RYYWYSAGVDX7Wireless LAN Module

Confidential TAIYO YUDEN TAIYO YUDEN WYSAGVDX7 Wireless LAN Module WYSAGVDX7 (IEEE802.11b/g/n) Data Report Please note that this manual should not be provided to end-users. APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＧ－ Ａ１４０００３ （１／８ ） Control name General items 一般事項書 10 Jul. 2014 （１）Scope 適用 This specification (“Specification”) applies to the hybrid IC “WYSAGVDX7” for use Wireless LAN Module (“Product”) manufactured by TAIYO YUDEN CO.,LTD. (“TAIYO YUDEN”) 本仕様書は、太陽誘電株式会社(“弊社”)により製造されるWireless LAN用ハイブリッドIC “WYSAGVDX7” (“本製品”)に適用する。 （２）Description 内 容 ① Part Number : WYSAGVDX7 品 名 : WYSAGVDX7 ② Function : Radio frequency transceiver Module (IEEE802.11bgn standard conformity) 機 能 : 無線通信モジュール（IEEE802.11bgn 規格準拠） ③ Application : DSLR 用 途 : デジタル一眼レフカメラ ④ Structure : Hybrid IC loaded with silicon and Gallium arsenide monolithic semiconductor 構 造 : ガリウムヒ素 モノリシック半導体を用いた混成集積回路 Containment of hazardous substance in this Product *This product conforms to RoHS Directive (2002/95/EC). 本製品内の環境物質含有 *RoHS指令(2002/95/EC)に適合しています。 ⑤ Terminal : Data input-output : 15pin FPC Connector 503566-1500 (MOLEX) 電 極 : データ入出力 : 15ピンFPCコネクタ 503566-1500 (MOLEX) ⑥ Appearance: Label on the bottom side 外 装 : 無外装 基板裏面にラベル貼付 ⑦ Country of origin : China 製造国 : 日本 TAIYO YUDEN CO.,LTD. APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＧ－ Ａ１４０００３ （２／８） Control name General items 一般事項書 10 Jul. 2014 ⑧ Notes : その他 : a. Limitation of Warranty 保証 i) TAIYO YUDEN provide warranties only if the Product is operated under the condition set forth in this Specification. Please note that TAIYO YUDEN shall not be liable for any defect and/or malfunction arising from use of the Product under the terms and conditions other than the operating conditions hereof. In addition when this Product is used under environmental conditions such as over voltage which are not guaranteed, it may be destroyed in short mode. To ensure the security of customer’s product, please add an extra fuse or/and a protection circuit for over voltage. 本製品の保証使用条件は本仕様書の通りです。 本保証条件以外の条件で御使用になった結果発生した不良・不具合につきましては、弊社は責任を負い 兼ねますので御了承下さい。また､過電圧等本保証条件以外の条件で御使用になった場合､ショートモー ドで破壊する場合があります。安全性の確保のために、フューズや過電流保護回路等の追加をお願い致 します。 ii) This Product is designed for use in products which comply with IEEE802.11bgn Specifications. TAIYO YUDEN disclaims and is not responsible for any liability concerning infringement by this Product under any intellectual property right owned by third party in case the customer uses this Product in any product which does not comply with IEEE802.11bgn Specifications (the “non-complying products”). Furthermore, TAIYO YUDEN warrants only that this Product complies with this Specification and does not grant any other warranty including warranty for application of the non-complying products. 本製品はIEEE802.11bgn ,の規格に従って製造された製品であり、本製品の用途がIEEE802.11bgn規 格以外もしくは当該規格に従わない製品への使用の場合、弊社は第三者の知的財産権の侵害に基づ くいかなる責任を負いません。また、弊社は本製品が本仕様書に準拠することのみを保証するもの で、上記IEEE802.11bgn規格外製品への応用についての保証等いかなる保証を行うものではありま せん。 b. Instruction for Use (CAUTION) 使用上の注意事項 i) Because Product is not designed for radiation durability, please refrain from exposing Product to radiation in the use. 本製品は、耐放射線設計をしておりませんので、放射線のストレスを受ける環境下での使用は避 けて下さい。 ii) Communication between this Product and other might not be established nor maintained depending upon radio environment or operating condition of this Product and other products with wireless technology. 本製品と本製品又は他製品の通信は、周囲の電波環境及び機器環境により確立又は維持し難くな ることがあります。 iii) This Product operates in the unlicensed ISM band at 2.4GHz. In case this Product is used around the other wireless devices which operate in same frequency band of this Product, there is a possibility that interference occurs between this Product and such other devices. If such interference occurs, please stop the operation of other devices or relocate this Product before using this Product or do not use this Product around the other wireless devices. 本製品は2.4GHz帯の周波数を使用しています。本製品を本製品と同じ周波数を使用した他の無 線機器の周辺でご使用になりますと、本製品とかかる他の無線機器との間で電波干渉が発生する 可能性があります。電波干渉が発生した場合、他の無線機器を停止するか、本製品の使用場所を 変えるなど電波干渉の生じない環境でご使用下さい。 TAIYO YUDEN CO., LTD. APPROVED CHECKED DRAWN DESIGNED Control No. ＨＤ－ＡＧ－ Ａ１４０００３ （３／８） Control name General items 一般事項書 10 Jul. 2014 iv) This Product mentioned in this Specification is manufactured for use in DSLR. Before using this product in any special equipment (such as medical equipment, space equipment, air craft, disaster prevention equipment), where higher safety and reliability are duly required, the applicability suitability, or fitness for particular purpose of this Product must be fully evaluated by the customer at its sole risk to ensure correct and safety operation of those special equipments. Also, evaluation of the safety function of this Product even for use in general electronics equipment shall be thoroughly made and when necessary, a protective circuit shall be added in design stage, all at the customer’s sole risk. 本仕様書に記載されている本製品は、デジタル一眼レフカメラ用として製造されております。従 って、高度の安全性や信頼性が求められる医療用機器、宇宙用機器、あるいは防災機器等にお使 いになるときには、本製品の適用可能性、相応性、特定目的に対する適合性をお客様の独自の責 任で十分に評価、検討され、御判断下さい。又、一般機器において御使用になる場合にも、お客 様の独自の責任で十分な安全性評価を実施され、必要に応じて設計時に保護回路等を追加してく ださい。 v) Japan Regulatory Information 日本規制情報 This product with a specific antenna is a radio system approved for Type Approval. Please follow the instructions below on designing your product. 本製品は、特定アンテナとの組み合わせにおいて工事設計認証を受けた無線設備です。 御社製品に搭載される場合、下記内容を遵守願います。 a) This module is certified by Type Approval as the device which has SDIO Interface. Please do not use other purposes except that of certified. Please contact TAIYO YUDEN for more details of purposes of this product. 本モジュールの用途は、SDIOインターフェイスを持つ装置として工事設計認証を受けています。 規定されている用途以外の機器へは使用しないで下さい。 用途の詳細につきましては、弊社までお問い合わせ願います。 b) Please notify clearly below sentences, on your product or in the product manual. 御社製品あるいはマニュアルに下記文言を明示願います。 This product has a radio system which was approved as a radio station in a low power data communication system based on the Radio Law. Name of the radio system: 001-A03958 本製品には、電波法…

Text truncated - open the document above for the full version.

Measurement data of antenna Measured in Satimo Stargate system at TAIYO YUDEN R &D CENTER. Frequency [MHz] @2400 @2450 @2500 Matching circuit constant Peak gain [dBi] 3-plane TX-H 0.2 0.6 0.3 Appearance and coordinates definition TX-V 0.6 0.9 0.1 0.6 0.9 0.3 Average gain [dBi] 160MHz @ VSWR<2 XY-plane TX-H -4.1 -4.1 -5.0 Frequency characteristic 270MHz @ VSWR<3 TX-V -18.3 -17.0 -18.2 Plus(H,V) -3.9 -3.9 -4.8 YZ-plane TX-H -13.7 -14.7 -15.7 TX-V -0.6 -0.6 -1.2 Plus(H,V) -0.4 -0.4 -1.1 ZX-plane TX-H -3.5 -3.6 -4.3 TX-V -18.0 -16.6 -17.4 Plus(H,V) -3.4 -3.4 -4.1 3-plane TX-H -5.3 -5.4 -6.2 TX-V -5.2 -5.2 -5.8 -2.3 -2.3 -3.0 Efficiency [dB] -2.2 -2.3 -3.0 VSWR [:1] 1.3 1.5 2.2 *Note: Peak gain(3-plane)=Peak(XY[H],XY[V],YZ[H])YZ [V],ZX[H])ZX[V]) *Note:The value is average value in 1 round of each inclination direction angle. Frequency [MHz] Radiation pattern *Note: Average gain(3-plane)=Average(XY[Plus(H,V)], YZ[Plus(H,V)],ZX[Plus(H,V)]) XY-plane @2450MHz YZ-plane @2450MHz ZX-plane @2450MHz (-X) (+Z) (+Z) (-Y) (+Y) (-Y) (+Y) (+X) (-X) unit: dBi (+X) unit: dBi (-Z) unit: dBi (-Z) 14.Mar.2014 20140314M****_**** : VSWR [:1] : Efficiency [dB] : -45-35-25-15 -5 5 TX-HTX-V +Y +X +Z +Y +X +Z +Y +X +Z -45-35-25-15 -5 5 TX-HTX-V -45-35-25-15 -5 5 TX-HTX-V 123456789 1011 1950 2450 2950 -10-9-8-7-6-5-4-3-2-10 VSWREfficiency Span:1GHz100MHz /DIV PCB Antenna +Y +Z +X Confidential Antenn Fee PCB Name：PB-140003

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00-1407) FCC ID: RYYWYSAGVDX7 Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. This module has RF shielding with metal case. Refer to external photo. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Using IC, model No. 88W8801, has buffered circuit. 3. The modular transmitter must have its own power supply regulation. Voltage put into this module from host equipment is routed thorough power supply regulation on the equipment and stably used within specification. Instruction to installer of this module is provided in user manual. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. Yes, this module use pattern antenna. Refer to antenna information. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Yes, this testing is performed by stand-alone configuration. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. The label of this module with its own FCC ID is put on PCB. Exterior label instruction to installer of this module is provided in user manual. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. Instruction for operational requirements is provided in user manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. This module complies with RF exposure requirements and instruction for users is provided in the user manual. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): Manabu Satomi Date: 11 th August 2014 Signature:

WYSAGVDX7 External Photo WYSAGVDX7 External PhotoWYSAGVDX7 External Photo WYSAGVDX7 External Photo Confidential Upper Side Lower Side TAIYO YUDEN CO.,LTD.

TAIYO YUDEN CO.,LTD. Control No. Control name APPROVED CHECKED DRAWN DESIGNED Label Design 14/07/14 Label Material：PET / Label color ：White / Printing ：Black 材質 ：PET / ラベル色 ：白 / 印字 ：黒 Indication Label description 1) Model ：WYSAGVDX７ 2) Manufacture ：TAIYO YUDEN CO.,LTD. 3) Japan logo mark ：Specified logo mark 4) Japan ID ：001-A00XXX 5) IC ID ：4389B-WYSAGVDX7 6) FCC ID ：RYYWYSAGVDX7 7) Product Lot number ：Four digits 2) 1) 6) 5) 3) 4) 7)

WYSAGVDX7 Internal Photo WYSAGVDX7 Internal PhotoWYSAGVDX7 Internal Photo WYSAGVDX7 Internal Photo Confidential Upper Side Lower Side TAIYO YUDEN CO.,LTD.

Product Development Department Integrated Module & Device Business Division 8-1 Sakae-Cho, Takasaki-shi, Gunma, 370-8522 JAPAN Tel: +81-27-324-2313 Fax:+81-27-324-2314 DATE: 11 th August 2014 Re : Exposure Declaration Manufacturer: TAIYO YUDEN CO., LTD. Equipment name: WYSAGVDX7, Trade name: TAIYO YUDEN Product Description: Wireless LAN Module FCC ID: RYYWYSAGVDX7 / IC ID: 4389B-WYSAGVDX7 1. SAR test exclusion threshold According to 4.3.1 of KDB4474498, test exclusion thresholds at 100MHz to 6GHz at test separation distance ≤50mm are determined by: - For 1-g SAR: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] *[√f(GHz)] ≤ 3.0 2. Evaluation condition Frequency Minimum separation distance(mm) Maximum conducted average power dBm mW 2400-2483.5 5 7.71 5.902 3. Evaluation result [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] *[√f(GHz)] = 1.86 the calculation value ≤ 3.0. Therefore, our model is applicable to exclusion and not required SAR test. Sincerely, Manabu Satomi, Deputy Manager TAIYO YUDEN CO., LTD. INTEGRATED MODULE & DEVICE BUSINESS DIV.

Report No.: RF140720C01A 1 of 52 Report Format Version 5.2.1 Reference No.: 140720C02 FCC TEST REPORT REPORT NO.: RF140720C01A MODEL NO.: WYSAGVDX7 FCC ID: RYYWYSAGVDX7 RECEIVED: Jul. 20, 2014 TESTED: Jul. 30 ~ Aug. 01, 2014 ISSUED: Aug. 08, 2014 APPLICANT: TAIYO YUDEN CO., LTD ADDRESS: 8-1,Sakae-cho,Takasaki-shi, Gunma, 370-8522, Japan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140720C01A 2 of 52 Report Format Version 5.2.1 Reference No.: 140720C02 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................................ 4 1. CERTIFICATION ............................................................................................................................ 5 2. SUMMARY OF TEST RESULTS ................................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 6 3. GENERAL INFORMATION ............................................................................................................ 7 3.1 GENERAL DESCRIPTION OF EUT .............................................................................................. 7 3.2 DESCRIPTION OF TEST MODES ................................................................................................ 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................................ 9 3.3 DUTY CYCLE OF TEST SIGNAL ................................................................................................ 11 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................ 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................. 13 4. TEST TYPES AND RESULTS ..................................................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ..................................................... 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................... 14 4.1.2 TEST INSTRUMENTS ................................................................................................................. 15 4.1.3 TEST PROCEDURES ................................................................................................................. 16 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................................... 16 4.1.5 TEST SETUP ............................................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS ................................................................................................ 17 4.1.7 TEST RESULTS .......................................................................................................................... 18 4.2 CONDUCTED EMISSION MEASUREMENT .............................................................................. 28 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................... 28 4.2.2 TEST INSTRUMENTS ................................................................................................................. 28 4.2.3 TEST PROCEDURES ................................................................................................................. 29 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................................... 29 4.2.5 TEST SETUP ............................................................................................................................... 29 4.2.6 EUT OPERATING CONDITIONS ................................................................................................ 29 4.2.7 TEST RESULTS .......................................................................................................................... 30 4.3 6dB BANDWIDTH MEASUREMENT .......................................................................................... 32 4.3.1 LIM…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TE 2 3 RADIATED EMISSION TEST 4