SSNCM1400Wireless MOUSE

USER MANUAL MAX61969466 / UO4C19TQA CM-1300 CM-1400 CM-1400 2.4 GHz WIRELESS MOUSE CM-1300 1) Please load the battery based on “+/-” direction shown at the place for mouse battery installation. Product use method 2) Please turn the power switch on the baseboard of the mouse to be “ON”. Off / On — CM-1300 — CM-1400 On On 1) Mouse (CM-1400) Right button DPI adjusting key (CM-1400) On /off Key Roller Right arrow Battery Lid Left button Left arrow Receiver Storage Space 3) User Manual 4) Battery (AA x 2) 2) Receiver (Receiving Equipment) •The storage space to prevent the receiver from being lost 1) Mouse (CM - 1300) Right button Right arrow Battery lid Roller Left arrow Receiver storage space Left button On-off key 4) Battery (AA x 1) 3) User Manual 2) Receiver (receiving equipment) • The storage space to prevent the receiver from being lost Appearance and components Appearance and components For your safety, please be sure to observe the following instructions. “Please be sure to read the safety precautions before use and use correctly” “After reading the manual, please be sure to keep it in a readily accessible place.” The safety precautions noted below are for safe and correct use of the product to prevent unexpected danger or damage beforehand. This is the sign to draw attention to dangerous matters and operations. In order to avoid danger, be sure to carefully read the parts with the sign and follow the instructions. Note : Violation of these instructions may cause minor injury or product damage. •Prior to using and unplugging the product, please be sure to familiarize yourself with the method in the manual. Misuse may cause malfunction and poor boot-up. •Please do not arbitrarily disassemble, alter and repair the product. This will cause malfunctions and security threats, which are ineligible for A/S. •Please do not pour liquid on the product. This will be a cause for malfunction and poor boot-up. •Please do not press the product and the keys too hard. This will be a cause for malfunction and poor boot-up. •Please neither over-bend the power cord nor pull it too hard. This will be a cause for malfunction and poor boot-up. 1. The battery attached is not rechargeable. If it is charged, an explosion may occur. 2. Avoid impacting on batteries or the mixed use of batteries of different models which may lead to battery leakage or explosion. 3. Attention! Leaked electrolyte is corrosive. Warranty : Violation of these instructions may cause serious injury or death. •In case of smoking, or smelling or sounding weird, please stop using the product and immediately disconnect it from your computer. This will be a cause for fire and electric shock. •Please do not use the product wetted by liquid. There is a risk of fire or electric shock. •In order to protect vision, please do not shine the LED light emitted from the bottom of optical mouse and the beam of laser mouse at your eyes. This will be a cause for vision loss or blindness. •Please avoid using the mouse for a long time, which may cause serious injury or disorder. •Using computer excessively, you may suffer from fatigue in your hands, feet, shoulder, neck or other parts of your body. •Persistent fatigue may be a cause for such muscle injuries as carpal tunnel syndrome (CTS), etc. and myelodysplastic syndrome (MSD). •If you feel tired or uncomfortable, we recommend that you consult a doctor nearby. •IR LED is adopted so that LED light can not be seen. To protect your eyes, don’t stare at the bottom for long time. (For CM-1300 and CM-1400) 2.4 GHz WIRELESS MOUSE USER MANUAL02EnglishEnglish2.4 GHz WIRELESS MOUSE USER MANUAL03 2.4 GHz WIRELESS MOUSE USER MANUAL04EnglishEnglish2.4 GHz WIRELESS MOUSE USER MANUAL05 2.4 GHz WIRELESS MOUSE USER MANUAL06EnglishEnglish2.4 GHz WIRELESS MOUSE USER MANUAL07 2.4 GHz WIRELESS MOUSE USER MANUAL08EnglishEnglish2.4 GHz WIRELESS MOUSE USER MANUAL09 2.4 GHz WIRELESS MOUSE USER MANUAL10EnglishEnglish2.4 GHz WIRELESS MOUSE USER MANUAL11 3) As shown in figure below, please insert the receiver in the computer and wait for the completion of the driver installation. (Don’t remove the receiver in the driver installation process) The attached battery will start slow discharge from the date of ex-factory. Besides, the service life of the battery is also affected by the use time and environment. The service life of the battery may also be shortened if it is stored at the place with extremely low temperature. For long time no use of the product, please remove the battery for proper storage; otherwise, product fault may be caused by battery leakage. Since IR LED is adopted by the product, no LED light will be seen even when the product is powered on. In this case, it is also operating normally on the computer. Please note that it is not a fault. Different from ordinary optical LED, IR LED can achieve stable operation effect through infrared ray and can lower the power consumption of the battery through the feature of no light. Product use method •The mouse is connected to a vacant USB port of a power-off computer. •The mouse will be identified automatically after the computer is powered on. (In case the O/S of your computer is password protected, please wait till the computer boots up completely before connecting the mouse.) •In case the mouse is connected to a USB port of a running computer, a driver will be installed and the mouse will be identified automatically. The way to connect the mouse to the computer Important : when install the driver, please wait until the display of the installation completion information. •When the mouse is not used or moved, please remove the receiver from the computer and then store it in the receiver storage space at the bottom of the mouse as shown in figure below to prevent it from being lost. How to store the receiver Insert the receiver Power on the mouse ON CM-1300CM-1400 How to connect the receiver in the computer Matters related to the service life of the battery 1) The service life …

Text truncated - open the document above for the full version.

LG Electronics Inc. 50 Hyangjeong-dong, Heungdeok-gu, Cheongju-si, Chungcheongbuk-do, 361-480, Korea March 06, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA DECLARATION FOR ADDITIONAL FREQUENCY HOPPING REQUIREMENTS To whom it may concern: We hereby declare that the device of SSNCM1400 meet following FCC requirements of the Section 15.247(a)(1) : 1. The hopping sequence is pseudorandom. 2. All channels are used equally on average. 3. The receiver input bandwidth approximately equal the transmit bandwidth. 4. The receiver hop in sequence with the transmit signal. Sincerely, Kang O-Byoung Senior Engineer

LG Electronics Inc. 50 Hyangjeong-dong, Heungdeok-gu, Cheongju-si, Chungcheongbuk-do, 361-480, Korea Date: February 18, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards;

LG Electronics Inc. 50 Hyangjeong-dong, Heungdeok-gu, Cheongju-si, Chungcheongbuk-do, 361-480, Korea Date: March 06, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: SSNCM1400 To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics Inc. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics Inc. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Operational Description 3 Schematics 4 Part Lists SHORT-TERM 5 Internal Photos 6 External Photos 7 Test-Setup Photos 8 Users Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Kang O-Byoung Senior Engineer

LG Electronics Inc. 50 Hyangjeong-dong, Heungdeok-gu, Cheongju-si, Chungcheongbuk-do, 361-480, Korea Date: March 06, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA LETTER OF AUTHORIZATION We, the undersigned, hereby authorize Harvey Sung of Digital EMC Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: SSNCM1400 including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of Digital EMC Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from LG Electronics Inc. Sincerely, Kang O-Byoung Senior Engineer

FCCID: SSNCM1400 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 1 FCCID: SSNCM1400 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 2 FCCID: SSNCM1400 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 3

FCC ID: SSNCM1400 Copyright Ⓒ 2013, Digital EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase - The FCC label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. - The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the user's manual.

FCCID: SSNCM1400 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 1 FCCID: SSNCM1400 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 2 FCCID: SSNCM1400 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 3 FCCID: SSNCM1400 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 4

MHzmm = ± =[ / ]*[√ ] = Thus SAR for this device is not required. [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW 5 Step 2-1) SAR test exclusion thresholds for 100MHz to 1500MHz at test separationn distances > 50 mm = N/A 0.62 ≤ 3, for 1g SAR Copyright Ⓒ 2013, Digital EMC Co., Ltd. Step 2-2) SAR test exclusion thresholds for 1500MHz to 6GHz at test separationn distances > 50 mm = N/A 2403 - Min. test separation distance = mW -1.90 1.50 dBm - Min. transmitting frequency = dB Typical Power:Measured Power: -1.00 dBm 2.50 dBm SSNCM1400 2.00 2.403 5 - Max. power with turn-up tolerance = 2 Used Step 1) SAR test exclusion thresholds for 100MHz to 6GHz at te st separationn distances ≤ 50 mm = [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] FCC ID : Standalone SAR test exclusion considerations April 18, 2013

DEMC1301-00139 &DEMC1301-00140 FCCID: SSNCM1400 Report No.: DRTFCC1303-0244(1) IC: 2703H-1303CM1400 TRF-RF-212(00)101214 Page2 / 35 Copyright ○ C 2013, Digital EMC Co., Ltd. Test Report Version Test Report No. Date Description DRTFCC1303-0244 Mar. 12, 2013Initial issue DRTFCC1303-0244(1) Apr. 18, 2013 Update Test Result and Test Equipment List DEMC1301-00139 &DEMC1301-00140 FCCID: SSNCM1400 Report No.: DRTFCC1303-0244(1) IC: 2703H-1303CM1400 TRF-RF-212(00)101214 Page3 / 35 Copyright ○ C 2013, Digital EMC Co., Ltd. Table of Contents 1. General Information ............................................................................................................... 5 1.1 Testing Laboratory ........................................................................................................ 5 1.2 Details of Applicant ....................................................................................................... 5 1.3 Description of EUT ........................................................................................................ 5 1.4. Declaration by the manufacturer ................................................................................... 5 1.5. Supportedchannels ......................................................................................................... 5 1.6. Test Equipment List ........................................................................................................ 6 1.7. Summary of Test Results ................................................................................................ 7 1.8 Conclusion of worst-case and operation mode ............................................................ 8 2. Transmitter Radiated Spurious Emissions and Conducted Spurious Emission ............ 9 2.1. Test Setup ......................................................................................................................... 9 2.2. Limit .................................................................................................................................. 9 2.3. Test Procedures ............................................................................................................ 10 2.3.1. Test Procedures for Radiated Spurious Emissions .............................................. 10 2.3.2. Test Procedures for Conducted Spurious Emissions .......................................... 10 2.4. Test Results .................................................................................................................... 11 2.4.1. Radiated Emission .................................................................................................... 11 2.4.2. Conducted Spurious Emissions ............................................................................. 12 3. Carrier Frequency Separation ............................................................................................. 18 3.1.Test Setup ..................................................................................................................... 18 3.2. Limit ................................................................................................................................ 18 4. Number of Hopping Frequencies ..................................................................................... 20 4.1.Test Setup ..................................................................................................................... 20 4.2. Limit ................................................................................................................................ 20 5. 20dBc BW .............................................................................................................................. 22 5.1. Test Setup ....................................................................................................................... 22 5.2. Limit ................................................................................................................................ 22 5.3. Test Procedure ........................................................................................................... ... 22 5.4. Test Results .................................................................................................................... 22 6. Time of Occupancy (Dwell Time) ........................................................................................ 25 6.1. Test Setup ....................................................................................................................... 25 6.2. Limit ................................................................................................................................ 25 6.3. Test Procedure .............................................................................................................. 25 6.4. Test Results .................................................................................................................... 25 7. Maximum Peak Output Power Measurement .................................................................... 27 7.1. Test Setup ....................................................................................................................... 27 7.2. Limit ................................................................................................................................ 27 7.3. Test Procedure ............................................................................................................... 27 7.4. Test Results .................................................................................................................... 28 8. Transmitter AC Power Line Conducted Emission ............................................................ 31 DEMC1301-00139 &DEMC1301-00140 FCCID: SSNCM1400 Report No.: DRTFCC1303-0244(1) IC: 2703H-1303CM1400 TRF-RF-212(00)101214 Page4 / 35 Copyright ○ C 2013, Digital EMC Co., Ltd. 8.1. Test Setup .......................................................…

Text truncated - open the document above for the full version.

FCC ID: SSNCM1400 Copyright Ⓒ 2013, Digital EMC Co., Ltd. EUT Position EUT Position: X-axis EUT Position: Y-axis EUT Position: Z-axis FCC ID: SSNCM1400 Copyright Ⓒ 2013, Digital EMC Co., Ltd. 1GHz-18GHz