Icca5 TBD mA Note 3 12 Average current 6 Park mode (Slave only) Icca6 TBD mA Notes 2,3 13 Average current 7 /Reset Icca7 (8) mA Note 4 14 Average current 8 VREG_CTL OFF Icca8 (0.4) mA Note 4 Notes: 1. Sniff mode parameter. Max interval 0050h Min interval 0010h Attempt 0005h Timeout 0005h 2. Park mode parameter. Max interval 0100h Min interval 0010h 3. The consumption current might fluctuate with the condition of radio communication, host performance and test circuit. 4. The Typ. is a reference value. The value may change depending on the evaluation. 3. 消費電流は、通信状況、HOSTパフォーマンス、検査回路によって変動する可能性があります。 4. Typ.値は参考値となります。今後の検証によって変更になる可能性があります。 APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＥ－ Ａ０７１０４４ （2／4） Control name Electrical characteristics (Digital) 電気的特性書 (Digital) 2007. 11.16 TAIYO YUDEN Co., Ltd. AC Specifications The Specification applies for Topr=25 degrees C, VDD=3.3V No. Parameter Condition SymbolMinTyp Max UnitRemark 1 VDD Rise Time from 0V to 3.0V t1 (2) ms Note 2 2 VDD=3.0V to VREG_CTL High t2 0 ms 3 VREG_CTL= 3.0V to /RESET High t3 0 ms 4 /RESET High to Module Ready t4 (2600) ms Notes 1, 2 5 /RESET High to /RESET Low t5 0 ms 6 /RESET Pulse Width t6 4 us 7 VREG_CTL Pulse Width t7 TBD ms 8 VREG_CTL High to Module Ready t8 (2600) ms Notes 1, 2 9 /RESET Low to VDD Off t9 0 ms 10 VREG_CTL Low to VDD Off t10 0 ms Notes: 1. It may change due to the firmware version. 2. The Typ. is a reference value. The value may change depending on the evaluation. 1. 値は、firmware versionによって変更する可能性があります。 2. Typ.値は参考値となります。今後の検証によって変更になる可能性があります。 APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＥ－ Ａ０７１０４４ （3／4） Control name Electrical characteristics (Digital) 電気的特性書 (Digital) 2007. 11.16 TAIYO YUDEN Co., Ltd. Timing Diagram for Power Up Sequence VDD /RESET UART_I/F t1 t2 t3 t4 Active t6 t7 VREG_CTL t5 Active Active t4 t8 10% 90% VIH VIH VIL VIL VIH VIL VIL VIH APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＥ－ Ａ０７１０４４ （4／4） Control name Electrical characteristics (Digital) 電気的特性書 (Digital) 2007. 11.16 TAIYO YUDEN Co., Ltd. UART Interface AC Specifications The Specification applies for Topr.= 25 degrees C, VDD=3.3V No. Parameter Condition Symbol Min Typ Max Unit Remark 1 RTS Low to RX Data On t1 0 ms 2 RTS High to RX Data Off t2 5 byte Firmware controlled. 3 CTS Low to TX Data On t3 1 us 4 CTS High to TX Data Off t4 1 byte 5 CTS High Pulse Width t5 0 bit Timing Diagram for UART signals <UART Parameters> Item Parameter Baud Rate 115.2kbps (Typ.) Date Bits 8bits Stop Bits 1bit Parity None Flow Control CTS/RTS Note: 10 bits t2 t1 t4 t3 UART_RTS UART_RX UART_CTS UART_TX Stop bit Start bit t5 APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＥ－ Ｂ０７１０４４ （1／1） Control name Electrical characteristics (RF) 電気的特性書 (RF) 2007. 11.16 TAIYO YUDEN Co., Ltd. Electrical characteristics The Specification applies for Topr = 0to +70°C, VDD=3.00 to 3.60V…

Text truncated - open the document above for the full version.

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00-1407) FCC ID: RYYEYBMABA Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. This module has RF shielding with metal case. Refer to external photo. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Using IC has buffered circuit. 3. The modular transmitter must have its own power supply regulation. This Module has its own regulator. Refer to Block diagram. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. Yes, this module use pattern antenna attached with solder. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Yes, this testing is performed by stand-alone configuration. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. The label of this module with its own FCC ID is put on PCB. Exterior label instruction to installer of this module is provided in user manual. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. Instruction for operational requirements is provided in user manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. This module complies with RF exposure requirements and instruction for users is provided in the user manual. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): Jiro Ogiwara Date: 30 th November 2007 Signature:

EYBMABA_ External Photo 1.FRONT VIEW 2.REAR VIEW

APPROVED CHECKED DRAWN DESIGNED Control No. （1／3） Control name Label Information 2007. 11.16 Confiden tial TAIYO YUDEN Co., Ltd. 24.0±0.3 13.8±0.3 XXXX Ver. A 00037AXXXXXX １．Indication Label 1 description (back-side) ラベル1表示内容 (基板側) 1) BD address number ： ０００３７Ａ◇◇◇◇◇◇ (Refer to ｢Instruction for lot number｣) BDアドレス番号 ： ０００３７Ａ◇◇◇◇◇◇（ロット番号解説書参照） 2) Product Lot number ： Four digits (Refer to ｢Instruction for lot number｣) 製造Lot番号 ： ４桁 （ロット番号解説表参照） 3) Version ID ： Ve r. A Version ID ： Ve r. A Material ：ＰＥＴ（ＵＬ９６９） ／ Label color：White ／ Printing ：Black 材質 ：ＰＥＴ（ＵＬ９６９）／ ラベル色 ：白 ／ 印字 ：黒 1) 3) 2) APPROVED CHECKED DRAWN DESIGNED Control No. （2／3） Control name Label Information 2007. 11.16 Confiden tial TAIYO YUDEN Co., Ltd. ２．Indication Label 2 description (front-side ,Two-Layer Label ,Upper Layer ) ラベル2-1表示内容 (ケース側 2層ラベル1枚目表面) 1) Product Number ： EYBMABA 認証型式 ： EYBMABA 2) Industry Canada ID ： 4389B-EYBMABA 3) FCC ID ： RYYEYBMABA 4) JAPAN logo mark ： Specified logo mark 日本電波法ロゴマーク ： 規定ロゴマーク 5) ARIB, Actual indication ： Indicates that this device is “Second Generation Low Power Data Communication System” ARIB 現品表示 ： 「第二世代小電力データ通信システム」であることを表記 6) JAPAN qualification number ： 201WW07215247 日本電波法認証番号 ： 201WW07215247 7) Manufacture (English) ： Taiyo Yuden Co., Ltd. 製造 ： 太陽誘電株式会社 2.4FH12.4FH1 Material ：ＰＥＴ（ＵＬ９６９） ／ Label color：White ／ Printing ：Black 材質 ：ＰＥＴ（ＵＬ９６９）／ ラベル色 ：白 ／ 印字 ：黒 2) 3) 5) 4) 6) 7) 1) APPROVED CHECKED DRAWN DESIGNED Control No. （3／3） Control name Label Information 2007. 11.16 Confiden tial TAIYO YUDEN Co., Ltd. ３．Indication Label 2 description (front-side ,Two-Layer Label ,Lower Layer) ラベル2表示内容 (ケース側 2層ラベル2枚目表面) 1) R&TTE CE mark ： Specified CE mark R&TTE CE表示 ： CE0560 1)

EYBMABA_ Internal Photo 1.FRONT VIEW 2.REAR VIEW

Test Report Report No.: 7171F Page: 2 / 75 Table of Contents Revised Record .....................................................................................................................................................................4 1 Test Report ....................................................................................................................................................................5 2 General Information .....................................................................................................................................................5 2.1 Applicant Information ..........................................................................................................................................5 2.2 Product Description ..............................................................................................................................................5 2.3 Summary of Test and Inspection Result ...............................................................................................................6 2.4 Test Methodology.................................................................................................................................................7 2.5 Test Facility..........................................................................................................................................................7 3 System Test Configuration ...........................................................................................................................................8 3.1 Justification ..........................................................................................................................................................8 3.2 Operating Modes ..................................................................................................................................................9 3.3 Configuration of Tested System .........................................................................................................................10 3.4 List of Accessories and EUT ..............................................................................................................................12 3.5 Interface Cables ..................................................................................................................................................13 3.6 Test Instruments .................................................................................................................................................13 3.7 Special Test Condition........................................................................................................................................13 3.8 Equipment Modifications ...................................................................................................................................13 4 Antenna Requirement.................................................................................................................................................14 5 AC Powerline Conducted Emission ...........................................................................................................................15 5.1 Test Setup ...........................................................................................................................................................15 5.2 Conducted Emission Calculation........................................................................................................................16 5.3 Test Results ........................................................................................................................................................17 6 20dB Bandwidth ..........................................................................................................................................................19 6.1 Test Setup ...........................................................................................................................................................19 6.2 Test Results ........................................................................................................................................................19 7 Carrier Frequency Separation ...................................................................................................................................20 7.1 Test Setup ...........................................................................................................................................................20 7.2 Test Results ........................................................................................................................................................20 8 Number of Hopping Frequency .................................................................................................................................22 8.1 Test Setup ...........................................................................................................................................................22 8.2 Test Results ........................................................................................................................................................22 9 Dwell Time ...................................................................................................................................................................23 9.1 Test Setup ...........................................................................................................................................................23 9.2 Test Results ........................................................................................................................................................23 10 Maximum Peak Output Power ..................................................................................................................................26 10.1 Test Setup .........…

Text truncated - open the document above for the full version.

Test Setup Photos (7171F) Page: 1 / 4 TEST SETUP PHOTOS Applicant : TAIYO YUDEN CO., LTD. Model No. : EYBMABA FCC ID : RYYEYBMABA Test Setup Photos (7171F) Page: 2 / 4 Photos of Tested EUT Test Setup Photos (7171F) Page: 3 / 4 Photos of Test Setup Photos of Conducted Measurement Test Setup Photos (7171F) Page: 4 / 4 Photos of Radiated Measurement Axial Direction: XY-Plane Axial Direction: YZ-Plane Axial Direction: ZX-Plane Axial Direction X Y Z