SDBSLC200Remote Telemetry Module

Reliability and Compliance T: 919-317-6351 639 Davis Drive F: 919-317-6210 Morrisville, NC 27560 USA www.sensus.com LETTER OF AUTHORIZATION Wednesday, November 28, 2012 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: I hereby appoint Sam Wismer of Advanced Compliance Solutions, Inc. to act as our agent in the preparation of an application for equipment authorization of the SLC200 to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name SLC200 and FCC IDENTIFIER SDBSLC200 listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. This authorization is valid for SLC200 ONLY, and shall not be utilized for any other matters on the behalf of Sensus. Sincerely, Al Servais | Reliability and Compliance Program Manager 639 Davis Drive | Morrisville, NC 27560 USA T: 919-317-6351 | C: 919-208-8983 | [email protected] | www.sensus.com

5015 B. U. Bowman Dr. Buford, GA 30518 December 20, 2012 ACS TCB 5015 B.U. Bowman Drive Buford, GA 30518 Re: FCC ID: SDBSLC200 To Whom It May Concern: The following application is submitted on behalf of our client, Sensus Metering Systems, Inc., for evaluation of their model SLC200 for certification under FCC Part 24 Subpart D and Part 101 Subpart C. The model SLC200, FCC ID: SDBSLC200, is a wireless transceiver module operating from 901MHz - 960 MHz. The model SLC200 is identical to the Sensus model SLC20 (FCC ID: SDBSLC20) from a hardware perspective except that the model SLC200 offers an integral PCB antenna while the model SLC20 has the PCB antenna section snapped off and provides an RF connector for external antennas. Since the SLC200 module is intended to be implemented into specific host devices, it was evaluated for radiated emissions in the orientation of typical installation. The SLC200 was tested in full to the requirements of the aforementioned rules and was found to be in compliance. Sincerely, Sam Wismer Vice President, Technology Advanced Compliance Solutions, Inc.

Reliability and Compliance T: 919-317-6351 639 Davis Drive F: 919-317-6210 Morrisville, NC 27560 USA www.sensus.com MODULAR APPROVAL REQUEST FORM 11/28/2012 Subject: Modular Approval Requirements for FCC certification for Sensus SLC200 Product. Reference: FCC ID: SDBSLC200 Dear Application Examiner, Sensus SLC200 Product is seeking modular approval for FCC ID: SDBSLC200 This document is to attest that the radio bearing the FCC ID: SDBSLC200 meets the requirements for a modular approval as detailed in the FCC public notice DA00-1407. Compliance to each requirement is described below: 1. The modular transmitter has its own RF shielding. 2. The modular transmitter has buffered modulation/data inputs. 3. The modular transmitter has its own power supply regulation. 4. The modular transmitter complies with the antenna requirements of Section 15.203 and 15.204(c). (The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). 5. The modular transmitter has been tested in a stand-alone configuration, 6. The modular transmitter is labeled with its own FCC ID number. 7. The modular transmitter complies with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. 8. The modular transmitter complies with any applicable RF exposure requirements. Sincerely, Al Servais | Reliability and Compliance Program Manager 639 Davis Drive | Morrisville, NC 27560 USA T: 919-317-6351 | C: 919-208-8983 | [email protected] | www.sensus.com

Reliability and Compliance T: 919-317-6351 639 Davis Drive F: 919-317-6210 Morrisville, NC 27560 USA www.sensus.com 1 of 2 Sensus Non Sensus NonSensus Non Sensus Non- -- -Disclosure Disclosure Disclosure Disclosure Memorandum MemorandumMemorandum Memorandum November 28, 2012 Sensus OEMs: This memorandum serves as an additional agreement between Sensus and its OEMs stating that the OEMs will use the Sensus SLC200 module (See Appendix 1) in accordance with the FCC rules on modular approved devices. The Sensus SLC200 Transceiver is professionally installed inside various third party lighting devices. The module label will be located on the secondary side of the PCB and will display both the FCC and IC IDs of the SLC200 module. Confidentiality of the internal photos and the technical manual is being requested because this is a non-consumer device which is not accessible by the general public, professionally installed, and is only serviceable by Sensus, or designated technicians. Please feel free to contact me directly should there be any questions regarding this matter . Respectfully, Al Servais | Reliability and Compliance Program Manager 639 Davis Drive | Morrisville, NC 27560 USA T: 919-317-6351 | C: 919-208-8983 | [email protected] | www.sensus.com 2 of 2 Sensus Non Sensus NonSensus Non Sensus Non- -- -Disclosure Memorandum Disclosure MemorandumDisclosure Memorandum Disclosure Memorandum A AA Appendix 1 ppendix 1ppendix 1 ppendix 1

Reliability and Compliance T: 919-317-6351 639 Davis Drive F: 919-317-6210 Morrisville, NC 27560 USA www.sensus.com Wednesday, November 28, 2012 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: SDBSLC200 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Justification Schematic 12-2118 - Schematics.pdf Proprietary Information and Trade Secret Parts List 12-2118 - BOM_Parts List.pdf Proprietary Information and Trade Secret Theory Of Operation 12-2118 - Theory of Operation.pdf Proprietary Information and Trade Secret Manual 12-2118 - User Manual.pdf Proprietary Information and Trade Secret Internal Photos 12-2118 - Internal Photos.pdf Proprietary Information and Trade Secret Tune-Up Procedure 12-2118 - Tune-Up Procedure.pdf Proprietary Information and Trade Secret Block Diagram 12-2118 - Block Diagram.pdf Proprietary Information and Trade Secret Confidentiality of the Internal Photos is being requested because this is a non-consumer device which is not accessible by the general public and is only serviceable by the applicant or designated technicians. The Manual is technical and is not provided to the consumer because the consumer cannot service or install the device. Therefore confidentiality of the Manual is also requested. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The product covered by this Confidentiality Request may or may not be sold to any OEM and is only installed in Sensus Products by Sensus Employees or Contractors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Al Servais | Reliability and Compliance Program Manager 639 Davis Drive | Morrisville, NC 27560 USA T: 919-317-6351 | C: 919-208-8983 | [email protected] | www.sensus.com

3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Certification Exhibit FCC ID: SDBSLC200 IC: 2220A-SLC200 FCC Rule Part: CFR 47 Part 24 Subpart D, Part 101 Subpart C IC Radio Standards Specification: RSS 119, RSS 134 ACS Project: 12-2118 Manufacturer: Sensus Metering Systems, Inc. Model: SLC200 External Photos Model: SLC200 FCC ID: SDBSLC200 IC: 2220A-SLC200 The SLC200 is a modular device in which internal photos have been held confidential. There are no associated external photographs considering the modular classification. ACS Project: 12-2118 Advanced Compliance Solutions Page 2

3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Certification Exhibit FCC ID: SDBSLC200 IC: 2220A-SLC200 FCC Rule Part: CFR 47 Part 24 Subpart D, Part 101 Subpart C IC Radio Standards Specification: RSS 119, RSS 134 ACS Project: 12-2118 Manufacturer: Sensus Metering Systems, Inc. Model: SLC200 Label Information Model: SLC200 FCC ID: SDBSLC200 IC: 2220A-SLC200 Figure 1: Sample Label and Location ACS Project: 12-2118 Advanced Compliance Solutions Page 2

3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Certification Exhibit FCC ID: SDBSLC200 IC: 2220A-SLC200 FCC Rule Part: CFR 47 Part 24 Subpart D, Part 101 Subpart C IC Radio Standards Specification: RSS 119, RSS 134 ACS Project Number: 12-2118 Manufacturer: Sensus Metering Systems, Inc. Model: SLC200 RF Exposure Model: SLC200 FCC ID: SDBSLC200 IC: 2220A-SLC200 General Information: Applicant: Sensus Metering Systems, Inc. ACS Project: 12-2118 Device Category: Mobile Environment: General Population/Uncontrolled Exposure Technical Information: Antenna Type: PCB Asymmetrical Dipole Antenna Antenna Gain: 2 dBi Maximum Transmitter Conducted Power: 29.21 dBm, 833.68 mW Maximum System EIRP: 31.21 dBm, 1321.3 mW Exposure Conditions: Greater than 20 centimeters MPE Calculation The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG π Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) MPE Calculator for Mobile Equipment Limits for General Population/Uncontrolled Exposure* 90029.210.60833.6821.585 200.263 Power Density (mW/cm^2) Distance (cm) Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/Cm2) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW eq.) Installation Guidelines The installation manual should contain text similar to the following advising how to install the equipment to maintain compliance with the FCC RF exposure requirements: RF Exposure In accordance with FCC requirements of human exposure to radio frequency fields, the radiating element shall be installed such that a minimum separation distance of 20 centimeters will be maintained. Conclusion This device complies with the MPE requirements by providing adequate separation between the device, any radiating structure and the general population. ACS Project: 12-2118 Advanced Compliance Solutions Page 2

3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Certification Test Report FCC ID: SDBSLC200 IC: 2220A-SLC200 FCC Rule Part: CFR 47 Part 24 Subpart D, Part 101 Subpart C IC Radio Standards Specification: RSS 119, RSS 134 ACS Report Number: 12-2118.W06.1A Applicant: Sensus Metering Systems, Inc. Model: SLC200 Test Begin Date: November 3, 2012 Test End Date: November 13, 2012 Report Issue Date: December 11, 2012 For The Scope of Accreditation Under Certificate Number AT-1533 For The Scope of Accreditation Under Lab Code 200612-0 This report must not be used by the client to claim product certification, approval, or endorsement by ACLASS, NVLAP, ANSI, or any agency of the Federal Government. Project Manager: Reviewed by: Thierry Jean-Charles Kirby Munroe EMC Engineer Director, Wireless Certifications Advanced Compliance Solutions, Inc. Advanced Compliance Solutions, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 52 pages ACS Report: 12-2118.W06.1A Advanced Compliance Solutions Page 2 of 52 Table of Content 1.0 GENERAL----------------------------------------------------------------------------------------------------------------------3 1.1 PURPOSE---------------------------------------------------------------------------------------------------------------------3 1.2 PRODUCT DESCRIPTION----------------------------------------------------------------------------------------------------3 1.3 TEST METHODOLOGY-------------------------------------------------------------------------------------------------------3 1.4 EMISSION DESIGNATORS---------------------------------------------------------------------------------------------------5 2.0 TEST FACILITIES-----------------------------------------------------------------------------------------------------------6 2.1 LOCATION---------------------------------------------------------------------------------------------------------------------6 2.2 LABORATORY ACCREDITATIONS/RECOGNITIONS/CERTIFICATIONS-------------------------------------------------6 2.3 RADIATED & CONDUCTED EMISSIONS TEST SITE DESCRIPTION-----------------------------------------------------7 3.0 APPLICABLE STANDARD REFERENCES--------------------------------------------------------------------------9 4.0 LIST OF TEST EQUIPMENT-------------------------------------------------------------------------------------------- 10 5.0 SUPPORT EQUIPMENT------------------------------------------------------------------------------------------------- 11 6.0 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM------------------------------------------------------- 11 7.0 SUMMARY OF TESTS--------------------------------------------------------------------------------------------------- 12 7.1 RF POWER OUTPUT------------------------------------------------------------------------------------------------------ 12 7.2 OCCUPIED BANDWIDTH (EMISSION LIMITS)--------------------------------------------------------------------------- 18 7.3 SPURIOUS EMISSIONS AT ANTENNA TERMINALS--------------------------------------------------------------------- 35 7.4 FIELD STRENGTH OF SPURIOUS EMISSIONS-------------------------------------------------------------------------- 43 7.5 FREQUENCY STABILITY--------------------------------------------------------------------------------------------------- 48 8.0 CONCLUSION-------------------------------------------------------------------------------------------------------------- 52 Model: SLC200 FCC ID: SDBSLC200 IC:2220A-SLC200 ACS Report: 12-2118.W06.1A Advanced Compliance Solutions Page 3 of 52 1.0 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 2 Subpart J, Part 24 Subpart D and Part 101 Subpart C of the FCC’s Code of Federal Regulations, and Industry Canada Radio Standards Specifications RSS-119 and RSS-134 for a modular approval. 1.2 Product Description Sensus Lighting Control model SLC200 powered by the FlexNet™ communications network, allows efficient management of the lighting of large public areas with full control down to an individual lamp. The system utilizes induction and LED lamps that provide brighter, whiter light and excellent color rendering compared to the dim yellow orange glow offered by older lighting technologies. The SLC200 allows smarter use of resources – ranging from shorter operational hours to virtually imperceptible light reduction during non-critical hours for additional cost savings. The Sensus Lighting Control control board includes an integrated metrology chipset to measure energy consumption for each lamp. The system is comprised of power supply, metrology and radio modules. The Power Supply and Metrology modules are combined to form one module where the radio is separate and usually resides in a different compartment within the luminare. The radio operates from a power source provided by the power supply module and is FlexNet based. The SLC200 is identical to the SLC20 except that it is configured with an integral PCB antenna. Manufacturer Information: Sensus Metering Systems, Inc. 639 Davis Drive Morrisville, NC 27560 Test Sample Serial Numbers: 52000718 (RF Conducted), 52000755 (Radiated Emissions) Test Sample Condition: The unit was in good operating conditions with no physical damages. 1.3 Test Methodology 1.3.1 Configurations and Justification The unit was powered using a 3.6 VDC power source. The unit provides different modes of operations corresponding to different modulations and where applicable data is provided for the configuration leading to the highest readings. The radiated emissions evaluations were performed up to the 10 th harmonic. The unit set in the orientation of typical installation during the testing. The RF conducted measurements were performed on t…

Text truncated - open the document above for the full version.

3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Certification Exhibit FCC ID: SDBSLC200 IC: 2220A-SLC200 FCC Rule Part: CFR 47 Part 24 Subpart D, Part 101 Subpart C IC Radio Standards Specification: RSS 119, RSS 134 ACS Project: 12-2118 Manufacturer: Sensus Metering Systems, Inc. Model: SLC200 Test Setup Photos Model: SLC200 FCC ID: SDBSLC200 IC: 2220A-SLC200 ACS Project: 12-2118 Advanced Compliance Solutions Page 2 Figure 1: Radiated Emissions – Front View Model: SLC200 FCC ID: SDBSLC200 IC: 2220A-SLC200 ACS Project: 12-2118 Advanced Compliance Solutions Page 3 Figure 2: Radiated Emissions – Back View Model: SLC200 FCC ID: SDBSLC200 IC: 2220A-SLC200 ACS Project: 12-2118 Advanced Compliance Solutions Page 4 Figure 3: RF Conducted Emissions