SJLPB7315PANIC BUTTON

1 PB - 7 The Panic Button is used to activate the panic alarm. PANIC BUTTON Pressing this button once will trigger the panic alarm regardless of whether the system is Armed or Disarmed. TX INDICATOR When the Red Panic button is pressed, the TX LED will flash to indicate the PB-7 is transmitting a signal to the Control Panel. z Battery The Panic Button uses one CR2032 Lithium battery as its power source. The battery is good for at least 5 years before it needs changing. PB-7 can also detect the low battery status. The low battery signal will be sent to the Control Panel along with regular signal transmission for the Control Panel to display the status accordingly. z Getting Started z Remove the screw to separate the top cover from the base. z Insert the battery with negative of the battery on the spring side. z Place the top case over the base and tighten them with the screw. z Put the Control Panel into “Device +/-“ menu and then select “Add Device” menu. z Press any buttons on the PB-7. z Refer to the operation manual of your control panel under the section of “Device +/-“ to complete the learn-in process. z Mounting the PB-7 There are two ways to mount the PB-7 by either Self-adhesive installation or Screw mounting. z Self adhesive installation I. Clean the surface with a suitable degreaser. II. Remove the protective covering from one side of the double-sided adhesive pad and firmly apply to the back of the device. III. Next remove the other cover and firmly press the item onto the desired location. < < N N O O T T E E > > ) Do not use the adhesive pad method of installation on a surface with peeling or cracked paint, or on a rough surface. z Screw Mounting The base has two knockouts, where the plastic is thinner for mounting purpose. To mount the PB-7: I. Remove the screw to separate the top cover from the base. II. Break through the knockouts on the base. III. Using the holes as a template, drill two holes and insert the wall plug. IV. Screw the base into the wall plug. V. Screw the top cover back on to its base z This device complies with Part 15 of the FCC rules and RSS-210 of CANADA. Operations is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may undesired operation. 2

AlarmForce Industries Inc. 675 Garyray Dr. North York ON M9L 1R2 Canada 12/11/2007 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: We, the undersigned, hereby authorize ETS Product Service (Taiwan) CO., LTD. to act on our behalf in all matters relating to applications for“PANIC BUTTON” (Model No.: PB-7, FCC ID: SJLPB7315)” authorization, including the signing of all documents relating to these matters. Any and all acts carried out by ETS Product Service (Taiwan) CO., LTD. on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name: Mourad M’Hiri Title: Manager of Technical Services Company: AlarmForce Industries Inc.

AlarmForce Industries Inc. 675 Garyray Dr. North York ON M9L 1R2 Canada Federal Communications Commission FCC ID: SJLPB7315 Dear Sir: This is to request confidentiality on information submitted for above application. We would like to request confidentiality on some exhibits we submitted for above original application for the reason of trade secret. If those exhibits are available for public inspection, any person who once gets the information contained in those exhibits will be able to design and to make the same products very easily. This is a very serious problem and huge loss for us, because we did invest so much on it. Please be not made the Exhibit Types listed below routinely available for public inspection. Confidentiality Request regarding application for certification of FCC ID: SJLPB7315 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Block diagram, schematics, operational description By: By: Mourad M'Hiri (Signature) (Printed) Title : Manager of Technical Services Applicant : AlarmForce Industries Inc. Address : 675 Garyray Dr. North York ON M9L 1R2 Canada Tel : 1-416-445-1547 Fax: 1-416-445-9381 Date : December 11, 2007

Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Appendix page 12 of 17 Pictures External Photos Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Appendix page 13 of 17

貼於產品本體之標籤圖解 28mm Model: PB-7 FCC ID. : SJLPB7315 IC : 5362A-PB7315 THIS DEVICE COMPLIES WITH PART 15 OF THE FCCRULES AND RSS-210 OF CANADA. OPERATIONS IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: ( 1 ) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE ( 2 ) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFEERENCE THAT MAY UNDESIRED OPERATION . MADE IN TAIWAN 27mm Stick on the back of product

Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Appendix page 14 of 17 Internal Photos Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Appendix page 15 of 17 Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Appendix page 16 of 17

of Applicant: AlarmForce Industries Inc. Address: 675 Garyray Dr. North York ON M9L 1R2 Canada Tested and Prepared by ETS Product Service (Taiwan) Co., Ltd. FCC Registration No.: 930600 Industry Canada filed test laboratory Reg. No. IC 5679 A2LA Accredited No.: 1983.02 PTCRB Accredited Type Certification Test House FCC ID: SJLPB7315 Report No.: W6M20712-8741-C-1 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] FCC PART 15 SUBPART C TEST REPORT for PANIC BUTTON Model No.: PB-7 Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Page 1 of 20 TABLE OF CONTENTS 1 General Information 2 1.1 Notes 2 1.2 Testing laboratory 3 1.2.1 Location 3 1.2.2 Details of accreditation status 3 1.3 Details of approval holder 3 1.4 Application details 4 1.5 Test item 4 1.6 Test standards 5 2 Technical test 5 2.1 Summary of test results 5 2.2 Test environment 5 2.3 Test Mode 5 2.4 Test equipment utilized 6 2.5 General Test Procedure 8 3 Test results (enclosure) 9 3.1 Transmission Requirements 10 3.1.1 Limit of Transmission Time 10 3.1.2 Active Time 10 3.2 Output Power (Field Strength) 11 3.3 Out of Band Radiated Emissions 12 3.4 Transmitter Radiated Emissions in restricted Bands 13 3.5 Spurious Emission radiated, Transmitter 14 3.6 Channel Bandwidth 16 3.7 Antenna requirement 17 3.8 Duty Cycle 18 3.9 Conducted Measurement at (AC) Power Line 19 Appendix 20 Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Page 2 of 20 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the ETS Product Service (Taiwan) Co., Ltd. Tester: December 11, 2007 Jay Chaing Date ETS-Lab. Name Signature Technical responsibility for area of testing: December 11, 2007 Steven Chuang Date ETS Name Signature Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Page 3 of 20 1.2 Testing laboratory 1.2.1 Location OATS No.5-1, Shuang Sing Village, LiShuei Rd., Wanli Township, Taipei County 207, Taiwan (R.O.C.) Company ETS Product Service (Taiwan) Co., Ltd. 6F, NO. 58, LANE 188, RUEY-KUANG RD. NEIHU, TAIPEI 114, TAIWAN R.O.C. Tel : 886-2-66068877 Fax : 886-2-66068879 1.2.2 Details of accreditation status Accredited testing laboratory A2LA accredited number: 1983.02 FCC filed test laboratory Reg. No. 930600 Industry Canada filed test laboratory Reg. No. IC 5679 PTCRB Accredited Type Certification Test House Town: ./. Country: ./. Telephone: ./. Fax: ./. 1.3 Details of approval holder Name: AlarmForce Industries Inc. Street: 675 Garyray Dr. North York ON M9L 1R2 Town: ./. Country: Canada Telephone: 1-416-445-1547 Fax: 1-416-445-9381 Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Page 4 of 20 1.4 Application details Date of receipt of test item: December 7, 2007 Date of test: from December 7, 2007 to December 11, 2007 1.5 Test item Description of test item: PANIC BUTTON Type identification: PB-7 Brand name: AlarmForce Multi-listing model number: without Transmitting frequency: 315 MHz Operation mode: simplex Voltage supply: CR2032 3V Lithium battery (If the device is using battery, please check if the device is tested under fresh battery condition.) Highest clock frequency: 315 MHz Antenna type: PCB antenna Photos: see Appendix Manufacturer (if applicable) Name: ./. Street: ./. Town: ./. Country: ./. Additional information: ./. Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Page 5 of 20 1.6 Test standards Technical standard : FCC RULES PART 15 SUBPART C § 15.231 (a) (2007-09) 2 Technical test 2.1 Summary of test results No deviations from the technical specification(s) were ascertained in the course : of the tests performed. or The deviations as specified in 3 were ascertained in the course of the tests … performed. 2.2 Test environment Temperature: 23 o C Relative humidity content: 20 ... 75 % Air pressure: 86 ... 103 kPa Details of power supply: CR2032 3V Lithium battery 2.3 Test Mode This EUT is the portable device. So the EUT was tested on three different axes. Please see assessment test results as section 3 of this test report. Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Page 6 of 20 2.4 Test equipment utilized No. Test equipment Type Serial No. Manufacturer Cal. Date Next Cal. Date ETSTW-CE 001 EMI TEST RECEIVER ESHS10 842121/013 R&S 2007/10/15 2008/10/14 ETSTW-CE 002 PREREULATOR MODE DC POWER SUPPLY None None Function Test ETSTW-CE 003 AC POWER SOURCE APS-9102 D161137 GW Function Test ETSTW-CE 004 ZWEILEITER-V- NETZNACHBILDUNG TWO- LINE V-NETWORK ESH3-Z5 840731/011 R&S 2007/10/15 2008/10/14 ETSTW-CE 005 Line-Impedance Stabilisation Network NNBM 8126D 137 Schwarzbeck 2007/10/15 2008/10/14 ETSTW-CE 006 IMPULSBEGRENZER PULSE LIMITER ESH3-Z2 100226 R&S In House Certificate ETSTW-CE 008 ABSORBING CLAMP MDS 21 3469 Schwarz…

Text truncated - open the document above for the full version.

Registration number: W6M20712-8741-C-1 FCC ID: SJLPB7315 ETS Product Service (Taiwan) Co., Ltd. Appendix page 17 of 17 Set Up Photos