STESNIDEN30iDen Mini Wireless Repeater

iDEN MINI (RSN-iDEN-30) User’s Manual GG G G R-tron Inc. User’s Manual -2- G RF EXPOSURE INFORMATION The antenna used for this transmitter must not exceed 7dBi and must be installed to provide a minimum separation distance of 22cm from all persons. CAUTION This equipment is indoor use and all the communication wirin g are limited to inside of the building. iDEN MINI G User’s Manual -3- G This document describes the specifications, installation and operation of iDEN MINI. Hardware and software mentioned in this document are subject to continuous development and improvement. Consequently, there may be minor discrepancies between the information in the document and the performance and design of the product. Specifications, dimensions and other statements mentioned in this document are subject to change without notice. R-tron Inc. 6402 College Boulevard Overland Park, KS 66211 Phone: +1-913-344-9977, 1-888-31R-TRON Fax: +1-913-344-9988 Internet: www.r-tron.com R-tron is registered trademarks of R-tron Inc. Other products and company names mentioned herein this manual might be trade marks or trade names of their respective owners. This document or parts of it may not be reproduced without the written permission of R-tron Inc. Infringements will be prosecuted. All rights reserved Copyright © R-tron Inc. 2000-2007 iDEN MINI G User’s Manual -4- G Contents Abbreviations .................................................................................................................... 6G 1.GIntroduction ........................................................................................................ 7G 2.GDescription .......................................................................................................... 9G 2.1GSystem Specifications ................................................................................................. 9G 2.1.1.GElectrical Specifications .................................................................................... 9G 2.1.2.GMechanical Specifications .............................................................................. 10G 2.2GSub Unit Overview ..................................................................................................... 11G G 2.2.1.GUDC Module ................................................................................................... 13G 2.2.2.GMultiplexer ...................................................................................................... 14G 2.2.3.GMCU (Main Control Unit) ................................................................................ 15G 2.2.4.GPower Supply ................................................................................................. 16G 2.2.5.GHPAs (High Power Amplifiers) ........................................................................ 17G 3.GHardware Installation .......................................................................................... 18G 3.1GCheck List of Items .................................................................................................... 18G 3.2GMounting .................................................................................................................... 19G 3.3GGrounding .................................................................................................................. 20G 3.4GRF Cable Connection ................................................................................................ 20G 3.5GPower Up ................................................................................................................... 21G 4.GCommand and Control through the Hyper Terminal ................................................22G 4.1 Setting for Command and Control through the Hyper Terminal ..................................... 22G 4.2 Command and Control through the Hyper Terminal ...................................................... 26G 4.3 Downloading of the latest firmware ................................................................................ 32G 5.GTroubleshooting .................................................................................................. 37G 5.1GRF Connection Check ............................................................................................... 37G 5.2GPower Connection ..................................................................................................... 37G 5.3GRed Light on the Alarm LED ...................................................................................... 38G 6.GGlossary .............................................................................................................40G 6.1GALC (Automatic Level Control) .................................................................................. 40G 6.2GASD (Automatic Shutdown) ....................................................................................... 40G iDEN MINI G User’s Manual -5- G Figures Figure 1.GR-tron iDEN MINI .................................................................................................... 7G Figure 2.GOverview: Service .................................................................................................... 8G Figure 3.GDimension of iDEN MINI ........................................................................................ 10G Figure 4.GInternal View of iDEN MINI .................................................................................... 11G Figure 5.GBlock Diagram ....................................................................................................... 12G Figure 6.GUDC Module .......................................................................................................... 13G Figure 7.GMultiplexer ............................................................................................................ 14G Figure 8.GMain Control Unit ...............................................................................................…

Text truncated - open the document above for the full version.

iDEN MINI User’s Manual -15- 2.2.4. MCU (Main Control Unit) MCU is the control unit of iDEN MINI. It controls and monitors operational parameters. It also generates alarms, an event log and many other functions of the iDEN MINI. Figure 8. Main Control Unit Pin Map Port Connected to J1 MCU Vcc(+12V) J3 USB Port(Manufacturer use only) J4 PSU Alarms J5 Door Alarm J6 Status LEDs J7 iDEN 800 PLL,B/S,OUT DET J8 iDEN 900 PLL,B/S,OUT DET J9 Tx HPA J10 Rx HPA J11 RJ-45 port iDEN MINI User’s Manual -16- 2.2.5. Power Supply The Power Supply Unit (PSU) supplies a steady DC power to iDEN MINI by drawing power from the general in-wall AC outlets. Figure 9. Power Supply Specifications Item Specifications Environmental Operating Temp -10°C~50°C/14°F~122°F Humidity 20%~90%RH Cooling method Natural air Voltage AC110~125V Current 6A Max / 6V, 12V, 27VDC Frequency 50~60Hz typ Leakage Current 0.5mA max.@110V AC iDEN MINI User’s Manual -17- 2.2.6. HPAs (High Power Amplifiers) The High Power Amplifiers (HPAs) amplifies the transmitted signal from a base station at the final stage of the repeater and vice versa. Figure 10. HPAs(High Power Amplifiers) iDEN MINI User’s Manual -18- 3. Hardware Installation The installation procedure is as follows: „ Check List of Items „ Mounting „ Grounding „ RF Connection „ Power up 3.1 Check List of Items Index Items Q’ty 1 iDEN MINI 1 2 Power Cord 1 3 Screws for Mounting 4 4 Template for marking of the pilot holes 1 Items A-TYPEA-TYPE A-TYPEA-TYPE B-TYPEB-TYPE B-TYPEB-TYPE Use this template to mark the location for pilot holes Figure 11. Items 1 2 3 4 iDEN MINI User’s Manual -19- 3.2 Mounting iDEN MINI is easy to mount using the assembled mounting bracket, which has Ø9 holes for the provided 5/16" fixing screws. Figure 12. Mounting Step 1. Remove the cover of double-coated foam tape squares at each corner on the back side of the template. Step 2. Stick the provided template to the wall using the tape squares while adjusting the horizon. Step 3. Mark with a pen for the holes and drill the marks or drill holes directly on the mark in the template. Step 4. Put the screws or bolts into the holes. Step 5. Mount the iDEN MINI on the right position. CAUTION Firmly affix the equipment on the wall of a building and Check necessary. iDEN MINI User’s Manual -20- 3.3 Grounding A rod on the left side is intended for a building ground. Connect the ground cable to the rod. Figure 13. Grounding 3.4 RF Cable Connection a. Connect a cable from a donor antenna to the DONOR ANTENNA Port. b. Connect a cable from the SERVICE ANTENNA Port to a repeater’s service antenna. WARNING Dangerously high voltages may occur and damage the equipment if the e quipment is not groundedproperly. iDEN MINI User’s Manual -21- Mobile Station DonorService Figure 14. Configuration: RF Cable Connection 3.5 Power Up a. Connect the power cord. b. Plug the power cord into a wall outlet. c. Check if the green LED at the bottom turns on. Figure 15. Power Cord Connection iDEN MINI User’s Manual -22- 4. Command and Control through the Hyper Terminal 4.1 Setting for Command and Control through the Hyper Terminal Figure 16. Local connection to the iDEN MINI * iDEN MINI operates on a customer provided PC based platform with the following system requirements. Windows® 2000 or Windows® XP 128 MB RAM or more Pentium processor or more keyboard RJ-45 jack Step 1 Open My Network Places. iDEN MINI User’s Manual -23- Step 2 Click the “View network connections”. Step 3 Push the right button of mouse and select the properties. iDEN MINI User’s Manual -24- Step 4 Click the properties of TCP/IP. Step 5 Set the values and OK as the following. Close all windows. iDEN MINI User’s Manual -25- Step 6 Execute the Hyper Terminal. Step 7 Name the session and OK. Step 8 Select the TCP/IP (Winsock). iDEN MINI User’s Manual -26- Step 9 Set the values as the following and OK. 4.2 Command and Control through the Hyper Terminal Step 1. To see the current status, hit “Enter” key only.

iDEN MINI User’s Manual -27- Step 2. Type “HELP” in and hit “Enter” key to look up the list of commands. Step 3. To execute a command, “Enter” key must be hit. If the command is successful, “OK” is displayed but if not, “ERROR” is displayed. To reset a MCU (Main Control Unit), type “RESET” in. Examples 1 Frequency Setup 1.1 iDEN 800, 1.1.1 If the bandwidth is 18MHz, 1.1.1.1 If the frequency range is 851.0MHz ~ 869.0MHz, 1.1.1.2 If the frequency range is 850.8MHz ~ 868.8MHz (200KHz shift), 1.1.1.3 If the frequency range is 850.6MHz ~ 868.6MHz (400KHz shift), >>8B 0↵ Command: >>RESET↵ >>8F 0↵ >>8F 1↵ >>8F 2↵ iDEN MINI User’s Manual -28- 1.1.2 Otherwise, the bandwidth is 7MHz 1.1.2.1 If the frequency range is 862.0MHz ~ 869.0MHz, 1.1.2.2 If the frequency range is 861.8MHz ~ 868.8MHz (200KHz shift), 1.1.2.3 If the frequency range is 861.6MHz ~ 868.6MHz (400KHz shift), 1.2 iDEN 900 (5MHz fixed bandwidthBandwidthsetup is not necessary), 1.2.1 If the frequency range is 935.0MHz ~ 940.0MHz, 1.2.2 If the frequency range is 934.8MHz ~ 939.8MHz (200KHz shift), 1.2.3 If the frequency range is 934.6MHz ~ 939.6MHz (400KHz shift), 2 Gain Setup 2.1 iDEN 800 9 TX Gain: 80dB, RX Gain 80dB 2.2 iDEN 900 9 TX Gain: 80dB, RX Gain 80dB * Please, turn off the ALC and ASD by the commands “TXALC OFF”, “RXALC OFF”, and “ASD OFF” before the gain setup. Factory defaults are specified in ALC ON and ASD ON. While the ALC and ASD are on, the gain setup is not available and an Error may be occurred. >>8TG 80↵ >>8RG 80↵ >>9TG 80↵ >>9RG 80↵ >>8B 1↵ >>8F 0↵ >>8F 1↵ >>8F 2↵ >>9F 0↵ >>9F 1↵ >>9F 2↵ iDEN MINI User’s Manual -29- 3 ALC (Automatic Level Control) Level Setup: 30dBm * ALC (Automatic Level Control) maintains the specific TX and RX output power by the setup parameter. Do not set the ALC value over 30. 4 ASD* (Automatic Shut Down) Setup: 9 Level: 33dBm, Time: 3sec, Count: 10 5 Tx HPA On 6 Rx HPA On <Specifying of the operating frequencies, bandwidth, and gains> >>RHPA ON↵ >>TXALC_LEVEL 30↵ >>TXALC ON↵ >>RXALC_LEVEL 30↵ >>RXALC ON↵ >>ASD_LEVEL 33↵ >>ASD_TIME 3↵ >>ASD_COUNT 10↵ >>ASD ON↵ * If the output power gets higher than “ASD_LEVEL”, the repeater will shut down for “ASD_TIME” time and then turn on the amp and measure the output power again. If this repeats “ASD_COUNT” times, the repeater will shut down completely. >>THPA ON↵ iDEN MINI User’s Manual -30- <Specifying of the ALCs> <Setting of the ASD parameters> iDEN MINI User’s Manual -31- <The screenshot of the example setting> <The screenshot of the ALC Operating> The maximum output power for operating is +30 dBm on both Tx and Rx. iDEN MINI User’s Manual -32- 4.3 Downloading of the latest firmware Step 1. Click the “Send File...” of Transfer menu. Step 2. Browse the latest firmware file. iDEN MINI User’s Manual -33- Step 3. Select file to send. Step 4. Send the file on the “Xmodem” protocol. iDEN MINI User’s Manual -34- Step 5. Push the “Send” button. <The screenshot of the Xmodem file send> iDEN MINI User’s Manual -35- <The screenshot of firmware download completed> Step 6. Type “VER” and hit the “Enter” key to check the version of firmware. iDEN MINI User’s Manual -36- * Reference The Operating Bandwidth & Frequencies BandwidthOperating Frequency iDEN 800 18MHz-bandwidth Downlink 851~869MHz 850.8~868.8MHz 850.6~868.6MHz Uplink 806~824MHz 805.8~823.8MHz 805.6~823.6MHz 7MHz-bandwidth Downlink 862~869MHz 861.8~868.8MHz 861.6~868.6MHz Uplink 817~824MHz 816.8~823.8MHz 816.6~823.6MHz iDEN 900 5MHz-bandwidth Downlink 935~940MHz 934.8~939.8MHz 934.6~939.6MHz Uplink 896~901MHz 895.8~900.8MHz 895.6~900.6MHz Operating bandwidth and Frequencies of iDEN iDEN MINI User’s Manual -37- 5. Troubleshooting 5.1 RF Connection Check Problem Either the downlink output power or the uplink output power (=Input Power to the repeater) is too weak. Solution Check if the following RF connections are loose: 1. The cable connection from the donor antenna to the donor antenna port 2. The cable connection from the service antenna port to the service antenna 5.2 Power Connection Problem All LEDs at the bottom are turned off. Figure 17. LEDs Off Solution Check if the power cord is connected correctly and the green LED at the bottom is on. iDEN MINI User’s Manual -38- Figure 18. AC power cord Check 5.3 Red Light on the Alarm LED Problem Red light LED turns on the Alarm LED after applying AC power. Figure 19. Red Light on Alarm LED iDEN MINI User’s Manual -39- * Check points The red LED can be turned on due to out of range as the following below: Alarms Lower Upper Tx Input -70dBm -30dBm Tx/Rx Output 0dBm 35dBm Temperature -10C 80C DC Voltage 20V 30V DC Current 0A 5A Solution If the red light LED is steady in the range of critical values, request a technical support. iDEN MINI User’s Manual -40- 6. Glossary 6.1 ALC (Automatic Level Control) * ALC feature prevents the repeater from exceeding its maximum output power, by reducing the gain automatically. ALC is used to adjust the gain to an appropriate level for a range of input signal levels. [Example] [For the repeater with 30dBm Maximum Output power, 80dB Maximum Gain /30dB Gain control range, -> If input signal is -30Bm and ALC is set as 30dBm, the gain will be 60dB to adjust to the level. If input signal is -55dBm, the output power will be 25dBm by the limitation of the maximum gain even though the ALC is set as 30dBm.] 6.2 ASD (Automatic Shutdown) * Automatic shut down protects the repeater itself from the oscillation or excessive input signal and eliminates any degradation to the network. There are three parameters, ASD_LEVEL, ASD_TIME and ASD_COUNT. If the output power gets higher than “ASD_LEVEL”, the repeater will shut down for “ASD_TIME” time and then turn the amp back on and measure the output power again. If this repeats “ASD_COUNT” times, the repeater will shut down completely. [Example] [For the repeater with 30dBm Maximum Output power, 80dB Maximum Gain /30dB Gain control range, Assuming ASD_ LEVEL: 35dBm, ASD_TIME: 3sec, ASD_COUNT: 3…

Text truncated - open the document above for the full version.

Jisan IT Venture Center 2,3F, 1004-9,10, Doksan-Dong, Gumcheon-Gu, Seoul, Korea Tel: +82-2-896-4101 Fax: +82-2-896-4107 [email protected] May 7. 2007 Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 In re: R-tron, Inc. FCC ID: STESNiDEN30 Wireless Repeater Part 90 Certification Request for Confidentiality To whom it may concern: We the undersigned R-tron,Inc. here by authorize ESTECH Co.,Ltd.(EST) of Korea to act on our behalf in all matters relating to all processes required in the FCC Part 90 approval and any communication needed with the national authority. Any and all acts carried out by EST on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely, yours Sincerely, Jong Hwa, Park/R&D Center Director R&D Center R-tron, Inc.

Jisan IT Venture Center 2,3F, 1004-9,10, Doksan-Dong, Gumcheon-Gu, Seoul, Korea Tel: +82-2-896-4101 Fax: +82-2-896-4107 [email protected] May 7. 2007 Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 In re: R-tron, Inc. FCC ID: STESN IDEN30 Wireless Repeater Part 90 Certification Request for Confidentiality Gentlemen: In accordance with 0.459 of CFR 47, R-tron Inc. hereby requests confidentiality of the Block Diagram, Circuit Diagrams, Repeater Description, Technical Specification, Parts List and Tune-Up Procedure for the above-referenced certification application. These documents contain detailed system and equipment description and related information about the product which R-tron Inc. Considers to be proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, R-tron Inc. considers this information to be of benefit to its competitors, such that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, Jong Hwa, Park/R&D Center Director R&D Center R-tron, Inc.

RSN-iDEN-30 EUT-Photograph *Repeater* <Front View > < Rear View > <Top view> <Bottom view>

ma y n ot h armf ul in terference. RSN-iDEN-30 COMPLIES W ITH PART 90, FCC RULES. 110 -125V ~ , 60Hz , 4A :PRODUCT PART NUMBER POWER : FCC REG. NO. : STESNiDEN30 SERIAL NO. / DATE : E25 810 9 31CY I.T.E :MAKER MADE IN KOREA R-tron lnc. Operation is su bject to th e cond ition that this device Th is d ev ice co mpl ies with Part 1 5 of the FCC Rules. BRACKET LAN ALARM AC IN 110 -125V ~ 800MHz TX MON. 900MHz RX MON. DONOR ANTENNA SERVICE ANTENNA 900MHz TX MON. 800MHz RX MON.

<Left side view> <Right side view> < The Inside of the Repeater > *RF-Module* <RSN-iDEN-30 UDC Top view> <RSN-iDEN-30 800 UDC> <RSN-iDEN-30 900 UDC> <RSN-iDEN-30 HPA Top View> <RSN-iDEN-30 HPA> *MCU Board* *Communication & LED Board* <Front side> <Rear side>

S PG π4 S PG π4

Product Name Model Name Applicant FCC ID ESTECH CO., LTD Rm. 1015 World Venture Center, 426-5 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea. Tel:82-2-867-3201, Fax:82-2-867-3204 STESNIDEN30 RSN-iDEN-30 R-tron Inc. ͑͑ESTECH CO., LTD. http://www.estech.co.kr FCC TEST REPORT Wireless Repeater Report Number : ESTR0705-0021 of 30 FCC ID : STESNIDEN30 Company Name Address Product Name Model No.Manufacturer Serial No. Country of origin Issued DateTested Date ͑͑ESTECH CO., LTD. http://www.estech.co.kr Rm. 1015 World Venture Center, 426-5 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea. Tel:82-2-867-3201, Fax:82-2-867-3204 ESTECH CO., LTD FCC Test Report Applicant Product Report Number RSN-iDEN-30 KOREA R-tron Inc. o This is certified that the above mentioned products have been tested for the sample provided by client. o No part of this document may not be duplicated or reproduced by any means without the express written permission of Estech Co., Ltd. Standard FCC PART 90 Subpart I Tested by Approved by S.R. Kim/ Engineer (Signature) Jay Kim/ Engineering Manager (Signature) Test Result Pass 2007-05-03 2007-04-02 ~ 2007-5-03 Other ESTR0705-002 Jisan IT Venture Center 3F, 1004-9 Doksna-Dong, Gumcheon- Gu, Seoul, Korea Wireless Repeater NONE R-tron Inc. Report Number : ESTR0705-0022 of 30 FCC ID : STESNIDEN30 1. General Information Page 4 2. Laboratory Information Page 5 3. Summary of Test Results Page 5 4. RF Output Power Page 6 5. Occupied Bandwidth Page 12 6. Spurious and Harmonic Emission at Antenna Terminal Page 18 7. Field Strength of Spurious Radiation Page 22 8. Frequency stability Page 24 Contents ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0705-0023 of 30 FCC ID : STESNIDEN30 1. General Information 1.1 EUT Description Frequency Rx :850.6MHz - 869MHz, 934.6MHz - 940MHz AC110V Power Rating ͑͑ ESTECH CO., LTD. http://www.estech.co.kr FCC ID STESNIDEN30 Modulation Type Product Name Model Name Wireless Repeater RSN-iDEN-30 Tx :806MHz – 824MHz, 896MHz – 901MHz iDen(QAM) Report Number : ESTR0705-0024 of 30 FCC ID : STESNIDEN30 2. Laboratory Information 3. Summary of Test Results Result PASS PASS PASS PASS ͑͑ ESTECH CO., LTD. http://www.estech.co.kr 58-1, Osan-Ri, GaNam-Myon, YeoJoo-Gun, KyungKi-Do, Korea 97-1, Hoiuk-Ri Majang-Myon, Icheon-city, KyungKi-Do, Korea 2.4 Major Accredited Mark Test Item Accredited by KOLAS(ISO/IEC 17025) Head Office EMC Lab(Ichon) EMC Lab(Yanggi) Standard RF Output Power Occupied Bandwidth PASS 2.1 Laboratory Name 2.2 Location 2.3 Quality System Estech Co., Ltd. Rm. 1015, World Venture Center II, 426-5 Gasan-dong Geumcheon-gu, Seoul, 153-803. Korea. Part 90 Field Strength of Spurious Radiation Frequency stability Spurious and Harmonic Emission at Antenna Terminal Report Number : ESTR0705-0025 of 30 FCC ID : STESNIDEN30 4. RF Output Power 4.1 Test Procedure 4.2 Test Equipments The following test equipments are used during tests Cal. Due Date 2008-03-02 2008-03-02 2008-03-02 4.3.1 Test Results (800MHz Uplink) 29.8930.00 30.19 30.01 30.00 30.00 8498A Measured Output power(dBm)Rated Output power(dBm) The EUT was placed on a wooden turn table 3 meters from the receive antenna. The receive antenna height and turn table rotation was adjusted for the highest reading on the receive spectrum analyzer. For CDMA signals, a peak detector is used, with RBW = VBW = 3MHz. For AMPS, GSM, and NADC TDMA signals, a peak detector is used, with RBW = VBW = 1MHz, A Horn antenna was substituted in place of the EUT. This Horn antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For reading 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. Model E4407B HP HP Manufacturer Agilent E4432B 824.00 815.00 806.00 Freq (MHz) ͑͑ESTECH CO., LTD. http://www.estech.co.kr Signal Generator Attenuator Equipment Spectrum Analyzer Report Number : ESTR0705-0026 of 30 FCC ID : STESNIDEN30 4.3.2 Test Results (800MHz Downlink) 4.3.3 Test Results (900MHz Uplink) 4.3.4 Test Results (900MHz Downlink) 940.0029.4430.00 935.00 938.0029.5930.00 29.8230.00 901.0029.6630.00 Freq (MHz)Measured Output power(dBm)Rated Output power(dBm) Freq (MHz)Measured Output power(dBm)Rated Output power(dBm) 899.0030.4030.00 ͑͑ ESTECH CO., LTD. http://www.estech.co.kr 896.0030.0029.71 Freq (MHz)Measured Output power(dBm)Rated Output power(dBm) 851.0029.8230.00 860.0029.5730.00 869.0029.8530.00 Report Number : ESTR0705-0027 of 30 FCC ID : STESNIDEN30 4.4 Test Plot Input power (800MHz Uplink) 815MHz Output power (800MHz Uplink) 815MHz ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0705-0028 of 30 FCC ID : STESNIDEN30 Input power (800MHz Downlink) 860MHz Output power (800MHz Downlink) 860MHz ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0705-0029 of 30 FCC ID : STESNIDEN30 Input power (900MHz Uplink) 899MHz Output power (800MHz Uplink) 899MHz ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0705-0021 of 1 FCC ID : STESNIDEN30 Input power (900MHz Downlink) 938MHz Output power (800MHz Downlink) 938MHz ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0705-00211 of 30 FCC ID : STESNIDEN30 5. Occupied Bandwidth 5.1 Test Procedure 5.2 Test Equipments The following test equipments are used during tests Cal. Due Date 2008-03-02 2008-03-02 2008-03-02 5.3 Test Results (800MHz&900MHz Uplink) 824.0015.463 8498A 815.0015.537 806.0015.588 HP 26dB Bandwidth(kHz) Attenuator ͑͑ ESTECH CO., LTD. http://www.estech.co.kr Signal Generator EquipmentModel HPE4432B Spectrum Analyzer Frequency(MHz) Unless specified elsewhere, channel spacings and bandwidths that will be authorized in the following frequency bands are given in the following Table. Standard Channel Spacing/Bandwidth Frequency Band Channel Spacing Authorized Bandwidth (MHz) (kHz) (…

Text truncated - open the document above for the full version.

Product Name Model Name Applicant FCC ID ESTECH CO., LTD Rm. 1015 World Venture Center, 426-5 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea. Tel:82-2-867-3201, Fax:82-2-867-3204 STESNIDEN30 RSN-iDEN-30 R-tron Inc. ͑͑ESTECH CO., LTD. http://www.estech.co.kr FCC TEST REPORT Wireless Repeater Report Number : ESTR0705-0021 of 30 FCC ID : STESNIDEN30 Company Name Address Product Name Model No.Manufacturer Serial No. Country of origin Issued DateTested Date ͑͑ESTECH CO., LTD. http://www.estech.co.kr Rm. 1015 World Venture Center, 426-5 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea. Tel:82-2-867-3201, Fax:82-2-867-3204 ESTECH CO., LTD FCC Test Report Applicant Product Report Number RSN-iDEN-30 KOREA R-tron Inc. o This is certified that the above mentioned products have been tested for the sample provided by client. o No part of this document may not be duplicated or reproduced by any means without the express written permission of Estech Co., Ltd. Standard FCC PART 90 Subpart I Tested by Approved by S.R. Kim/ Engineer (Signature) Jay Kim/ Engineering Manager (Signature) Test Result Pass 2007-05-03 2007-04-02 ~ 2007-5-03 Other ESTR0705-002 Jisan IT Venture Center 3F, 1004-9 Doksna-Dong, Gumcheon- Gu, Seoul, Korea Wireless Repeater NONE R-tron Inc. Report Number : ESTR0705-0022 of 30 FCC ID : STESNIDEN30 1. General Information Page 4 2. Laboratory Information Page 5 3. Summary of Test Results Page 5 4. RF Output Power Page 6 5. Occupied Bandwidth Page 12 6. Spurious and Harmonic Emission at Antenna Terminal Page 18 7. Field Strength of Spurious Radiation Page 22 8. Frequency stability Page 24 Contents ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0705-0023 of 30 FCC ID : STESNIDEN30 1. General Information 1.1 EUT Description Frequency Rx :850.6MHz - 869MHz, 934.6MHz - 940MHz AC110V Power Rating ͑͑ ESTECH CO., LTD. http://www.estech.co.kr FCC ID STESNIDEN30 Modulation Type Product Name Model Name Wireless Repeater RSN-iDEN-30 Tx :806MHz – 824MHz, 896MHz – 901MHz iDen(QAM) Report Number : ESTR0705-0024 of 30 FCC ID : STESNIDEN30 2. Laboratory Information 3. Summary of Test Results Result PASS PASS PASS PASS ͑͑ ESTECH CO., LTD. http://www.estech.co.kr 58-1, Osan-Ri, GaNam-Myon, YeoJoo-Gun, KyungKi-Do, Korea 97-1, Hoiuk-Ri Majang-Myon, Icheon-city, KyungKi-Do, Korea 2.4 Major Accredited Mark Test Item Accredited by KOLAS(ISO/IEC 17025) Head Office EMC Lab(Ichon) EMC Lab(Yanggi) Standard RF Output Power Occupied Bandwidth PASS 2.1 Laboratory Name 2.2 Location 2.3 Quality System Estech Co., Ltd. Rm. 1015, World Venture Center II, 426-5 Gasan-dong Geumcheon-gu, Seoul, 153-803. Korea. Part 90 Field Strength of Spurious Radiation Frequency stability Spurious and Harmonic Emission at Antenna Terminal Report Number : ESTR0705-0025 of 30 FCC ID : STESNIDEN30 4. RF Output Power 4.1 Test Procedure 4.2 Test Equipments The following test equipments are used during tests Cal. Due Date 2008-03-02 2008-03-02 2008-03-02 4.3.1 Test Results (800MHz Uplink) 29.8930.00 30.19 30.01 30.00 30.00 8498A Measured Output power(dBm)Rated Output power(dBm) The EUT was placed on a wooden turn table 3 meters from the receive antenna. The receive antenna height and turn table rotation was adjusted for the highest reading on the receive spectrum analyzer. For CDMA signals, a peak detector is used, with RBW = VBW = 3MHz. For AMPS, GSM, and NADC TDMA signals, a peak detector is used, with RBW = VBW = 1MHz, A Horn antenna was substituted in place of the EUT. This Horn antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For reading 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. Model E4407B HP HP Manufacturer Agilent E4432B 824.00 815.00 806.00 Freq (MHz) ͑͑ESTECH CO., LTD. http://www.estech.co.kr Signal Generator Attenuator Equipment Spectrum Analyzer Report Number : ESTR0705-0026 of 30 FCC ID : STESNIDEN30 4.3.2 Test Results (800MHz Downlink) 4.3.3 Test Results (900MHz Uplink) 4.3.4 Test Results (900MHz Downlink) 940.0029.4430.00 935.00 938.0029.5930.00 29.8230.00 901.0029.6630.00 Freq (MHz)Measured Output power(dBm)Rated Output power(dBm) Freq (MHz)Measured Output power(dBm)Rated Output power(dBm) 899.0030.4030.00 ͑͑ ESTECH CO., LTD. http://www.estech.co.kr 896.0030.0029.71 Freq (MHz)Measured Output power(dBm)Rated Output power(dBm) 851.0029.8230.00 860.0029.5730.00 869.0029.8530.00 Report Number : ESTR0705-0027 of 30 FCC ID : STESNIDEN30 4.4 Test Plot Input power (800MHz Uplink) 815MHz Output power (800MHz Uplink) 815MHz ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0705-0028 of 30 FCC ID : STESNIDEN30 Input power (800MHz Downlink) 860MHz Output power (800MHz Downlink) 860MHz ͑͑ESTECH CO., LTD. http://www.estech.co.kr Report Number : ESTR0705-0029 of 30 FCC ID : STESNIDEN30 Input power (900MHz Uplink) 899MHz O…

Text truncated - open the document above for the full version.