SP9-00005Bluetooth Speaker

Introduction Thank you for purchasing the Altec Lansing Solo Jacket IMW375 Bluetooth Speaker. You can use this speaker to listen to audio wirelessly from devices such as smart phones, computers, iPods, tablets and most other Bluetooth sound sources. Furthermore you can pair two Solo Jacket speakers to your Bluetooth device simultaneously for true stereo sound. Please read this manual carefully FIRST in order to get the most out of your speaker. Please note the Solo Jacket speaker is rated IPX67 waterproof, shockproof, dustproof. The Solo Jacket can be submerged under water 3 feet for up to 30 minutes but the waterproof cover on the back must be fully closed otherwise any damage caused by water will not be covered under warranty. Important Safety Precautions When using your speaker basic safety precautions should always be followed, including the following: 1. READ ALL INSTRUCTIONS BEFORE USING YOUR SPEAKER. 2. Never expose your speaker to high temperatures. 3. In order to avoid the risk of electric shock, never attempt to open your speaker or repair it without the assistance of certified professionals. 4. If you do not intend on using your speaker for an extended period of time, please unplug the AC power adapter from the power outlet and also disconnect it from your speaker. Features -Seamlessly stream music from your iPad, iPhone, Android device, laptop, tablet or other Bluetooth enabled device that support the A2DP profile. - Waterproof, Dustproof, Shockproof, Sandproof - Can be used in conjunction with a second unit to create true stereo sound Package Contents 1. Altec Lansing Solo Jacket IMW375 Bluetooth Speaker 2. Carry Pouch 3. USB Charging Cable 4. Karabiner Clip 5. 3.5mm Auxiliary Cable 6. Extra Skin Jacket 7. Owner’s Manual with Warranty Information Technical Specifications - Battery Life: up to 6 hours - Charging Your Speaker 1. Connect one end of the included USB charging cable to the IMW375 DC input jack. Then plug the other end of the cable into an available USB port on your computer to recharge your speaker’s internal rechargeable battery. NOTE: The internal battery of your speaker takes approximately four hours to charge when completely drained. 2. When charging, a red LED light will illuminate to indicate that the unit is charging. The red light will turn off when your unit is fully charged. Remarks : The USB port is for charging use only, no data transmission functionality Understanding the LED Status Indicators Power and Bluetooth Indicator Light Blinking Green LED = Your speaker is powered ON and ready for Bluetooth pairing with another Solo Jacket speaker for true stereo sound. Blinking Blue LED = An individual Solo Jacket speaker is ready to be paired with your Bluetooth device for MONO sound, or a pair of Solo Jacket speakers are ready to be paired with your Bluetooth device for STEREO sound. Charging Indicator Lights Solid Red LED = Charging Red LED OFF = Battery fully charged. Powering Your Speakers ON & OFF 1. Press and hold the “POWER” button for 3 seconds to turn on your speaker. The LED light will start blinking slowly and the speaker will say, “Powering On”. Now you are ready to pair your audio source with your IMW375 speaker. 2. Press and hold the “POWER” button for 3 seconds to turn off the unit. The speaker will say, “Powering Off” Power Saving Mode The IMW375 will enter a power saving mode if no audio is played for 30 minutes. Press and hold the power button for two seconds to wake the IMW375. Setting Up Your IMW375 Bluetooth Music Receiver Bluetooth Device Compatibility Your speaker connects with all Bluetooth devices that support the A2DP profile including iPads, iPhones, iPod touches, and most smart phones, laptops and tablets. Pairing a Bluetooth Device with Your Speaker Press and hold the “POWER” button for two seconds to turn on the unit. The speaker’s LED light will start blinking slowly. Now you are ready to pair your Bluetooth device with your IMW375 speaker. 1. Go to the Bluetooth Manager of your Bluetooth device. 2. Search Bluetooth devices and select “IMW375” to start connecting. 3. Enter “0000” if your device asks for the PIN code. 4. Once paired, the speaker will say, “You are now paired, enjoy” and the Blue LED light will turn on steadily. 5. Although the speaker can only stream audio from one device at a time, it is capable of being paired with up to eight devices. This means that you only have to enter the PIN code no more than one time for each device. Playing Audio from Your Bluetooth Device 1. Once your Bluetooth device is paired with your IMW375 speaker, simply start playing the music, movie or game and all the audio will automatically be played through the IMW375. 2. Press “POWER” to play/pause the audio. 3. Press + or - to adjust the volume level of the unit. 4. Keep in mind that the IMW375 has a 30 foot Bluetooth wireless range. Note: The volume controls on your media device work separately from the volume controls on the IMW375. When there is an incoming call: 1. Press the “Power” button to pick up the call. 2. Press and hold the “Power” button to reject the call. 3. During the call: Press the “Power” button to hang up the call. To Disconnect Your Bluetooth Device Turn off the paired Bluetooth device or press the Volume “+” and “-“ buttons simultaneously to disconnect the Bluetooth device from your speaker. Your speaker will power off automatically. Reconnecting Your Device If you move out of range or turn off the Bluetooth feature on your device, the unit will disconnect from your device. To reconnect, simply access the Bluetooth Manager on your device and select IMW375. You will not be asked to enter the PIN code again. Out of Range or Lost Signal If your Bluetooth device is out of range (beyond 30 feet) of your speaker or if there is something blocking the Bluetooth signal, the LED light will flash slowly to indicate that the Bluetooth connection with the Bluetooth device has been lost. To avoid a lost connection: 1. Move the …

Text truncated - open the document above for the full version.

KYSHO Federal Communications Commission Authorization and Evaluation Division Confldentiality Request regarding application for certification of FCC ID: SP9-00005 Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, we hereby request confidential treattnent of information accompanying this application as outlined below: KYSHO Multimedia LTD. Flat F 5/F Valiant Industrial Centre, 2-12 Au Pui Wan Street, Fo Tan, Shatin, N. T., Hong Kong File Name Block Diagram.pdf Schematics.pdf Operati onal Description. pdf Tel. : (852) 2799 2895 (3 Lines) Fax : (852) 2755 0533 Exhibit Type B loclt Diagram Schematics Operat ional Description ,,. -ail]' - * .\ r> T'he above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant 1br this application. Address: Flat F, S/q',Valiant Industrial Ctr,2-12, AuPui Wan St, Fo Tan, HK l'el: 852-2799 2895 Fax: 852-2799 0533 Erlai I : kysholtd@netvi gator.com Sirrcerely,,

KYSHO KYSHO Multimedia LTD. Flat F 5/F Valiant Industrial Centre, 2-12 Au Pui Wan Street. Fo Tan, Shatin, N T , Hong Kong AGENCY AUTHORIZ NIION LETTER Tel. : (852) 2799 2895 (3 Lines) Fax : (852) 2755 0533 Federal Communications Commission Authorization and Evaluation Division FCC ID: SP9-00005 To whom it rnay concern: Date: 201414111 We. the undersigned, hereby authorize Richard Li from SGS-CSTC Standards Technical Services Co., Ltd. to act on our behalf, as our agent, in the following matters related to the FCC approval of : oLrr product: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried oLrt by Richard Li within the scope of this authorization shall have the same effects as our own. -' --,-:-*;_]'-'-. - .* ?> This authorization shall expire 6 months from original date. If you have any questions regarding tlre ar-rthor ization,please don't hesitate to contact us. -fhank you. Address: Flat F, S/F,Valiant Industrial Ctr, 2-l2,Au Pui Wan St, Fo Tan, HK 'l'el 852-2799 2895 F-ax: 552-279\0533 E mai I :kysho ltd@netvi gator. com S irrcerely, ane ll.rfle Akiyuki Yasuda/ President Cgrfpany Name: Kysho Multimedia. Registelctl (ftficc: Fllt/Rm 60l, 6/F., (l (

External Photo

antenna for RF

Internal Photo

SGS-CSTC Standards Technical Services Co., Ltd. Application No..: GZEM1403000783RF Page: 1 of 1 FCC ID: SP9-00005 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. RF Exposure Compliance Requirement The product belongs to standalone portable device base the FCC rule part 2.1091&2.1093. The transmission frequencies of the device are between 100 MHz and 6 GHz. The worst case test separation distance is 5mm. The Max Conducted Output Power and SAR Test Exclusion Threshold (mW) are listed below: Transmit frequency (GHz) Max Conducted Output Power (mW) SAR Test Exclusion Threshold (mW) 2.402 1.29 9.7 2.441 1.38 9.6 2.480 1.30 9.5 The SAR Test Exclusion Threshold for 100 MHz to 6 GHz is calculated from: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. According to SAR Exclusion Threshold in KDB 447498D01 v05 r02 General RF Exposure Guidance v05, the SAR report is not required.

SGS-CSTC Standards Technical Services Co., Ltd. 19 8 Ke zhu Roa d, Scient ech Park, Guangzhou Economic & Technolo gical De velopment D istrict, Guangzhou, China 510663 Telephon e: +86 (0) 20 8 2155555 Fax: +86 (0) 20 820750 59 Email: ee. guangzh [email protected] Report No.: GZEM140300078301 Page: 1 of 72 FCC ID: SP9-00005 Authorized Signature: Richard Li Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1403000783RF Applicant: Kysho Multimedia Ltd. FCC ID: SP9-00005 Product Name: Bluetooth Speaker Product Description: Bluetooth speaker with 2.4 GHz as carrier Model No.: AP-155TW Customer Model: IWM375 Trade Mark: ALTEC Standards: 47 CFR PART 15 Subpart C: 2013 section 15.247 Date of Receipt: 2014-03-05 Date of Test: 2014-03-06 to 2014-04-01 Date of Issue: 2014-04-17 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further detail. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140300078301 Page: 2 of 72 FCC ID: SP9-00005 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-04-17 Original Authorized for issue by: Tested By 2014-03-06 to 2014-04-01 (Jack Liang) / Project Engineer Date Prepared By 2014-04-10 (Jack Liang) / Project Engineer Date Checked By 2014-04-17 (Storm Shu) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140300078301 Page: 3 of 72 FCC ID: SP9-00005 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 3 Test Summary Test Test Requirement Test method Result Antenna Requirement FCC PART 15 C section 15.247 (c) and Section 15.203 FCC PART 15 C section 15.247 (c) and Section 15.203 PASS Occupied Bandwidth FCC PART 15 C section 15.247 (a)(1) ANSI C63.10: Clause 6.9.1…

Text truncated - open the document above for the full version.

Test setup Photo 1.1 RADI ATE D SP URI OU S EM ISSIO N TE ST SETUP 30 MHz to 1 GHz: Above 1 GHz: 1.2 CON DU CTED EM ISSI ON TEST SETUP