SAOZMWE450WiFi Storage Device

1 WWW.ZALMAN.COM ZM-WE450 English / 한글 / Français / Pусский Ver. 140116 www.ZALMAN.com User Manual 2 WWW.ZALMAN.COM FCC Class B Information This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. Important Note : FCC Radiation Exposure Statement For body worn operation, this device has been tested and meets FCC RF Exposure guidelines that position the EUT a minimum of 5 mm from the body. SAR information: 0.406 W/kg (1g) European Unio Regulatory Notice This device bearing the CE marking is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This device complies with the following hamonized European standards. Health : EN62311:2008 Safety : EN60950-1:2006 + A1:2010 + A11:2009 + A12:2011 EMC : EN301 489-1 V1.9.2:2011, EN301 489-17 V2.2.1:2012 Radio : EN300 328 V1.7.1:2006 ● The following CE marking is valid for EU harmonized telecommunications products. 3 WWW.ZALMAN.COM 1. Caution ※ Please read manual befor using the ZM-WE450 ※ Risk of explosion if battery is replaced by incorrect type. Dispose of used batteries according to the instructions. 1) The external HDD manufacturer is not responsible for any data stored in the external HDD nor liable for any emotional or physical damages caused due to data loss. 2) If you disassemble the product or remove/damage the stickers and/or labels attached on the product, you cannot receive the warranty service. 3) Do NOT touch the circuit with bare hands. The chip controlling wifi external hdd case is a electrostatic sensitive part. It may not operate properly if the circuit is damaged by the electrostatic discharge. 4) Visit homepage (www.zalman.com) to download firmware upgrades and user guide. Product design and specifications may be revised to improve quality and performance. Shield Case & bolts 2pcs & Bolt cover 2pcs & EMI Shielding Tape USB 3.0 CableScrew driver & bolts 4pcs & Rubber foot 4pcs User guide Quick Guide 2. Contents 3. Specifications ※ System minimum requirement : Intel Pentium 350MHz or higher PC / Memory 60MB or higher Model Spec. ZM-WE450 HDD Support2.5” HDD/SSD (Hight 9.5mm) InterfaceUSB3.0 / USB2.0, IEEE 802.11 b/g/n Data transfer rateWifi : Up to 150Mbps / USB3.0 : Max 5Gbps / USB2.0 : Max 480Mbps Battery TypeLithium Polymer Battery Battery Size5,200mAh Client OS (Wifi)IOS 5.0, Android 4.0 and above OS Support(USB)Window XP / Vista / 7 / 8(32/64bit), Mac OS X 10x I/OPower Button, USB3.0 Micro B Type LED IndicatorWifi, Internet Bridge, HDD, Battery LED Dimension135 x 88 x 23.7mm PouchZM-WE450 ENGLISH 4 WWW.ZALMAN.COM 3. Name of Parts 4. Assembly Product No.Parts ①USB 2.0 Port : Power bank ② micro-B USB Port : USB 3.0 Cable ③ Power button * Long press more than 2sec : Power On / Off *Short press less than 2sec : Display the battery capacity ④ Reset button hole Long press button(15sec) : Restore Factory Settings ⑤ WiFi indicator ⑥ Bridge mode indicator ⑦External HDD indicator ⑧ Power / Charger indicator 1) Power Level 50 ~ 100% : Green LED 2) Power Level 25 ~ 49% : Yellow LED 3) Power Level 0 ~ 24% : Red LED 4) Unit charging : Flashing Green LED ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ② HDD set into PCBA and close top cover (Apply EMI Shielding tape) ① Remove the top cover and HDD into Shielding and fixed by 2 bolt A and Bolt cover. ③ Bolt B from bottom and add rubber foot Bolt cover Bolt A Bolt B Rubber foot 5 WWW.ZALMAN.COM 5. How to use ① Charging the ZM-WE450 : Use the micro USB cable to connect a charger to the ZM-WE450 micro USB port in order to charge. A full charge takes about 5.5 hours to complete. ② Setting : Go to the Apple App Store / Google Play Site, then download and install the free application Z-Drive Air. ③ Using as an External HDD : Turn off the power, and connect the ZM-WE450 to a computer using the micro USB cable to transfer data. ④ Phone or Tablet USB ⑤ PC or Laptop Wireless hotspot use : Connet to the ZM-WE450 with your computer. Open a web browser and enter the URL: 192.168.99.1 and enter the following settings page. ⑥ Setting Page : Enter your user name and password (default values are "admin"). Click the "Internet Access" option, and select the desired network hotspot. This will share the Internet access with multiple users. ※ Phone or Tablet Wireless hotspot : Connect mobile device to ZM-WE450 and start Z-Drive Air program ※ PC or Notebook Wireless hotspot : Connect the computer to ZM-WE450 and enter 192.168.99.1 in the URL web browser ⑦ Using the ZM-WE450 as Power bank : With the power on/off, use a USB cable to connect the mobile device to be charged to the ZM-WE450 Power bank slot. Open the network settings page of the computer and find the wireless network named Z-Drive Air-XXX. Click to join this network, and then enter the network security key: 12345678 (default password) to connect. Then execute application Z-Driv…

Text truncated - open the document above for the full version.

MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 1 APPROVAL SHEET (RoHS) CUSTOMER : CUSTOMER’S PART NO. : DESCRIPTION : Multi-layer Chip Antenna PART NO. : LTA-6025-2G4S3-B1 DATE : AUTHORIZED BY : Yunwei Lin FULLY APPROVED PARTIALLY APPROVED REJECTED SIGN SUGGESTION 美磊科技股份有限公司 MAG. LAYERS SCIENTIFIC-TECHNICS CO., LTD HEAD OFFICE / HSINCHU PLANT No 18, Tz-Chiang Road, Hsin-Chu Industrial Park, Hsin-Chu, Taiwan TEL: +886-3-5972488 FAX: +886-3-5972477 http://www.maglayers.com.tw E-mail：[email protected] MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 2 ■ ■ ■ A A A P P P P P P L L L I I I C C C A A A T T T I I I O O O N N N WLAN, Home RF, Bluetooth, etc. ■ ■ ■ F F F E E E A A A T T T U U U R R R E E E S S S ■ Compact Size Miniaturized SMD packaged in low profile and lightweight. ■ Wide Bandwidth ■ High Soldering Heat Resistance High quality termination allows both flow and re-flow soldering methods to be applied. ■ Available in Tape and Reel Packaging for Automatic Mounting ■ Very Small Ground Clearance to Save Real Estate ■ ■ ■ P P P R R R O O O D D D U U U C C C T T T I I I D D D E E E N N N T T T I I I F F F I I I C C C A A A T T T I I I O O O N N N LTA – 6025 –###xx – B1 c d e f c Product Code d Dimension Code e Series Type (### represents center frequency and xx represents material type) f Design Code ■ E E E L L L E E E C C C T T T R R R I I I C C C A A A L L L R R R E E E Q Q Q U U U I I I R R R E E E M M M E E E N N N T T T S S S Part NO. Frequency ImpedanceBandwidth*Gain* VSWR Polarization LTA-6025-2G4S3-B1 2450MHz 50 Ohms ~100 MHz 0 dBi 2.5 max. Linear *Depend on PCB layout. MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 3 ■ ■ ■ P P P R R R O O O D D D U U U C C C T T T D D D I I I M M M E E E N N N S S S I I I O O O N N N L W T D 6.00±0.2 2.50±0.2 1.00±0.2 1.00±0.2 b 0.5±0.2 NOTE：Dimensions in mm ■ T T T E E E R R R M M M I I I N N N A A A L L L C C C O O O N N N F F F I I I G G G U U U R R R A A A T T T I I I O O O N N N c e d f c GND d Feed Termination e N.C. f N.C. ■ ■ ■ M M M E E E A A A S S S U U U R R R I I I N N N G G G D D D I I I A A A G G G R R R A A A M M M Test Instrument: Agilent E5071A Network Analyzer L W T D b Network Analyzer (ENA) Port 1 (50 ohm) MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 4 ■ ■ ■ R R R E E E C C C O O O M M M M M M E E E N N N D D D E E E D D D P P P C C C B B B L L L A A A Y Y Y O O O U U U T T T ■ ■ ■ E E E L L L E E E C C C T T T R R R I I I C C C A A A L L L C C C H H H A A A R R R A A A C C C T T T E E E R R R I I I S S S T T T I I I C C C S S S ( ( ( T T T = = = 2 2 2 5 5 5 °C °C °C ) ) ) Unit : mm Ground Land Matching Network 19 43 ANT 50 ohm feed line Tuning trace MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 5 R R R A A A D D D I I I A A A T T T I I I O O O N N N P P P A A A T T T T T T E E E R R R N N N Y-Z Plane Horizontal Y Z Y- Z P l a n e Vertical Y- Z P l a n e Total -Y X Z -Y X Z -Y X Z Peak Gain –10.25dBi Peak Gain –1.04dBi Peak Gain –0.93dBi Y Z Y Z MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 6 X-Z Plane Horizontal X-Z Plane Vertical X-Z Plane Total -Y X Z -Y X Z -Y X Z Peak Gain 0.33dBi Peak Gain –7.77dBi Peak Gain 0.38dBi X Z X Z X Z MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 7 X-Y Plane Horizontal X-Y Plane Vertical X-Y Plane Total -Y X Z -Y X Z -Y X Z Peak Gain –0.67dBi Peak Gain –10.64dBi Peak Gain –0.34dBi Y X Y X Y X MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 8 ■ ■ ■ A A A T T T T T T E E E N N N T T T I I I O O O N N N R R R E E E G G G A A A R R R D D D I I I N N N G G G P P P C C C B B B B B B E E E N N N D D D I I I N N N G G G (a) PCB shall be designed so that products are not subjected to the mechanical stress for board wrapage. Product shall be located in the sideway direction to the mechanical stress. (b) Products (A,B,C,D) shall be located carefully so that products are not subjected to the mechanical stress due to warping the board. Because they may be subjected to the mechanical stress in order of A>C>B≒D. B D C Seam Slit A a b Length: a>b a b (Poor example) Length: a>b a b (Good example) MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 9 ■ ■ ■ R R R E E E L L L I I I A A A B B B I I I L L L T T T Y Y Y T T T E E E S S S T T T Item Condition Specification Thermal shock -40 ~+85 for 100 cycles each cycl°C°Ce being 30 min No apparent damage Fulfill the electrical spec. after test Humidity resistance 85±2 , 80~90% R.H. for 500 hours°C No apparent damage Fulfill the electrical spec. after test High temperature resistance +85±2 for 500 hours°C No apparent damage Fulfill the electrical spec. after test Low temperature resistance -40±3 for 500 hours°C No apparent damage Fulfill the electrical spec. after test Drop shock Dropped onto printed circuit board from 100cm height three times in x, y, z directions. The terminals shall be protected. No apparent damage Soldering heat resistance Preheating temperature : 150±10°C Preheating time : 1 to 2 minutes Solder bath temperature : 260±5°C Bathing time : 5±0.5 seconds No apparent damage Bending test onto printed circuit board Solder specimen LTCC components on the test printed circuit board (L: 100 x W: 40 x T: 1.6mm) in appended recommended PCB pattern. Apply the load in direction of the arrow until bending reaches 2 mm. Unit: mm No apparent damage Solderability The dipped surface of the terminal shall be at least 75% covered with solder after dipped in solder bath of 235±5 for 3±0.5 seconds.°C No apparent damage ■ ■ ■ S S S T T T O O O R R R A A A G G G E E E C C C O O O N N N D D D I I I T T T I I I O O O N N N The temperature should be within 0 ~ 30°C and humidity should be less than 75% RH. The product should be used within 6 months from the time of delivery. MAG.LAYERS LTA-6025-2G4S3-B1_V01 JUL 2006 10 ■ ■ ■ R R R E E E C C C O O O M M M M M M E E E N N N D D D E E E D D D R R R E E E F F F L L L O O O W W W S S S O O O L L L D D D E E E R R R I I I N N N G G G P P P R R R O O O F F F I I I L L L E E E T s min T s max t L t P t S Preheat T P T L Critical Zone T L to T P Ramp-down Ramp-up t=25 °C to…

Text truncated - open the document above for the full version.

FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC APPENDIX 2 PHOTOGRAPHS OF EUT FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC EUT – 1 EUT – 2

FCC ID LABEL FORMAT AND LOCATION Applicant: Zalman Tech Co.,Ltd. FCC ID: SAOZMWE450

FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC APPENDIX 3 PHOTOGRAPHS OF EUT FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC EUT – 1 EUT – 2 FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC EUT – 3 EUT – 4 FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC EUT – 5 EUT – 6 FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC EUT – 7 EUT – 8 ~ End of Report ~ Antenna

Page: 1 of 37 TEST REPORT of FCC SAR New Application; Class I PC; Class II PC Product: WiFi Storage Device Brand: ZALMAN Mode: ZM-WE450 Model Difference: N/A FCC ID: SAOZMWE450 Standard: FCC 47 CFR Part2(2.1093) IEEE C95.1-1999; IEEE 1528 FCC OET 65 Supplement C(Edition 01-10) Applicant: Zalman Tech Co.,Ltd. Address: #1007 Daeryung Techno Town III, 448 Gasan-dong, Gumchun-gu, Seoul, 153-803, Korea Test Performed by: International Standards Laboratory <Lung-Tan LAB> *Site Registration No.: TAF: 0997 *Address: No. 120, Lane 180, San Ho Tsuen, Hsin Ho Rd. Lung-Tan Hsiang, Tao Yuan County 325, Taiwan *Tel : 886-3-407-1718; Fax: 886-3-407-1738 Report No.: ISL-13LR260FSAR Issue Date : 2014/01/06 Test results given in this report apply only to the specific sample(s) tested and are traceable to national or international standard through calibration of the equipment and evaluating measurement uncertainty herein. This report MUST not be used to claim product endorsement by TAF or any agency of the Government. This test report shall not be reproduced except in full, without the written approval of International Standards Laboratory. -2 of 37- FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FSAR VERIFICATION OF COMPLIANCE Applicant: Zalman Tech Co.,Ltd. Product Description: WiFi Storage Device Brand Name: ZALMAN Model No.: ZM-WE450 Model Difference: N/A FCC ID: SAOZMWE450 Date of Receipt: 2014/01/02 Date of Test: 2014/01/02 ~ 2014/01/03 Standard: FCC 47 CFR Part2(2.1093) IEEE C95.1-1999; IEEE 1528 FCC OET 65 Supplement C(Edition 01-10) We hereby certify that: All the tests in this report have been performed and recorded in accordance with the standards described above and performed by an independent electromagnetic compatibility consultant, International Standards Laboratory. The test results contained in this report accurately represent the measurements of the characteristics and the energy generated by sample equipment under test at the time of the test. The sample equipment tested as described in this report is in compliance with the limits of above standards. Test By: Date: 2014/01/06 Dino Chen / Engineer Prepared By: Date: 2014/01/06 Arno Hsieh / Supervisor Approved By: Date: 2014/01/06 Vincent Su / Technical Manager -3 of 37- FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FSAR Version Version No. Date Description 00 2014/01/06 Initial creation of document -4 of 37- FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FSAR Table of Contents 1 STATEMENT OF COMPLIANCE ........................................................................... 5 2 GENERAL INFORMATION ..................................................................................... 6 2.1 DESCRIPTION OF DEVICE UNDER TEST (DUT) .......................................................................... 6 2.2 DUT PHOTOS ............................................................................................................................. 7 2.3 APPLIED STANDARDS ................................................................................................................ 7 2.4 DEVICE CATEGORY AND SAR LIMITS ....................................................................................... 7 2.5 TEST ENVIRONMENT .................................................................................................................. 7 2.6 TEST CONFIGURATION ............................................................................................................... 7 3 SPECIFIC ABSORPTION RATE (SAR) ................................................................. 8 3.1 INTRODUCTION .......................................................................................................................... 8 3.2 SAR DEFINITION ....................................................................................................................... 8 4 SAR MEASUREMENT SYSTEM ............................................................................. 9 4.1 ALSAS-10U SYSTEM DESCRIPTION ......................................................................................... 9 4.2 E-FIELD PROBE ALS-E-020S .................................................................................................. 10 4.3 DAQ-PAQ (ANALOG TO DIGITAL ELECTRONICS) ALS-DAQ-PAQ-3 BOUNDARY DETECTION UNIT ALS-PMDPS-3 ............................................................................................................... 12 4.4 AXIS ARTICULATED ROBOT ALS-F3 ...................................................................................... 14 4.5 ALSAS UNIVERSAL WORKSTATION ALS-UWS ..................................................................... 14 4.6 SAM PHANTOMS ALS-P-SAM-L / ALS-P-SAM-R ................................................................ 15 4.7 UNIVERSAL DEVICE POSITIONER ............................................................................................ 17 4.8 TEST EQUIPMENT LIST ............................................................................................................ 18 5 TISSUE SIMULATING LIQUIDS .......................................................................... 19 6 SAR MEASUREMENT EVALUATION ................................................................ 21 7 DUT TESTING POSITION ..................................................................................... 23 8 SAR MEASUREMENT PROCEDURES ................................................................ 26 9 SAR TEST RESULTS ............................................................................................... 28 9.1 CONDUCTED POWER TABLE: .................................................................................................... 28 9.2 TEST RECORDS FOR BODY SAR TEST ..................................................................................... 30 APPENDIX A TEST SETUP PHOTOS ....................................…

Text truncated - open the document above for the full version.

Page: 1 of 98 TEST REPORT of FCC Part 15 Subpart C New Application; Class I PC; Class II PC Product : WiFi Storage Device Brand: ZALMAN Model: ZM-WE450 Model Difference: N/A FCC ID: SAOZMWE450 FCC Rule Part: §15.247, Cat: DTS Applicant: Zalman Tech Co.,Ltd. Address: #1007 Daeryung Techno Town III, 448 Ga- san-dong, Gumchun-gu, Seoul, 153-803, Korea Test Performed by: International Standards Laboratory <Lung-Tan LAB> *Site Registration No. BSMI: SL2-IN-E-0013; MRA TW1036; TAF: 0997; IC: IC4067B-3; *Address: No. 120, Lane 180, San Ho Tsuen, Hsin Ho Rd. Lung-Tan Hsiang, Tao Yuan County 325, Taiwan *Tel : 886-3-407-1718; Fax: 886-3-407-1738 Report No.: ISL-13LR260FC Issue Date : 2013/12/26 Test results given in this report apply only to the specific sample(s) tested and are traceable to nation- al or international standard through calibration of the equipment and evaluating measurement uncertainty herein. This report MUST not be used to claim product en- dorsement by TAF, NVLAP or any agency of the Government. This test report shall not be reproduced except in full, without the written approval of International Standards Laboratory. -2 of 88- FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC VERIFICATION OF COMPLIANCE Applicant: Zalman Tech Co.,Ltd. Product Description: WiFi Storage Device Brand Name: ZALMAN Model No.: ZM-WE450 Model Difference: N/A FCC ID: SAOZMWE450 Date of test: 2013/12/01 ~ 2013/12/25 Date of EUT Received: 2013/12/01 We hereby certify that: All the tests in this report have been performed and recorded in accordance with the standards de- scribed above and performed by an independent electromagnetic compatibility consultant, Interna- tional Standards Laboratory. The test results contained in this report accurately represent the measurements of the characteristics and the energy generated by sample equipment under test at the time of the test. The sample equip- ment tested as described in this report is in compliance with the limits of above standards. Test By: Date: 2013/12/26 Dion Chang / Engineer Prepared By: Date: 2013/12/26 Gigi Yeh / Specialist Approved By: Date: 2013/12/26 Vincent Su / Technical Manager -3 of 88- FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC Version Version No. Date Description 00 2013/12/26 Initial creation of document -4 of 88- FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC Table of Contents 1 GENERAL INFORMATION .................................................................................................... 6 1.1 Related Submittal(s) / Grant (s) ..................................................................................................... 7 1.2 Test Methodology .......................................................................................................................... 7 1.3 Test Facility .................................................................................................................................... 7 1.4 Special Accessories ........................................................................................................................ 7 1.5 Equipment Modifications ............................................................................................................... 7 2 SYSTEM TEST CONFIGURATION ....................................................................................... 8 2.1 EUT Configuration ........................................................................................................................ 8 2.2 EUT Exercise ................................................................................................................................. 8 2.3 Test Procedure ................................................................................................................................ 8 2.4 Configuration of Tested System ..................................................................................................... 9 3 SUMMARY OF TEST RESULTS .......................................................................................... 10 4 DESCRIPTION OF TEST MODES ....................................................................................... 10 5 CONDUCTED EMISSION TEST........................................................................................... 11 5.1 Standard Applicable: .................................................................................................................... 11 5.2 Measurement Equipment Used: ................................................................................................... 11 5.3 EUT Setup: ................................................................................................................................... 11 5.4 Measurement Procedure: ............................................................................................................. 12 5.5 Measurement Result: ................................................................................................................... 12 6 PEAK /AVERAGE UTPUT POWER MEASUREMENT .................................................... 15 6.1 Standard Applicable: .................................................................................................................... 15 6.2 Measurement Equipment Used: ................................................................................................... 16 6.3 Test Set-up: .................................................................................................................................. 16 6.4 Measurement Procedure: ............................................................................................................. 16 6.5 Measurement Result: ................................................................................................................... 17 7 6dB Bandwidth(EBW) ..............................................................…

Text truncated - open the document above for the full version.

FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC APPENDIX 1 PHOTOGRAPHS OF SET UP FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC Radiated Emission Set up Photo FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC FCC ID: SAOZMWE450 International Standards Laboratory Report Number: ISL-13LR260FC Conducted Emission Set up Photo