SKJ-Q5BLUETOOTH SPEAKER

Q5 USER MANUAL Please don’t put the product on wet and raining side when use UNCTION: LINE IN Insert the 3.5mm audio cable to AUX and another connecter to PC or mobile phone of PSP, will auto switch LINE IN mode. 3.5mm stereo audio input ,can connect the laptop ,digital music player and PC. Greeting Words TECHNICAL PARAMETER 03 04050607 080910 75mm 40mm Sling hole On/off Working guiding light Aux audio import jack 1.if at the first time using the product can not turn on, it’s perhaps not enough power for the battery please try to charge the battery then open again 2. please close the machine when the battery charging it’s good for the life of battery, also please use the dedicated equipment for battery charging in the package attached. 3. please charge at least 4hours in the first time using, next time could be 2-3 hours. 4. long time no using product please remember to charge the battery firstly 5. please don’t put product under hot sunshine, near the temperature 45’c and nor can fire, in case the damage happened. 6. please don’t tear open the machine if you are not professional for this machine 7. input voltage of player if too high will be damaged the product, too low will not work 8.if the battery power is low will lead to the button not work or the volume diminution ,and charging will solve the problem. 1.wire Bluetooth play music 2. LINE IN 3. built-in li-battery Charging First time use we suggest to charge the product, please connect with the micro usb between product and computer, charge when off is red indictor, charge finish is blue indictor Connect bluetooth Please turn product “on”( in the same time Please ensure the battery power is full.) it’s have operating prompt sound when the product is ON state, when the TF card, the default for music play mode, long press “M” button or pull out TF card to switch to the Bluetooth mode, will can matching. Connect mobile phone First step Open the bluetooth in your mobile phone, the phone will show the symbol of bluetooth, iphone will enter research the bluetooth mode automatically. Second step Open the bluetooth step up in your mobile phone, point the scan research the equipment Third step If mobile phone show “ERIX AUDIO”,your phone now already found with the bluetooth speaker, then you will enter the matching status. Fourth step During match please input password if needed Fifth step Matching is automatically no need setting, if success, the Bluetooth symbol of your phone Connect computer If your computer is with bluetooth function then you no need set up the bluetooth, if no pls set up the bluetooth driver firstly and insert the bluetooth adapter First step Pls choose bluetooth symbol, chose “add device” Second step The adaptor is searching the bluetooth, until it display ”ERIX AUDIO” Third step Double click “ERIX AUDIO”, it will set up the driver until it set up successfully. Fourth step During match please input password if needed Fifth step If you would like to control last and next song please choose the media player of computer attached itself. (Part mobile phone and online download player can’t support) if bluetooth is not ok pls check if it change to bluetooth mode, if it already is bluetooth model, pls confirm again the bluetooth speaker and computer is connected. Pls also check the equipment manager. Matching and connecting Mobile phone matching---- if last time you did not connect with bluetooth then bluetooth enter matching status, if speaker have been connected, it will connect the equipment same as last time, if not successfully, after 15-30 seconds it will enter the matching status Connecting mode---- start to enter the matching mode Matching status will keep 20-30seconds,if during this period ,equipment in standby state, this time can’t and other bluetooth devices search and connecting. Play music After step up connecting, open the mobile phone or the computer player, play music ,speaker button will control mobile phone music playpauselast song /vol- next song/vol+ so on operate.(part mobile phone and player can’t support ) . Battery specification 3.7v/400mah li-batterymode bl-5b Speaker specification φ40mmdiameter,3w 3.6ω Charge time 2h Frequency response 80hz-15khz Snr ≥80db Distortion thd<1% Usb specification usb2.0compatible withusb1.1 product size φ75mm(diameter)x40mm(high) Use power he product is built-in li-battery ,through the USB cable charge or use DC5V USB power. System form 1. speaker 2. 3.5mm audio line 3. USB cable 4. use manual

Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 EUT View 3 EUT View 4 Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 EUT View 5 EUT View 6 Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 EUT View 7

Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: SKJ-Q5 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: SKJ-Q5 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 Solder Board-Component View 1 Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 Solder Board-Component View 2 Solder Board-Component View 3 Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 Solder Board-Component View 4 Solder Board-Component View 5

RF Exposure Requirements Product Description: Bluetooth speaker Model No.: Q5 FCC ID: SKJ-Q5 According to the KDB-447498 D01 V05, the following RF exposure evaluation shall to demonstrate RF exposure compliance. Bluetooth Tx frequency range: 2402-2480MHz Device category: Portable device (Distance: 5mm) Maximum Conducted Output Power: 0.952 dBm Maximum Antenna Gain: 2 dBi Maximum EIRP Output Power: 1.9733 mW (2.952dBm) Limit: 10mW Source-based time-averaged EIRP output power is 1.9733 mW < 10 mW So the transmitter complies with the RF exposure requirements and the SAR is not required.

Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I PAGE 1 OF 53 FCC PART 15.247 FCC Part 15C Measurement and Test Report For Shenzhen Heui Xint Technology Co., Ltd 2/F, E Building, Huafeng Industry, Hangcheng Road, Xixiang Town, Baoan District,Shenzhen,China FCC ID: SKJ-Q5 FCC Rule(s): FCC Part 15.247 Product Description: bluetooth speaker Tested Model: Q5 Report No.: STR14018019I Tested Date: 2014-01-02 to 2014-01-17 Issued Date: 2014-01-17 Tested By: Daniel Liu / Engineer Reviewed By: Lahm Peng / EMC Manager Approved & Authorized By: Jandy so / PSQ Manager Prepared By: Shenzhen SEM.Test Technology Co., Ltd. 1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen SEM.Test Technology Co., Ltd. Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I PAGE 2 OF 53 FCC PART 15.247 TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................... 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ....................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 6 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 7 3. RF EXPOSURE ......................................................................................................................................................... 8 3.1 STANDARD APPLICABLE ......................................................................................................................................... 8 3.2 TEST RESULT.......................................................................................................................................................... 8 4. ANTENNA REQUIREMENT .................................................................................................................................. 9 4.1 STANDARD APPLICABLE ......................................................................................................................................... 9 4.2 EVALUATION INFORMATION .................................................................................................................................. 9 5. FREQUENCY HOPPING SYSTEM REQUIREMENTS ................................................................................... 10 5.1 STANDARD APPLICABLE ....................................................................................................................................... 10 5.2 FREQUENCY HOPPING SYSTEM............................................................................................................................. 10 5.3 EUT PSEUDORANDOM FREQUENCY HOPPING SEQUENCE .................................................................................... 11 6. QUANTITY OF HOPPING CHANNELS AND CHANNEL SEPARATION ................................................... 12 6.1 STANDARD APPLICABLE ....................................................................................................................................... 12 6.2 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 12 6.3 TEST PROCEDURE ................................................................................................................................................. 12 6.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 12 6.5 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 13 7. DWELL TIME OF HOPPING CHANNEL .......................................................................................................... 17 7.1 STANDARD APPLICABLE ....................................................................................................................................... 17 7.2 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 17 7.3 TEST PROCEDURE ................................................................................................................................................. 17 7.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 17 7.5 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 18 8. 20DB BANDWIDTH ............................................................................................................................................... 28 8.1 STANDARD APPLICABLE ....................................................................................................................................... 28 8.2 TEST EQUIPMENT LIST…

Text truncated - open the document above for the full version.

Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Conducted Emission Test Setup Radiation Emission Test Setup (30MHz to 1GHz) Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 Radiation Emission Test Setup (Below 30MHz) Radiation Emission Test Setup (30MHz to 1GHz) Shenzhen Heui Xint Technology Co., Ltd Model: Q5 REPORT NO.: STR14018019I FCC PART 15.247 Radiation Emission Test Setup (Above 1GHz)