SJ21200UAutomotive Controller with Bluetooth

4 Monitor, climate, audio, phone and voice- activated control systems Safety note....................................................... 4-2 Control panel button functions......................... 4-2 How to use multi function button................ 4-4 Start-up screen (model with Navigation system)....................................................... 4-5 Vehicle information and setting........................ 4-5 How to use “STATUS” button ...................... 4-5 How to use “INFO” button .......................... 4-5 Warning display.......................................... 4-9 How to use “SETTING” button................... 4-10 “AUDIO” settings...................................... 4-12 Rear view monitor .......................................... 4-17 How to read the displayed lines................ 4-18 Adjusting the screen................................. 4-18 Operating tips........................................... 4-18 Ventilators...................................................... 4-19 Automatic climate control............................... 4-21 Automatic operation.................................. 4-22 Manual operation...................................... 4-23 Ambient temperature ................................ 4-24 Rear control button (if so equipped) ......... 4-25 Operating tips........................................... 4-25 In-cabin microfilter ................................... 4-25 Servicing climate control........................... 4-25 Audio system ................................................. 4-26 Audio operation precautions ..................... 4-26 Radio ........................................................ 4-26 FM-AM-SATELLITE radio with compact disc (CD) changer............................................. 4-34 CD care and cleaning................................ 4-38 Steering wheel switch for audio control.... 4-38 Audio rear control switch (if so equipped) ................................................. 4-39 INFINITI mobile entertainment system (MES) (if so equipped) .............................. 4-40 Antenna .................................................... 4-49 Car phone or CB radio.................................... 4-49 Hands-free phone system............................... 4-50 Pairing procedure...................................... 4-52 Phonebook registration............................. 4-53 Making a call ............................................ 4-54 Receiving a call......................................... 4-55 During a call ............................................. 4-56 Phone setting............................................ 4-56 Voice-Activated Control System (VACS)........... 4-57 Using the system...................................... 4-57 System features........................................ 4-58 List of voice commands............................. 4-59
04.10.8/Y50-D Troubleshooting guide .............................. 4-63
04.10.8/Y50-D WARNING
Positioning of the heating or air condi- tioning controls and display controls should not be done while driving, in or- der that full attention may be given to driving operation.
Do not disassemble or modify this sys- tem. If you do, it may result in acci- dents, fire, or electric shock.
Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.
In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell coming from it, stop using the system immediately and contact your nearest INFINITI dealer. Ignoring such conditions may lead to accidents, fire, or electric shock. 1. “STATUS” status display button (P.x-x) 2, 6, 7, 8, 9. For navigation system con- trol buttons (Refer to the separate Navigation Own- er’s Manual.) 3. Multi function switch (P.x-x) 4. “PHONE” hands-free phone system button (P.x-x) 5. “ ” brightness control and display ON/OFF button (P.x-x) 10. “INFO” vehicle information button (P.x-x) SAA1095 With Navigation system SAFETY NOTECONTROL PANEL BUTTON FUNCTIONS 4-2Monitor, climate, audio, phone and voice-activated control systems
04.10.8/Y50-D 3 4 5 6 8 7 10 9 11 12 13 Icon will be added. 11. “SETTING” button (P.x-x) 12. “RADIO” AM/FM/CAT band selector button (P.x-x) 13. “DISC” CD/DVD (if so equipped) se- lector button (P.x-x) 1. “STATUS” status display button (P.x-x) 2. “RADIO” AM/FM/CAT band selector button (P.x-x) 3. Multi function switch (P.x-x) 4. “PHONE” hands-free phone system button (P.x-x) 5. “ ” brightness control and display ON/OFF button (P.x-x) 6. “TRIP” drive computer button (P.x-x) 7. “FUEL ECON” button (P.x-x) 8. “DISC” CD/DVD (if so equipped) selec- tor button (P.x-x) SAA1096 Without Navigation system Monitor, climate, audio, phone and voice-activated control systems4-3
04.10.8/Y50-D 4 3 5 6 7 89 10 11 Icon will be added. SR SR 9. “AUDIO TEXT” display button (P.x-x) 10. “INFO” vehicle information button (P.x-x) 11. “SETTING” button (P.x-x) When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. HOW TO USE MULTI FUNCTION BUTTON Choose an item on the display using the eight-directional switch  2 (or four- directional switch  6 without Navigation system) or center dial  3 and push the “ENTER” button  1 for operation. If you push the “BACK” button  4 before the setup is completed, the setup will be canceled and/or the display will return to the previous screen. After the setup is completed, push the “BACK” button  4 and return to the previ- ous screen. For the “VOICE” button  5 functions, refer to the separate Navigation Owner’s Manual. SAA1097 With Navigation system SAA1098 Without Navigation system 4-4Monitor, climate, audio, phone and voice-activated control systems
04.10.8/Y50-D SWITCH START-UP SCREEN (model with…

Text truncated - open the document above for the full version.

Correspondence application for CCA1200U/GCU1200U RE: Xanavi Informatics Corporation FCC ID: SJ21200U Please find answers to comments below 1) Please provide a photograph of the bottom of the Bluetooth module with the label removed. Information have been uploaded 2) The font used on the FCC label makes the ID Numbers and statements unreadable. Please use a different font and provide an updated label. FCC label have been modified and uploaded. 3) Please justify the use of the DoC labeling information (FCC Logo). This labeling is reserved for particular approvals that do not appear to apply to this application (PC Peripheral, Stand alone RX, etc.) FCC has been removed from the label in order to comply with FCC rules. 4) It can not easily be determined if the schematics include the Bluetooth module. If so, please explain where the schematic for the module itself is shown. Note that a schematic for the TX portion of the device is required as specified 2.1033(b)(5) for the RF section. However, if the TX portion of this device is an OEM part, as an alternative, you may provide a parts list that lists that shows that this part is provided by another manufacturer. Please provide either a schematic for the TX or parts list as specified. If a parts list is provided, please clarify if this should be covered by confidentiality. The radio is OEM product. Due to the limitation of information provided by the manufacturer, the schematic couldn’t be submitted with this application. Therefore the part list and modified letter of confidentiality have been uploaded. 5) Please explain the difference between the configurations shown in test photos 1 versus test photos 2. Please justify how photos in 1 are relevant give there is not any case present. Picture 1 should be removed of this application. 6) The users annual should include the following or similar (as appropriate for this device) statements: Comment have been added into exhibit concerning the “FCC warning statement” 7) Please note that the FCC no longer desires that the safe distance for mobile devices be calculated in the RF exposure exhibit if the safe distance is < 20 cm, but instead prefers the power density results to be calculated at 20 cm and compared to the power density limit. The RF exposure has been modified and uploaded. 8) The 731 form shows 75 mW, while the test report shows 0.75 mW. Which is correct? 731 has been modified and uploaded , the correct value is 0.75 mW. 9) The RF exposure exhibit shows 0.8 dBi gain, while the test report states 9.53 dBi. What is the correct gain. Please correct the test report and/or RF exposure exhibit as necessary. 9.53dBi refer to the receiving antenna for the EIRP. The comments have been modified on the test report and uploaded. 10) Please explain the data on page 51 & 54. All data points appear to be 0. Noise was found 20 dB below the limit during the testing, comments have been added into the test report, refer to test report. 11) FYI.....Peak power density requires a sweep time > (Span/3 kHz). This was not appropriately tested. However, given that the output power itself is < than the 8 dBm limit, retesting is not necessary. 12) FYI.....For average emissions on Bluetooth devices, please note that you can take the peak reading and correct by the worse case duty factor per TX frequency. This should be a greater than 20 dB correction factor.

Xanavi Informatics Corporation 1 CCA-1200U Picture Top View Bottom View Front View Rear Surface View Right Side View Left Side View Xanavi Informatics Corporation 1 GCU-1200U Picture Top View Bottom View Front View Rear Surface View Right Side View Left Side View

FCC label

Xanavi Informatics Corporation 1 CCA-1200UPicture Xanavi Informatics Corporation 1 GCU-1200UPicture Xanavi Informatics Corporation 2 InternalView EscutcheonUnit ainBoard MainBoardUnit VD Unit Xanavi Informatics Corporation 3 MainBoardUnit CPUMODULE MainBoard Xanavi Informatics Corporation 4 MainBoard [Top View] CPUMODULE Xanavi Informatics Corporation 5 MainBoard [Bottom View] Xanavi Informatics Corporation 6 CPUModule [Top View] Xanavi Informatics Corporation 7 CPUModule [Bottom View] Xanavi Informatics Corporation 8 EscutcheonUnit BluetoothModuleSet Xanavi Informatics Corporation 9 BluetoothModuleSet BluetoothModule Xanavi Informatics Corporation 10 BluetoothModule [Top View] BluetoothAntenna Xanavi Informatics Corporation 11 BluetoothModule [Bottom View] Xanavi Informatics Corporation 2 InternalView DVDUnitMainBoardUnit VD Unit EscutcheonUnit ainBoard Xanavi Informatics Corporation 3 MainBoardUnit CPUMODULEGPSTuner MainBoard Xanavi Informatics Corporation 4 MainBoard [Top View] CPUMODULE GPSTuner Xanavi Informatics Corporation 5 MainBoard [Bottom View] Xanavi Informatics Corporation 6 CPUModule [Top View] Xanavi Informatics Corporation 7 CPUModule [Bottom View] Xanavi Informatics Corporation 8 EscutcheonUnit BluetoothModuleSet Xanavi Informatics Corporation 9 BluetoothModuleSet BluetoothModule Xanavi Informatics Corporation 10 BluetoothModule [Top View] BluetoothAntenna Xanavi Informatics Corporation 11 BluetoothModule [Bottom View]

BLUETOOTH APPROVALS The following exhibit indicates the FCC Spread Spectrum requirements in Section 15.247 for devices meeting the Bluetooth Specifications in the 2.4 GHz band as of February 2001 operating in the USA. The purpose of this exhibit is to help expedite the approval process for Bluetooth devices. This exhibit provides items that vary for each device and also provides a list of items that are common to Bluetooth devices that explains the remaining requirements. The list of common items can be submitted for each application for equipment authorization. This exhibit only specifies requirements in Section 15.247, requirements in other rule Sections for intentional radiators such as in Section 15.203 or 15.207 must be also be addressed. For each individual device, the following items, 1-7 will vary from one device to another and must be submitted. 1) The occupied bandwidth in Section 15.247(a)(1)(ii). 2) Conducted output power specified in Section 15.247(b)(1). 3) EIRP limit in Section 15.247(b)(3). 4) RF safety requirement in Section 15.247(b)(4) 5) Spurious emission limits in Section 15.247©. 6) Processing gain and requirements for Hybrids in Section 15.247(f) in the acquisition mode. 7) Power spectral density requirement in Section 15.247(f) in the acquisition mode. For all devices, the following items, 1-12, are common to all Bluetooth devices and will not vary from one device to another. This list can be copied into the filing. 1 Output power and channel separation of a Bluetooth device in the different operating modes: The different operating modes (data-mode, acquisition-mode) of a Bluetooth device don’t influence the output power and the channel spacing. There is only one transmitter which is driven by identical input parameters concerning these two parameters. Only a different hopping sequence will be used. For this reason, the RF parameters in one op-mode is sufficient. 2 Frequency range of a Bluetooth device: The maximum frequency of the device is: 2402 – 2480 MHz. This is according the Bluetooth Core Specification V 1.0B (+ critical errata) for devices which will be operated in the USA. Other frequency ranges ( e.g. for Spain, France, Japan) which are allowed according the Core Specification must not be supported by the device. 3 Co-ordination of the hopping sequence in data mode to avoid simultaneous occupancy by multiple transmitters: Bluetooth units which want to communicate with other units must be organized in a structure called piconet. This piconet consist of max. 8 Bluetooth units. One unit is the master the other seven are the slaves. The master co-ordinates frequency occupation in this piconet for all units. As the master hop sequence is derived from it’s BD address which is unique for every Bluetooth device, additional masters intending to establish new piconets will always use different hop sequences. 4 Example of a hopping sequence in data mode: Example of a 79 hopping sequence in data mode: 40, 21, 44, 23, 42, 53, 46, 55, 48, 33, 52, 35, 50, 65, 54, 67, 56, 37, 60, 39, 58, 69, 62, 71, 64, 25, 68, 27, 66, 57, 70, 59, 72, 29, 76, 31, 74, 61, 78, 63, 01, 41, 05, 43, 03, 73, 07, 75, 09, 45, 13, 47, 11, 77, 15, 00, 64, 49, 66, 53, 68, 02, 70, 06, 01, 51, 03, 55, 05, 04 5 Equally average use of frequencies in data mode and short transmissions: The generation of the hopping sequence in connection mode depends essentially on two input values: 1. LAP/UAP of the master of the connection 2. Internal master clock The LAP (lower address part) are the 24 LSB’s of the 48 BD_ADDRESS. The BD_ADDRESS is an unambiguous number of every Bluetooth unit. The UAP (upper address part) are the 24 MSB’s of the 48 BD_ADDRESS. The internal clock of a Bluetooth unit is derived from a free running clock which is never adjusted and is never turned off. For synchronization with other units, only the offsets are used. It has no relation to the time of the day. Its resolution is at least half the RX/TX slot length of 312.5 μs. The clock has a cycle of about one day (23h30). In most case it is implemented as 28 bit counter. For the deriving of the hopping sequence the entire LAP (24 bits), 4 LSB’s (4 bits) (Input 1) and the 27 MSB’s of the clock (Input 2) are used. With this input values different mathematical procedures (permutations, additions, XOR-operations) are performed to generate the sequence. This will be done at the beginning of every new transmission. Regarding short transmissions, the Bluetooth system has the following behavior: The first connection between the two devices is established, a hopping sequence is generated. For transmitting the wanted data, the complete hopping sequence is not used and the connection ends. The second connection will be established. A new hopping sequence is generated. Due to the fact that the Bluetooth clock has a different value, because the period between the two transmission is longer (and it cannot be shorter) than the minimum resolution of the clock (312.5 μs). The hopping sequence will always differ from the first one. 6 Receiver input bandwidth, synchronization and repeated single or multiple packets: The input bandwidth of the receiver is 1 MHz. In every connection, one Bluetooth device is the master and the other one is the slave. The master determines the hopping sequence (see chapter 5). The slave follows this sequence. Both devices shift between RX and TX time slot according to the clock of the master. Additionally the type of connection (e.g. single or multi-slot packet) is set up at the beginning of the connection. The master adapts its hopping frequency and its TX/RX timing is according to the packet type of the connection. Also, the slave of the connection uses these settings. Repeating of a packet has no influence on the hopping sequence. The hopping sequence generated by the master of the connection will be followed in any case. That means, a repeated packet will not be send on the same frequency, it is send on the next frequency …

Text truncated - open the document above for the full version.

JAPAN QUALITY ASSURANCE ORGANIZATION 21-25, KINUTA 1-CHOME, SETAGAYA-KU, TOKYO 157-8573 JAPAN PHONE +81-3-3416-0111, FAX +81-3-3416-9691 Issue Date : November 16, 2004 Page 1 of 1 RF Exposure Calculation Exposure of Humans to RF Fields Requirements Applicant : Xanavi Informatics Corporation Type of Equipment : Bluetooth Module Model No. : LBMB4U8AE3 FCC ID : SJ21200U IC : 5427A-1200U Regulations Applied : CFR 47 FCC 15.247(b)(5) References Documents : CFR 47 FCC 1.1307(b), 1.1310, 2.1093 and OET65 Supplement C RF Exposure Calculations : The following power density, calculated at 20cm from the radiated element, is in accordance with FCC OET65 Appendix B Table(B) “Limit for General Population / Uncontrolled Exposure”. The maximum permissible exposure level is defined with 1mW/cm 2 . The power density can be calculated as below: Where: R = 20 cm P = 0.74 mW(-1.30dBm)(Max. conducted output power at antenna terminal) G = 1.20(numeric gain) = 0.8 dBi(Max. antenna Gain) S = calculated exposure level at 20 cm Then maximum power density generated at 20 cm is 0.0002 mW/cm 2 Summary: The EUT complies with the RF exposure requirement of the above regulation. Masaaki Takahashi Senior Manager JQA EMC Engineering Dept. 2 4/*RGPSπ= SGPRπ4/*=Q

JAPAN QUALITY ASSURANCE ORGANIZATION 21-25, KINUTA 1-CHOME, SETAGAYA-KU, TOKYO 157-8573 JAPAN PHONE +81-3-3416-0111, FAX +81-3-3416-9691 JQA APPLICATION NO.: 400-40471 Issue Date : November 16, 2004 Page 1 of 59 EMI TEST REPORT JQA APPLICATION NO. : 400-40471 Model No. : CCA-1200U / GCA-1200U Type of Equipment : Bluetooth module Regulations Applied : CFR 47 FCC Rules and Regulations Part 15 : Industry Canada RSS-210 Issue 5(inc. Amendment) FCC ID : SJ21200U IC : 5427A-1200U Applicant : Xanavi Informatics Corporation Address : 6-35 Hironodai 2-chome, Zama-shi, Kanagawa 228-0012 Japan Manufacturer : Xanavi Informatics Corporation Address : 6-35 Hironodai 2-chome, Zama-shi, Kanagawa 228-0012 Japan Received date of EUT : August 30, 2004 Final Judgment : Passed Test results in this report are obtained in use of equipment that is traceable to National Institute of Advanced Industrial Science and Technology (AIST) of Japan and National Institute of Information and Communications Technology (NICT) of Japan. The test results only respond to the tested sample. This report should not be reproduced except in full, without the written approval of JQA EMC Engineering Dept. Testing Div. JQA Application No. :400-40471 FCC ID: SJ21200U IC: 5427A-1200U Model No. :CCA-1200U / GCA-1200U Issue Date :November 16, 2004 Standard :CFR 47 FCC Rules Part 15 Page 2 of 59 JAPAN QUALITY ASSURANCE ORGANIZATION TABLE OF CONTENTS Page 1 Documentation 1.1 Test Regulation 4 1.2 General Information 4 1.3 Test Condition 5 – 11 1.4 EUT Modifications / Deviation from Standard 12 1.5 Test results 13 - 14 1.6 Summary 15 1.7 Test Configuration / Operation of EUT 16 1.8 EUT Arrangement (Drawing) 17 - 18 1.9 Preliminary Test and Test-setup (Drawings) 19 – 27 1.10 EUT Arrangement (Photographs) 28 - 29 JQA Application No. :400-40471 FCC ID: SJ21200U IC: 5427A-1200U Model No. :CCA-1200U / GCA-1200U Issue Date :November 16, 2004 Standard :CFR 47 FCC Rules Part 15 Page 3 of 59 JAPAN QUALITY ASSURANCE ORGANIZATION 2 Test Data 2.1 Channel Separation 30 2.2 Minimum Hopping Channel 31 – 32 2.3 Occupied Bandwidth 33 – 35 2.4 Average Time of Occupancy 36 – 38 2.5 Peak Output Power (Conduction) 39 2.6 Peak Output Power (Radiation) 40 2.7 Peak Power Density (Conduction) 41 - 43 2.8 Peak Power Density (Radiation) N/A 2.9 Spurious Emissions (Conduction) 44 - 46 2.10 Spurious Emissions (Radiation) 47 - 52 2.11 AC Power Line Conducted Emissions N/A 2.12 RF Exposure Compliance 53 2.13 Spurious Emissions for Receiver (Radiation) 54 – 55 2.14 AC Power Line Conducted Emissions for Receiver N/A 3 Appendix Test instruments List 56 - 59 JQA Application No. :400-40471 FCC ID: SJ21200U IC: 5427A-1200U Model No. :CCA-1200U / GCA-1200U Issue Date :November 16, 2004 Standard :CFR 47 FCC Rules Part 15 Page 4 of 59 JAPAN QUALITY ASSURANCE ORGANIZATION 1 DOCUMENTATION 1.1 TEST REGULATION FCC Rules and Regulations Part 15 Subpart B and C Radiated Spurious Emissions and Industry Canada IC RSS-210 (inc. amendment) Test procedure : The tests were performed with reference to the FCC Public Notice DA 00-705, released March 30, 2000. The test set-up was made in accordance to the general provisions of ANSIC63.4-2003. 1.2 GENERAL INFORMATION 1.2.1 Test facility : 1) Test Facility located at EMC Engineering Dept. Testing Div. : - No.2 and 3 Anechoic Chambers(3 meters Site). - Shielded Enclosure. Expiration date of FCC test facility filing : May 27, 2005 Open Area Test Site Industry Canada No.: IC4126-4 2) EMC Engineering Dept. Testing Div. is recognized under the National Voluntary Laboratory accreditation Program for satisfactory compliance established in title 15, Part 285 Code of Federal Regulations. NVLAP Lab Code : 200189-0 (Effective through : June 30, 2005) 1.2.2 Description of the Equipment Under Test (EUT) : 1) Type of Equipment : Bluetooth module 2) Product Type : Production 3) Category : Spread Spectrum Transmitter(FHSS) 4) EUT Authorization : Certification 5) FCC ID : SJ21200U IC : 5427A-1200U 6) Trade Name : Xanavi Informatics Corporation 7) Model No. : CCA-1200U / GCA-1200U 8) Operating Frequency Range : 2402 MHz - 2480 MHz 9) Highest Frequency Used in the EUT : 2480 MHz 10) RF Output Power : 0.74 mW (measured value) 11) Serial No. : None 12) Date of Manufacture : - 13) Power Rating : DC 3.3V via main unit 14) EUT Grounding : None 1.2.3 Definitions for symbols used in this test report : x - indicates that the listed condition, standard or equipment is applicable for this report. - indicates that the listed condition, standard or equipment is not applicable for this report. JQA Application No. :400-40471 FCC ID: SJ21200U IC: 5427A-1200U Model No. :CCA-1200U / GCA-1200U Issue Date :November 16, 2004 Standard :CFR 47 FCC Rules Part 15 Page 5 of 59 JAPAN QUALITY ASSURANCE ORGANIZATION 1.3 TEST CONDITION 1.3.1 The measurement of Channel Separation x - was performed. - was not applicable. Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver TR07 Spectrum Analyzer N/A Cable CA11 Attenuator AU18 Antenna N/A 1.3.2 The measurement of Minimum Hopping Channel x - was performed. - was not applicable. Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver TR07 Spectrum Analyzer N/A Cable CA11 Attenuator AU18 Antenna N/A 1.3.3 The measurement of Occupied Bandwidth x - was performed. - was not applicable. Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver TR07 Spectrum Analyzer N/A Cable CA11 Attenuator AU18 Antenna N/A JQA Application No. :400-40471 FCC ID: SJ21200U IC: 5427A-1200U Model No. :CCA-1200U / GCA-1200U Issue Date :November 16, 2004 Standard :CFR 47 FCC Rules Part 15 Page 6 of 59 JAPAN QUALITY ASSURANCE ORGANIZATION 1.3.4 The measurement of Average Time of Occupancy x - was performed. - was not applicable. Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver TR07 Spectrum Analyzer N/A Cable CA11 Attenuator AU18 Anten…

Text truncated - open the document above for the full version.

JQA Application No. :400-40471 FCC ID: SJ21200U IC: 5427A-1200U Model No. :CCA-1200U / GCA-1200U Issue Date :November 16, 2004 Standard :CFR 47 FCC Rules Part 15 Page 29 of 59 JAPAN QUALITY ASSURANCE ORGANIZATION PHOTOGRAPHS OF EUT CONFIGURATION FOR RADIATED EMISSIONS MEASUREMENT Photograph present configuration with maximum emission(CCA-1200U configuration)