STESN-NOTCH-43-CWireless CDMA Booster

Quick Guide Please read this manual before operating this product. $IWHU\RX¿QLVKUHDGLQJWKLVPDQXDOVWRUHLWLQDVDIHSODFHIRUIXWXUHUHIHUHQFH RSN-NOTCH-43-C Address: R-tron Inc. 6402 College Boulevard, Overland Park, KS 66211 Phone: +1-913-344-9977, 1-888-31R-TRON Fax: +1-913-344-9988 e-mail: [email protected] Website: www.r-tron.com 1 Quick Guide Introduction Introduction NOTCHCELL repeater can be used in CDMA service shaded areas like in-buildings, underground and tunnels to cover its service area. This repeater system designed for dual and simultaneous service, namely, it receives signals from the base station through donor antenna, amplifies the signals and re-transmits it to one or other mobile stations. - NOTCHCELL utilizes the web-based user interface and web server to support the remote access. There are two physical LAN ports: • The Local port provides the wireless on-site access to the repeater. The two ports allow local and remote users to access the repeater simultaneously. - DHCP server at the Local port enables Plug and Play by automatically assigning the IP address to the user’s computer. - Parameter setup is only one click away – • Automatic Easy Setup feature will measure the isolation and limit the maximum gain accordingly. This will also enable Auto Level Control as well as Auto Shut Down. These two features are strongly recommended to prevent the uncontrolled power output, which could have an adverse impact on the RF network and the repeater. For example, ALC will automatically apply attenuation when the input signal strength is increased due to the new base station deployment near the repeater site. • R-tron implemented intelligent design in the NOTCHCELL as following: ƇProgrammable Bandwidth and Band » 5, 10, 15, and 20 MHz contiguous and non-contiguous segments » Any Band Combination within 65MHz PCS Band [A,D,B,E,F,C,G] » Three (3) 5MHz segments Ƈ Remote Access and Control ƇBuilt in CDMA MODEM Ƈ(DV\DQG4XLFN,QVWDOODWLRQ ª:HEEDVHG*8, » Plug and Play - DHCP Server @ Local Port » Automatic Easy Setup (Recommended) » ,VRODWLRQ'HWHFWLRQ » WiFi Access on site ƇAuto Level Control & Auto Shut Down NOTCH antenna (Sold separately) A NOTCH antenna has great front-back ratio and ensures the better isolation between the Donor Antenna and Server Antenna. It is optimized for the NOTCHCELL models. It is recommended to use the NOTCH antenna when installing the NOTCHCELL models. 2 The installation procedure is as follows: 0RXQWLQJĺ*URXQGLQJĺ5)&RQQHFWLRQĺ3RZHU2Q First of all, check list of items: Repeater (1), AC Cord (1), Anchor Bolts (4), WiFi Antenna (1), UTP Cross LAN Cable (1), Quick Guide (1), User’s Manual (1) Hardware Installation Fixate the mounting bracket onto the structure using provided bolts or extra screws. 2 Mounting Step 1 Lean the NOTCHCELL to hang the topside of the Guide Ring on the mounting bracket, and push towards the structure to mount. Step 2 3 Quick Guide Hardware Installation Fix the NOTCHCELL using 16 screws provided. Step 3 4 Hardware Installation A rod on the bottom side is intended for a building ground. Connect the ground cable to the rod. 2 Grounding Dangerously high voltages may occur and damage the equipment if the equipment is not grounded properly. Warning 5 Quick Guide Hardware Installation 3 RF Cable Connection Connect a cable from a donor antenna to the DONOR ANTENNA Port. Connect a cable from a repeater’s server antenna to the SERVER ANTENNA Port. Step 2 Step 1 Note Enough isolation? Antenna isolation = Path loss between the server antenna port and the donor antenna port Antenna isolation Repeater max. gain +15dB If antenna isolation < Repeater max. gain +15dB ĺ System oscillation or Low gain ModelMax Gain 95dBRSN-NOTCH-43-C Minimum required isolation (@Max Gain) 110(=95+15) DO NOT connect or disconnect the coaxial cable while the power is on. Warning Repeater Donor Antenna Plugged in an AC outlet Donor Base Station Server Mobile Station Server Antenna Hardware Installation 6 4 Power On Connect the power cord. Align the grooves fit into each other before connecting the power cord. Plug the power cord into a wall outlet. Power Switch turns on. Step 1 Step 2 Step 3 Note It will take approximately 1 minute to boot after turning it on. Attach the WiFi Antenna before turning on the power. How to turn on the power switch 2 1 7 Quick Guide Hardware Installation Match the each groove when connecting the power cord. Check if the Power LED turns on. Attach the WIFI Antenna as shown. Connecting the grooves Step 4 8 1 System Requirements Operation 2.1 Windows XP Click the Start button and 0\1HWZRUN3ODFHV. Step 1 NOTCHCELL operates on a customer provided PC based platform with the following system requirements: • Windows® 2000, Windows® XP or Windows® Vista • Internet Explorer 6.0 (Recommended) or higher • 128 MB RAM or higher • Pentium processor or higher • RJ-45 jack required 2 1HWZRUN6HWXS 9 Quick Guide Operation Click9LHZQHWZRUNFRQQHFWLRQV. Step 2 Right-clickLocal Area Connection to see a shortcut menu and clickProperties. Step 3 To use the wireless network connection, precede the “Step 3” shown in the following and then go to the next Steps. 10 Operation 1) Select,QWHUQHW3URWRFRO 7&3,3 and click Properties. 2) Check 2EWDLQDQ,3DGGUHVVDXWRPDWLFDOO\ and click OK. 11 Quick Guide Operation 3) Click9LHZDYDLODEOHZLUHOHVVQHWZRUNV and then the following screen appears. 4) Double click r-tron and then you will be asked for the network key. Type the network key, “notchcell” and click Connect. 12 Operation 5) Your wireless network connection has been completed if you see theConnected as in the following screen. Right-clickLocal area Connection to see a shortcut menu and click Properties. Step 3 To use the local area network connection, repeat the “Step 1 and 2” in the page 8 and then go to the next Steps. 13 Quick Guide Operation 1) Select,QWHUQHW3URWRFRO 7&3,3 and click Properties. 2) Check 2EWDLQDQ,3DGGUH…

Text truncated - open the document above for the full version.

Jisan IT Venture Center 2,3F, 1004-9,10, Doksan-Dong, Gumcheon-Gu, Seoul, Korea Tel: +82-2-896-4101 Fax: +82-2-896-4107 [email protected] March 05, 2008 Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 In re: R-tron, Inc. FCC ID: STESN-NOCH-43-C WirelessF Booster (CDMA) Part 24 Certification Request for Confidentiality Gentlemen: In accordance with 0.459 of CFR 47, R-tron Inc. hereby requests confidentiality of the Block Diagram, Circuit Diagrams, Repeater Description, Technical Specification, Parts List, Tune-Up Procedure for the above-referenced certification application. These documents contain detailed system and equipment description and related information about the product which R-tron Inc. Considers to be proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, R-tron Inc. considers this information to be of benefit to its competitors, such that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, R-tron, Inc.

RSN-NOTCH-43-C EUT-Photograph *Repeater* <Front View > < Rear View > <Bottom view> <Left side view> <Right side view> < The Inside of the Repeater >

*Total* <Inner View> <Outer View> *MCU Board* *NCU Board* <Top View> <CPU B’D Bottom View> <I’O B’D Top View>

*UDCs* <UL UDC Top View> <UL UDC PCB Top View> <UL UDC BOTTOM View>

<UL UDC BOTTOM View> <DL UDC PCB BOTTOM View> *HPA* <Inner View> <Outer View>

*LPA* *Main AMP, Error AMP* <Inner View> <Outer View> *Detector, Controller* <Inner View> <Outer View> *Pre, Sub* <Inner View> <Outer View>

S PG π4 S PG π4

Product Name Model Name RSN-NOTCH-43-C ͑͑ESTECH CO., LTD. http://www.estech.co.kr FCC TEST REPORT Wireless Booster(CDMA) Report Number : ESTR0803-0271 of 29 Applicant FCC ID STESN-NOTCH-43-C ESTECH CO., LTD Rm. 1015 World Venture Center, 426-5 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea. Tel:82-2-867-3201, Fax:82-2-867-3204 R-TRON, Inc. Report Number : ESTR0803-0271 of 29 FCC ID : STESN-NOTCH-43-C Company Name Address Product Name Model No.Manufacturer Serial No. Country of origin Issued DateTested Date ͑͑ESTECH CO., LTD. http://www.estech.co.kr FCC Test Report Applicant Product Report Number RSN-NOTCH-43-C KOREA R-TRON, Inc. Test Result Pass 2008-03-31 2008-03-06 ~ 2008-03-28 Other ESTR0803-027 Jisan IT Venture Bldg., 2/3F, 1004-9/10, Doksan-Dong, Gumcheon- Gu, Seoul, Korea Wireless Booster(CDMA) NONE R-TRON, Inc. Report Number : ESTR0803-0272 of 29 Rm. 1015 World Venture Center, 426-5 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea. Tel:82-2-867-3201, Fax:82-2-867-3204 ESTECH CO., LTD o This is certified that the above mentioned products have been tested for the sample provided by client. o No part of this document may not be duplicated or reproduced by any means without the express written permission of Estech Co., Ltd. Standard FCC PART 24 Subpart E Tested by Approved by I.K. Hong/ Engineer (Signature) Eun-young Son/ Engineering Manager (Signature) Report Number : ESTR0803-0272 of 29 FCC ID : STESN-NOTCH-43-C 1. General Information Page 4 2. Laboratory Information Page 5 3. Summary of Test Results Page 5 4. RF Output Power Page 6 5. Occupied Bandwidth Page 11 6. Spurious and Harmonic Emission at Antenna Terminal Page 14 7. Field Strength of Spurious Radiation Page 24 8. Frequency stability Page 27 Contents ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0803-0273 of 29Report Number : ESTR0803-0273 of 29 FCC ID : STESN-NOTCH-43-C 1. General Information 1.1 EUT Description Channel Uplink :1851.25 ~ 1908.75MHz Uplink&Downlink(25/600/1175) CDMA Frequency Downlink :1931.25 ~ 1988.75MHz Input: 110VAC(85 ~ 145VAC), Output: DC 7V Power Rating ͑͑ ESTECH CO., LTD. http://www.estech.co.kr FCC ID STESN-NOTCH-43-C Modulation Type Product Name Model Name Wireless Booster(CDMA) RSN-NOTCH-43-C Report Number : ESTR0803-0274 of 29Report Number : ESTR0803-0274 of 29 FCC ID : STESN-NOTCH-43-C 2. Laboratory Information 3. Summary of Test Results Result 2.4 Major Accredited Mark Test Item EMC Lab(Ichon) EMC Lab(Yanggi) Standard ͑͑ ESTECH CO., LTD. http://www.estech.co.kr 58-1, Osan-Ri, GaNam-Myon, YeoJoo-Gun, KyungKi-Do, Korea 97-1, Hoiuk-Ri Majang-Myon, Icheon-city, KyungKi-Do, Korea 2.1 Laboratory Name 2.2 Location 2.3 Quality System Estech Co., Ltd. Rm. 1015, World Venture Center II, 426-5 Gasan-dong Geumcheon-gu, Seoul, 153-803. Korea. Accredited by KOLAS(ISO/IEC 17025) Head Office PASS PASS PASS PASS PASS RF Output Power Occupied Bandwidth PASS 2.1046 2.1049 2.1051 Field Strength of Spurious Radiation Frequency stability Spurious and Harmonic Emission at Antenna Terminal Modulation Characteristics2.1047 2.1053 2.1055 Report Number : ESTR0803-0275 of 29 FCC ID : STESN-NOTCH-43-C 4. RF Output Power 4.1 Test Procedure 4.2 Test Equipments The following test equipments are used during tests Manufacturer Agilent ͑͑ ESTECH CO., LTD. http://www.estech.co.kr Signal GeneratorE4432B Equipment Spectrum Analyzer Power output shall be measured at the RF outut terminals when the transmitter is adjusted in accordance with the tune-up procedure to give the values of current and voltage on circuit elements as specified. The electrical characteristics of the radio frequency load attached to the output terminals when this test is made shall be stated Model E4407B HP Report Number : ESTR0803-0276 of 29 4.3.1 Test Results (Uplink) Conducted power Low25 Mid.600 High1175 28.08 27.91 1851.2528.42 Freq (MHz)Power Output (dBm)Ch No. 1880.00 1908.75 Report Number : ESTR0803-0276 of 29 FCC ID : STESN-NOTCH-43-C 4.3.2 Test Results (Downlink) Low25 Mid600 High1175 ͅΟ ΁ΦΥ΀ΦΥ ΡΦΥ ͅΟ ΁ΦΥ΀ΦΥ ΡΦΥ ΆΡΝΚΟΜ͑ͩͦͣͦ͢͢͟;͹Ϋ͵ΠΨΟΝΚΟΜ͑ͪͤͣͦ͢͢͟ ͑͑ ESTECH CO., LTD. http://www.estech.co.kr Ch No.Freq (MHz)Power Output (dBm) 1931.2542.96 1960.0043.01 1988.7542.80 Report Number : ESTR0803-0277 of 29 ͅΟ͑΁ΦΥ΀ΦΥ͑ΡΦΥ ͅΟ͑΁ΦΥ΀ΦΥ͑ΡΦΥ ͨ͞͡ ͨͩͥͨ͟͞͡ ͣͤͣ͟͡ ͧͦ͞ ͧͦ͢͢͟͢͡͞ ͣͦͥͥ͟ ͧ͞͡ ͧͦͣͧ͢͟͞͡ ͤͧͩ͟͡ ͦͦ͞ ͣͣͧͦͦ͟͡͞ ͤͨͥͥ͟ ͦ͞͡ ͣͩͥͥͦ͟͞͡ ͥͣͧͩ͟ ͥͪ͞ ͣͩͥͥͪ͟͢͞ ͥͤͥ͟͡ ͥͩ͞ ͣͩͤͪͥͩ͟͞ ͥͣͩͩ͟ ͥͨ͞ ͣͩͤͦͥͨ͟͞ ͥͣͪͥ͟ Report Number : ESTR0803-0277 of 29 FCC ID : STESN-NOTCH-43-C 4.4 Test Plot Uplink RF Power Output (25) RF Power Output (600) ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0803-0278 of 29 RF Power Output (1175) Report Number : ESTR0803-0278 of 29 FCC ID : STESN-NOTCH-43-C Downlink RF Power Output (25) RF Power Output (600) ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0803-0279 of 29 RF Power Output (1175) Report Number : ESTR0803-0279 of 29 FCC ID : STESN-NOTCH-43-C Input Signal Output Power Uplink (600) ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0803-02710 of 29 Downlink (600) Report Number : ESTR0803-02710 of 29 FCC ID : STESN-NOTCH-43-C 5. Occupied Bandwidth 5.1 Test Procedure 5.2 Test Equipments The following test equipments are used during tests 5.3 Test Results ͑͑ ESTECH CO., LTD. http://www.estech.co.kr Signal Generator EquipmentModel E4407B E4432B The transmitter output is connected to the spectrum analyzer. The RBW is set to 1% of the Emission bandwidth. The VBW is set to 3 times the RBW. The sweep time is coupled. Manufacturer Spectrum AnalyzerAgilent HP Report Number : ESTR0803-02711 of 29 (Uplink) (Downlink) 11751908.751.39 6001880.001.38 251851.251.37 26dB Bandwidth(MHz)ChannelFrequency(MHz) ChannelFrequency(MHz)26dB Bandwidth(MHz) 251931.251.35 6001960.001.37 11751988.751.39 Report Number : ESTR0803-02711 of 29 FCC ID : STESN-NOTCH-43-C 5.4 Test Plot Uplink 26dB Channel Bandwidith(25) 26dB Channel Bandwidith(600) ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0803-02712 of 29 26dB …

Text truncated - open the document above for the full version.