SEK41377S1Point of sale payment terminal

Legal Disclaimer The information in this document is subject to change without notice and shall not be construed as a commitment by Banksys S.A./N.V. The content of this document, including but not limited to trademarks, designs, logos, text, images, is the property of Banksys S.A/N.V. and is protected by the Belgian Act of 30.06.1994 related to author’s right and by the other applicable Acts. The Bluetooth trademarks and logos are owned by the Bluetooth SIG, Inc and any use of such marks by Banksys is allowed under license. The contents of this document must not be reproduced in any form whatsoever, by or on behalf of third parties, without the prior written consent of Banksys S.A./N.V. Except with respect to the limited license to download and print certain material from this document for non-commercial and personal use only, nothing contained in this document shall grant any license or right to use any of Banksys S.A./N.V.’s proprietary material. While Banksys S.A./N.V. has made every attempt to ensure that the information contained in this document is correct, Banksys S.A./N.V. does not provide any legal of commercial warranty on the document that is described in this specification. The technology is thus provided “as is” without warranties of any kind, expressed or implied, included those of merchantability and fitness for a particular purpose. Banksys S.A./N.V. does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, product or processes disclosed. To the fullest extend permitted under applicable law, neither Banksys S.A./N.V. nor its affiliates, directors, employees and agents shall be liable to any party for any damages that might result from the use of the technology as described in this document (including without limitation direct, indirect, incidental, special, consequential and punitive damages, lost profits). These terms shall be governed by and construed in accordance with the laws of Belgium. You irrevocably consent to the jurisdiction of the courts located in Brussels for any action arising from or related to the use of this document. Owner’s Manual C-ZAM/SMASH Portable Version 2.2 © Banksys S.A./N.V., December, 2004 C-ZAM/SMASH PORTABLE OWNER’S MANUAL Table of Content FCC Conformity____________________________________________________________________2 ____________________________________________________________3 Declaration of Conformity Introduction_______________________________________________________________________5 The C-ZAM/SMASH Portable terminal_________________________________________________6 _________________________________________________7 Installing the C-ZAM/SMASH Portable Selecting a location_______________________________________________________________7 Unpacking______________________________________________________________________9 ___________________________________10 Getting started with the C-ZAM/SMASH Portable Using the C-ZAM/SMASH Portable___________________________________________________21 _________________________________________________________21 Using the card interfaces ________________________________________________22 C-ZAM/SMASH Portable Maintenance Troubleshooting___________________________________________________________________23 ________________________________________26 General safety information for Banksys Products Compliances____________________________________________________________________26 Safety recommendations_________________________________________________________26 Disposal of the C-ZAM/SMASH Portable___________________________________________27 Technical Specifications____________________________________________________________28 Version: 2.2 1 C-ZAM/SMASH PORTABLE OWNER’S MANUAL FCC Conformity FCC Rules Sections 15.103 and 15.21 ------------------------------------------------- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. The user may find the following booklet prepared by the Federal Communications Commission helpful: “How to identify and Resolve Radio-TV Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington DC 20402, Stock No 004-000-00345-4 15.21 FCC Warning The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Please Note: In order for the installation of this product to maintain compliance with the limits for a Class B device, shielded cables or a ferrite choke on the cable should be used for the Ethernet link. Version: 2.2 2 C-ZAM/SMASH PORTABLE OWNER’S MANUAL Declaration of Conformity Manufacturer: Banksys N.V./S.A. Address: Chaussée de Haecht, 1442 B-1130 Brussels Belgium Tel. +32/(0)2 727 61 11 Fax. +32/(0)2 726 89 26 Product name: C-ZAM/SMASH Dual-Band GSM terminal Interface model number(s): 3031300186 The undersigned hereby declares, on behalf of Banksys that the above-referenced product, to which this declaration relates, is in conformity with the provisions of: Council Directive 89/336/EEC (May 3, 1989) on Electromagnetic Compatibility; Council Directive 73/23/EEC (Feb. 19, 1973) on Low Voltage Equipment Safety; Council Directive 93/68/EEC (July 22, 1993)–Amending Directives 89/336/EEC (EMC) and 73/23/EEC (Low Voltage Equipment Safety). R&TTE Council Directive 91/263/EEC The product is compatible with following norms/standards: EN 301 489-7 - Electromagnetic compatibility and radio spectrum matters. EN 60950 ETS 300 342-1 - TBR19 – TBR20 – TBR31 – TBR32 (C…

Text truncated - open the document above for the full version.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TRP Inc. December 5, 2005 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21045 Gentlemen: Submitted herewith is a request for certification of a GSM pcb BT card FCC ID: SEK41377S1 that will be used in hand held point of transaction banking terminals, Models Smash and Smash D. According to published FCC policy, this type of device is subject to mobile requirements for RF exposure. If you have any questions, please call Phillip Inglis at 410 531 3439 or contact via email at [email protected] . It is also requested that you forward copies of any correspondence and authorization documents to the email address specified above. Sincerely, Phillip Inglis Consultant 14085 Howard Rd Dayton, MD 21936

December 5, 2005 CONFIDENTIALITY REQUEST Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Re:Banksys application for Radio Card for Smash or Smash D terminals FCC ID: SEK41377S1 Gentlemen: Banksys requests, pursuant to 47CFR 0.459, post grant confidentiality for portions of the material contained in this application such that the identified material will be withheld from public inspection following the grant of this authorization. This material, as indicated by request for confidentiality of the item during the electronic submission process and further identified below, includes: 1. Schematic or circuit diagrams. 2. Block diagram 3. Operational description 4. Parts List Specifically, these exhibits contains information relating to circuit function and complexity that could be of benefit to competitors. The material contains trade secrets and confidential information that Banksys does not customarily release to the public and which is otherwise not generally available to the public. Please contact the undersigned by phone at 410-531-3439, by fax at 410-531-0807, by email at [email protected], or by correspondence at the address below if there are any further questions or additional information needed concerning this filing. Regards, (signed) Phillip Inglis, TRP/Cetecom bvba 14085 Howard Rd. Dayton, MD. 21036

ANNEX 4: PHOTOS OF THE EQUIPMENT UNDER TEST GENERAL VIEW RA-05-24076-1

IC ID label and location The following label will be placed on the bottom of the unit and is visible at all times.

Printed circuit board: face 1 RA-05-24076-1 Printed circuit board: face 2 RA-05-24076-1

November 31, 2005 RF Exposure This transmitter has a nominal power output of 0.115 watts. In this application the card is inserted in a hand held banking terminal. Since the unit is only used while at arms length with a communications interval that is very short (sufficient to transfer credit card info only) the Commission considers the application to be mobile device. Information is provided to the user that he should operate the unit only at arm’s length. Compliance with the RF exposure limit for a distance of 20 cm (mobile device classification) for a power output of 115 mW EIRP can be calculated according to Pd = P/4piR 2 or 115/4x3.14x400 = 0.03 mW/cm 2 . This is below the FCC compliance limit. Phillip Inglis Consultant to Banksys

RA-05-24076-1/A Ed. 0 FCC CERTIFICATION Radio Measurement Technical Report standard to apply: RSS–210 Equipment under test: PAYMENT TERMINAL C-ZAM / SMASH I C : 2662A-41377S1 Company: TELESINCRO / INGENICO TRANSMIT TO: Mr CAZOU Company: TELESINCRO / INGENICO Number of pages: 31 including 5 annexes Verification Ed. Date ModifiedEditing Approval pages Name Visa Name Visa 0 30-May-05 Creation L. BERTHAUD Duplication of this test report is only permitted for an integral photographic facsimile. It includes the number of pages referenced here above. This document is the result of testing a specimen or a sample of the product submitted. It does not imply an assessment of the conformity of the whole manufactured products of the tested sample. RA-05-24076-1/A Ed. 0 PAGE: 2 608593.DOC PRODUCT : PAYMENT TERMINAL Reference / model : C-ZAM / SMASH Serial number : ADD1164 MANUFACTURER: BANKSYS (Belgium) COMPANY SUBMITTING THE PRODUCT: Company: TELESINCRO / INGENICO Address: 10, rue du Golf Bâtiment M2 – Parc Innolin 33700 MERIGNAC FRANCE Responsible: Mr CAZOU DATE(S) OF TEST: 13 May 2005 TESTING LOCATION: EMITECH ATLANTIQUE laboratory at ANGERS (49) FRANCE EMITECH laboratory at MONTIGNY LE BRETONNEUX (78) FRANCE Registration Number by FCC: 101696/FRN: 0006 6490 08 Registration Number by Industry Canada: IC4379 TESTED BY: L. BERTHAUD RA-05-24076-1/A Ed. 0 PAGE: 3 608593.DOC CONTENTS TITLE PAGE 1. INTRODUCTION.......................................................................................................................... 4 2. PRODUCT DESCRIPTION .........................................................................................................4 3. NORMATIVE REFERENCE....................................................................................................... 5 4. TEST METHODOLOGY .............................................................................................................5 5. TESTS AND CONCLUSIONS ..................................................................................................... 6 6. OUTPUT POWER TRANSMITTER .......................................................................................... 8 7. SPECTRAL DENSITY TRANSMITTER................................................................................. 10 8. RADIATED EMISSION TRANSMITTER............................................................................... 11 9. RADIATED EMISSION RECEIVER ....................................................................................... 13 ANNEX 1: CHANNEL SEPARATION ......................................................................................... 15 ANNEX 2: CHANNEL BANDWIDTH.......................................................................................... 18 ANNEX 3: TIMING HOPPING AND TIMING CHANNEL...................................................... 21 ANNEX 4: PHOTOS OF THE EQUIPMENT UNDER TEST ................................................... 27 ANNEX 5: PHOTOS OPEN AREA TEST SITE AND TEST SET UP ..................................... 30 RA-05-24076-1/A Ed. 0 PAGE: 4 608593.DOC 1.INTRODUCTION This document presents the result of RADIO test carried out on the following equipment: PAYMENT TERMINAL C-ZAM - SMASH in accordance with normative reference. 2.PRODUCT DESCRIPTION ITU Emission code: 1M00F7D Category: I Utilization: banking payment terminal Antenna type: incorporated antenna Antenna gain: unknown Operating frequency range: I.S.M. band from 2400 MHz to 2483.5 MHz No of channels: 79 Channel spacing: 1 MHz Frequency generation: | SAW Resonator | Crystal ~ Synthesizer Modulation: Frequency Hopping Spread Spectrum | Amplitude | Digital ~ Frequency | Phase Power source: Ni – Mh batteries (5 × 1.2 V) Power level, frequency range and channels characteristics are not user adjustable. The details pictures of the product and the circuit boards are joined with this file. RA-05-24076-1/A Ed. 0 PAGE: 5 608593.DOC 3.NORMATIVE REFERENCE FCC Part 15 (2004) Code of Federal Regulations Title 47 - Telecommunication Chapter 1 - Federal Communications Commission Part 15 - Radio frequency devices Subpart C - Intentional Radiators RSS 210 Issue 5 (2001) Low Power Licence - Exempt Radiocommunication Devices (All Frequency Bands) RSS 210 Issue 5 (2002) Amendment Section 6.2.2 (o) 4.TEST METHODOLOGY Radio performance tests procedures given in RSS 210: Paragraph 6.2.: Non-Momentarily Operated Devices Paragraph 6.2.2 (o): 902-928 MHz; 2400-2483.5 MHz; 5725-5850 MHz ANSI C63.4 (01) Methods of measurement of Radio-Noise Emissions from low-voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. RA-05-24076-1/A Ed. 0 PAGE: 6 608593.DOC 5.TESTS AND CONCLUSIONS Test Description of test Criteria respected ? Comment Procedure RSS 210 Yes No NAp NAs § 6.2.2 (o) a) a 1) Separated channel X Note 6 a 2) 902 - 928 MHz band X a 3) Average time of occupancy on any frequency, and output power X Note 4 b) DSSS X c) Hybrid System X d) d 1) Spectral density X Note 1 d 2) X d 3) X Note 1 e) e 1) Spurious transmitter X e 2) X e 3) Sections 2 to 5 § 5.9 Emission bandwidth X Note 3 Sections 6.3 to 6.6 § 6.3 Restricted band X § 6.4 Frequency stability X § 6.5 Pulsed Operation X § 6.6 Transmitter AC Wire line X Sections 7 to 7.5 § 7.1 Receiver Categories X category II § 7.2 Receiver Spurious Conducted X § 7.3 Receiver Spurious Radiated X § 7.4 Receiver AC Wire line X § 7.5 Scanner Receiver X Section 9 § 9 AC Wire line Conducted Measurement X Section 10 § 10 Antenna Conducted X Section 11 § 11 RF field Measurement Method RF field conversion Section 13 § 13 Near field Measurement X Note 5 Section 14 § 14 Exposure of human RF field X Note 2 NAp: Not Applicable NAs: Not Asked Note 1 : RSS-210 certification the spectral density is less than 50 mW/MHz, indoor use only, not weatherproof equipment, (for information only, the amendment of November 30, 2002 applies), the system does not employ digital modulation. Note 2 : see certificate of conformity …

Text truncated - open the document above for the full version.

A5-OPEN AREA TEST SITE PAGE: 1 608594.DOC OPEN AREA TEST SITE A5-OPEN AREA TEST SITE PAGE: 2 608594.DOC TEST SITE SET UP