SZO-RR21UHF RFID Reader for sports time keeping

race result AG Model: RR21 Quick Reference Guide Setup Guidelines The following guidelines describe the correct setup of your Ubidium Ground Antenna to ensure maximum performance and prevent damage to the components. Additionally, you should be aware of the setup precautions to further optimise the performance of the system. Unfolding the Ground Antenna You should start unfolding the antenna from the side on which you will position the Ubidium System. Stand the antenna vertically with the Connector Cable on the ground, at the edge of your Timing Point next to your Ubidium System. Depending on the length of your antenna you may find it easier to slightly separate the segments to allow them to stand freely. Pull the last antenna segment to unfold the antenna across the width of your Timing Point. Folding the Ground Antenna Again start at the end of the antenna which is closest to your Ubidium System and ensure the Connector Cable is disconnected from your system. Starting from the second antenna segment pull the segments towards you to fold the antenna in to an accordion at the hinges. It is usually easier to keep the segments standing whilst you fold the additional length of the antenna. Take care not to lift the segment vertically as this may separate the cover from the base making it harder to fold. Once all the segments have been folded you can push all of them together to flatten the hinges, and we recommend using the provided strap to secure the segments together. We recommend folding and storing your Ubidium Ground Antenna with the red covers facing outwards to prevent causing deforming the edges of the covers. race result AG Setup Precautions Antenna Length Your Ground Antenna should cover the entire width of your Timing Point to ensure that all participants cross directly over the antennas, it should not be possible for participants to go around the antenna in any way. If your Timing Point is wider than the available Ground Antenna then you may need to consider setting up barriers to funnel participants across the antenna. If your Ubidium Ground Antenna is longer than the width of the Timing Point you should split the antenna to remove the unused segments. This will further optimise the performance of the detections since the unused Antenna Elements will not be in operation. Never fold additional segments vertically to point back across the mat, since multiple elements are activated simultaneously this can cause the detection fields to overlap which may inhibit the performance of the system. Additional segments should be removed when possible, or can be setup as normal, even laid under other structures, without a negative impact on read rates. When using Ground Antennas with more than 10 elements where passings in excess of 10,000 participants are expected or those setup on ground with a low friction coefficient, it is recommended to additionally secure the Ground Antenna using a heavy-duty tape on the leading edge. Using Multiple Systems in Close Proximity If using multiple systems in the same location, for example using a main and backup timing system at the same Timing Point, then you should ensure a minimum of 5 m / 16 ft between the antennas. If the detection fields of two separate systems overlap then it can inhibit the performance of both systems. Protection from External Factors Particularly in busy areas such as the finish you should try to protect your Ground Antenna from unwanted intrusion such as spectators or event staff. race result AG People who are unaware surroundings may stand on sensitive components such as the Ubidium System or the Connector Cable which could cause damage to the system or completely break components. Standing on an Antenna Segment may also cause high reflections on an Antenna Element which will prevent that element from working which may impact your detection performance. It is also possible that other participants who are standing nearby may cause unwanted detections. Whilst this is normally ignored at a software level it is good practice to try and avoid unwanted detections. We recommend creating a 1 m / 4 ft buffer around the Ubidium System and Ground Antenna. Connecting to the System A single connector is used to connect the Ubidium Ground Antenna to the Expansion Port of the Ubidium System. It is recommended to only connect or disconnect the Ground Antenna when the Ubidium System is powered off. To connect the Ground Antenna to the Ubidium System, first open the rubber port cover from the Expansion Port and align the red marker on the outer sleeve of the connector with the red marker on the Expansion Port. This will also align the guide pins on the metal sleeve of the connector. Firmly push the connector in until it clicks in to place, if the connector is correctly inserted it should not be loose inside the Expansion Port. To remove the Ground Antenna Connector from the system pull on the ridged section of the outer metal sleeve which will release the catch, allowing you to completely remove the connector. You should always push and pull the connector straight in or out, and at no point should you attempt to twist the connector inside the Expansion Port as this may damage the internal pins. race result AG Components The Ubidium Ground Antenna is comprised of five key components. • Black Plastic Base • Red Plastic Cover • Ubidium Antenna Element • Ubidium Connector Cable • Ubidium Interconnecting Cables Each component has been carefully designed for maximum performance when used as part of the Ubidium Ground Antenna. Black Plastic Base The black plastic base sits on the ground and has cutouts to hold the Ubidium Antenna Elements and cables. It is then covered by the red plastic cover which slots in to place on the side and is secured using the Snap-In Buttons. race result AG The design of the base element is assymetric, one end will additionally be marked as a splitting point and will have a different layout of the internal cable channels. …

Text truncated - open the document above for the full version.

To: Federal Communications Commission Date: 2025-AUG-04 7435 Oakland Mills Road Columbia, MD 21046 USA Attestation Certification designating a U.S. Agent for Service of Process Section 2.911(d)(7) (KDB 986446 D01 Covered Equipment) Race result AG (“the applicant”) as required by section 2.911(d)(7), designate below contact located in the United States for purposes of acting as the applicant’s agent for service of process. The applicant also accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The US Agent confirms by the signature, that he has accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant as noted below. Type of Equipment subject to FCC Certification: UHF RFID Reader FCC ID: SZO-RR21 Sincerely yours, Applicant/Grantee US Agent for Service of Process FRN: 0024039364 FRN: 0033425919 _________________ _________________ Race result AG RACE RESULT Americas Inc Nikias Klohr Mark Bockmann CTO & Head of R&D CEO RACE RESULT Americas E-Mail: [email protected] [email protected] 609 S Taylor Ave Unit E CO 80027 Louisville, USA

The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 1 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential Address: CSA Group Bayern GmbH Straubinger Straße 100 94447 Plattling GERMANY Phone +49(0)9931-98360 E - mail [email protected] Internet: http://www.csagroup.org Test – Results Order-No.: 80240901-00 Rev_0 Client race result AG, Joseph-von-Fraunhofer-Str. 11, 76327 Pfinztal, GERMANY Manufacturer race result AG, Joseph-von-Fraunhofer-Str. 11, 76327 Pfinztal, GERMANY Product Description PCB antenna Type / Model Name RR21 Testing commenced on 2025-02-11 Pretest is made according to Customer specific Testing concluded on 2025-02-11 Serial - No. N/A Remarks: Customer specific tests in order to determine antenna gain and antenna performance. This test result consists of 23 page(s). The test result only corresponds to the tested sample. It is not permitted to copy extracts of these test results without the written permission of the test laboratory. Date Checked by Tested by Result 2025-03-24 Not applicable, no standards used The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 2 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential Photo documentation and setup description Measurements are performed with a 3-meter test setup in fully anechoic chamber FAR1. The verified measurement system 09-16/30-25-001 for EIRP measurements is used. Height of EUT: 1.5 m Height of receiving antenna: 1.5 m Test distance: 3.0 m Polarisation of receiving antenna horizontal, vertical Measured frequencies: 865 MHz, 868 MHz, 900 MHz, 915 MHz, 930 MHz Output power of signal generator 0.0 dBm Attenuator and cable loss 20.6 dB at 865/868 MHz, 20.5 dB at 900/915/930 MHz Power at antenna - 20.6 dBm / - 20.5 dBm The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 3 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential Photo documentation of EUT with temporary antenna connector The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 4 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 5 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential The turntable is rotated counter-clockwise. The starting point of the measurement is the position shown in the test setup photos. This leads to the following relationship in the polar plots of the test result graphs: EUT X position EUT Y position The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 6 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential EUT Z position: The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 7 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential Test results for test instruments and accessories used see CPR 3 Peak performance overview Peak Gain (dBi) X hor X ver Y hor Y ver Z hor Z ver 865 MHz -8.6 -4.9 -21.1 1.2 1.8 -19.2 868 MHz -8.4 -5.0 -18.8 1.2 1.8 -18.9 900 MHz -6.6 -5.8 -16.8 2.9 2.6 -14.7 915 MHz -6.3 -6.6 -17.8 3.0 2.5 -14.0 930 MHz -6.2 -7.3 -17.3 3.7 2.4 -13.2 The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 8 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential Detailed graphical representation x direction, 865 MHz, horizontal x direction, 865 MHz, vertical The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 9 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential x direction, 868 MHz, horizontal x direction, 868 MHz, vertical The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH Order No.: 80240901-00 Rev_0, Page 10 of 23 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360 Rev. Nr. 3.6 2020-02-12 CSA Confidential x direction, 900 MHz, horizontal x direction, 900 MHz, vertical The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without …

Text truncated - open the document above for the full version.

PHOENIX TESTLAB GmbH Date: 2025-09-10 Product Certification Department Koenigswinkel 10 32825 Blomberg Germany Attestation FCC Justification Statement about Compliance for FHSS Device FCC ID: SZO-RR21 FCC Rule Part Section: FCC 15.247(a)(1) i) Pseudorandom frequency hopping sequence Describe how the hopping sequence is generated. Provide an example of the hopping sequence channels, to demonstrate that the sequence meets the requirement specified in the definition of an FHSS system, found in Section 2.1(c). Per the definition in Section 2.1(c), the hop set shall appear as random in the near term, shall appear as evenly distributed in the long term, and sequential hops shall be randomly distributed in both direction and magnitude of change. Response: The channel center frequencies of this device range from 902.75 MHz to 927.25 MHz. It uses 50 hopping channels with a 20 dB BW less than 250 kHz separated by 500 kHz. ii) Equal hopping frequency use Describe how each individual EUT meets the requirement that each of its hopping channels is used equally on average (e.g., that each new transmission event begins on the next channel in the hopping sequence after the final channel used in the previous transmission event). Response: A set of 50 random channels is shuffled with a true random generator peripheral. This list is then used sequentially for the next 50 transmissions. After going through the set of 50 channels, the next set is shuffled. To avoid shuffling the last channel as the first of the next set, shuffling is redone in this case. iii) System receiver input bandwidth Describe how the associated receiver(s) complies with the requirement that the input bandwidth (either RF or IF) matches the bandwidth of the transmitted signal. Response: All 50 channels are evenly used by the mechanism shown in clause ii. iv) System receiver hopping capability Describe how the associated receiver(s) has the ability to shift frequencies in synchronization with the transmitted signals. Response: The LF bandwidth of the receiver is 350kHz centered at 0 Hz (direct conversion) followed by digital filtering in the digital part of the receiver. The bandwidth if the digital filter depends on the tag data rate on the air interface. If you have any questions, please feel free to contact me Contact Person: Nikias Klohr Position in the Company: CTO & Head of R&D Date of Signature: 2025-09-10

Authority to Act as Agent Date: September 13, 2024 Phoenix Test Lab GmbH CSA Group Bayern GmbH, Ms. Marie-Luise Schuster / Mr. Patrick Lehner / Mr. Stefan Sauerborn is authorized to act on our behalf, until otherwise notified, for applications to Phoenix Test Lab GmbH. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, This authorization is valid until further written notice from race result AG. By:__________________________Nikias Klohr (Signature) Title:Head of R&D On behalf of Cert Holder:race result AG Address:Joseph-von-Fraunhofer-Strasse 11, 76327 Pfinztal, Germany Telephone:+49 721 9969900 Email: [email protected]

External Photos:

Label:

The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH File No. 80240901-10 Rev_0, page 1 of 10 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.4, 2024-07-01 CSA Confidential R F − T E S T R E P O R T - Human Exposure - Type / Model Name : RR21 Product Description : UHF RFID Reader Applicant : race result AG Address : Joseph-von-Fraunhofer-Str. 11 76327 PFINZTAL, GERMANY Manufacturer : race result AG Address : Joseph-von-Fraunhofer-Str. 11 76327 PFINZTAL, GERMANY Test Result according to the standards listed in clause 1 test standards: POSITIVE Test Report No. : 80240901-10 Rev_0 25. July 2025 ______________________________________________________________________________________________ Date of issue The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . FCC ID: SZO-RR21 IC ID: 20465-RR21 CSA Group Bayern GmbH File No. 80240901-10 Rev_0, page 2 of 10 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.4, 2024-07-01 CSA Confidential Contents 1 T E S T S T A N D A R D S 3 2 E Q U I P M E N T U N D E R T E S T 4 2.1 Information provided by the Client 4 2.2 Sampling 4 2.3 Photo documentation of the EUT – See ATTACHMENT A 4 2.4 Equipment type, category 4 2.5 Short description of the equipment under test (EUT) 4 2.6 Variants of the EUT 4 2.7 Operation frequency and channel plan 5 2.8 Transmit operating modes 5 2.9 Antennas 5 2.10 Power supply system utilised 5 3 T E S T R E S U L T S U M M A R Y 6 3.1 Revision history of test report 6 3.2 Final assessment 6 4 T E S T E N V I R O N M E N T 7 4.1 Address of the test laboratory 7 4.2 Environmental conditions 7 4.3 Statement of the measurement uncertainty 7 5 H U M A N E X P O S U R E 8 5.1 RF output power 8 5.2 SAR exemption consideration according to FCC 9 5.3 SAR exemption consideration according to ISED 10 ATTACHMENT A as separate supplement The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . FCC ID: SZO-RR21 IC ID: 20465-RR21 CSA Group Bayern GmbH File No. 80240901-10 Rev_0, page 3 of 10 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.4, 2024-07-01 CSA Confidential 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules and Regulations Part 1, Subpart I - Procedures Implementing the National Environmental Policy Act of 1969 Part 1, Subpart I, Section 1.1310 Radiofrequency radiation exposure limits Part 1, Subpart 2, Section 2.1091 Radiofrequency radiation exposure evaluation: mobile devices. Part 1, Subpart 2, Section 2.1093 Radiofrequency radiation exposure evaluation: portable devices. KDB 447498 D04 RF Exposure procedures and equipment authorisation policies for mobile and portable devices, April 20, 2021. ANSI C95.1: 2005 IEEE Standard for Safety Levels with respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz ETSI TR 100 028 V1.3.1: 2001-03, Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Uncertainties in the Measurement of Mobile Radio Equipment Characteristics—Part 1 and Part 2 The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . FCC ID: SZO-RR21 IC ID: 20465-RR21 CSA Group Bayern GmbH File No. 80240901-10 Rev_0, page 4 of 10 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.4, 2024-07-01 CSA Confidential 2 E Q U I P M E N T U N D E R T E S T 2.1 Information provided by the Client Please note, we do not take any responsibility for information provided by the client or his representative which may have an influence on the validity of the test results. 2.2 Sampling The customer is responsible for the choice of sample. Sample configuration, start-up and operation is carried out by the customer or according his/her instructions. 2.3 Photo documentation of the EUT – See ATTACHMENT A 2.4 Equipment type, category UHF-RFID Reader, FHSS, mobile equipment. 2.5 Short description of the equipment under test (EUT) The UHF RFID Reader (Ultra High Frequency Radio Frequency Identification) is designed to read information stored on RFID tags. The device is DC powered and managed by an external controller via a CAN Bus (Controller Area Network). Number of tested samples: --- Serial number: --- Firmware version: --- 2.6 Variants of the EUT There are no variants. The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . FCC ID: SZO-RR21 IC ID: 20465-RR21 CSA Group Bayern GmbH File No. 80240901-10 Rev_0, page 5 of 10 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.4, 2024-07-01 CSA Confidential 2.7 Operation frequency and channel plan The operating frequency is 902 MHz to 928 MHz. Channel plan: Channel No. Frequency (MHZ) Channel No. Frequency (MHZ) Channel No. Frequency (MHZ) 1 902.75 21 912.75 41 922.75 2 903.25 22 913.25 42 923.25 3 903.75 23 913.75 43 923.75 4 904.25 24 914.25 44 924.25 5 904.75 25 914.75 45 924.75 6 905.25 26 915.25 46 925.25 7 905.75 27 915.75 47 925.75 8 906.25 28 916.25 48 926.25 9 906.75 29 916.75 49 926.75 10 907.25 30 917.25 50 927.25 11 907.75 31 917.75 12 908.25 32 918.25 13 908.75 33 918.75 14 909.25 34 919.25 15 909.75 35 919.75 16 910.25 36 920.25 17 910.75 37 920.75 18 911.25 38 921.25 19 911.75 39 921.75 20 912.25 40 922.25 2.8 Transmit operating m…

Text truncated - open the document above for the full version.

The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . CSA Group Bayern GmbH File No. 80240901-06 Rev_1, page 1 of 64 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.5 2021-11-04 CSA Confidential R F − T E S T R E P O R T - FCC Part 15.247, RSS-247 - Type / Model Name : RR21 Product Description : UHF RFID Reader Applicant : race result AG Address : Joseph-von-Fraunhofer-Str. 11 76327 PFINZTAL, GERMANY Manufacturer : race result AG Address : Joseph-von-Fraunhofer-Str. 11 76327 PFINZTAL, GERMANY Test Result according to the standards listed in clause 1 test standards: POSITIVE Test Report No. : 80240901-06 Rev_1 19. August 2025 ______________________________________________________________________________________________ Date of issue The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . FCC ID: SZO-RR21 IC ID: 20465-RR21 CSA Group Bayern GmbH File No. 80240901-06 Rev_1, page 2 of 64 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.5 2021-11-04 CSA Confidential Contents 1 T E S T S T A N D A R D S 3 2 E Q U I P M E N T U N D E R T E S T 4 Information provided by the Client 4 Sampling 4 Photo documentation of the EUT – Detailed photos see ATTACHMENT A 4 Equipment type 4 Short description of the equipment under test (EUT) 4 Variants of the EUT 4 Operation frequency and channel plan 5 Antenna 5 Power supply system utilised 5 Peripheral devices and interface cables 6 Determination of worst-case conditions for final measurement 6 3 T E S T R E S U L T S U M M A R Y 8 Revision history of test report 8 Final assessment 9 4 T E S T E N V I R O N M E N T 10 Address of the test laboratory 10 Environmental conditions 10 Statement of the measurement uncertainty 10 Conformity Decision Rule 11 Measurement protocol for FCC and ISED 11 5 T E S T C O N D I T I O N S A N D R E S U L T S 14 AC power line conducted emissions 14 Emission bandwidth 18 Maximum peak output power 23 Spurious emissions conducted 25 Band edge compliance 33 Spurious emissions radiated 37 Dwell time 54 Carrier frequency separation 57 Number of hopping channels 60 Antenna application 63 6 U S E D T E S T E Q U I P M E N T A N D A C C E S S O R I E S 64 ATTACHMENT A as separate supplement The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . FCC ID: SZO-RR21 IC ID: 20465-RR21 CSA Group Bayern GmbH File No. 80240901-06 Rev_1, page 3 of 64 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.5 2021-11-04 CSA Confidential 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules and Regulations Part 15, Subpart A - General (February 2025) Part 15, Subpart A, Section 15.31 Measurement standards Part 15, Subpart A, Section 15.33 Frequency range of radiated measurements Part 15, Subpart A, Section 15.35 Measurement detector functions and bandwidths FCC Rules and Regulations Part 15, Subpart C - Intentional Radiators (February 2025) Part 15, Subpart C, Section 15.203 Antenna requirement Part 15, Subpart C, Section 15.204 External radio frequency power amplifiers and antenna modifications Part 15, Subpart C, Section 15.207 Conducted limits Part 15, Subpart C, Section 15.209 Radiated emission limits, general requirements Part 15, Subpart C, Section 15.247 Operation within the bands 902 - 928 MHz, 2400 - 2483.5 MHz and 5725 - 5850 MHz ANSI C63.10: 2013 Testing Unlicensed Wireless Devices ETSI TR 100 028 V1.3.1: 2001-03, Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Uncertainties in the Measurement of Mobile Radio Equipment Characteristics—Part 1 and Part 2 KDB 558074 D01 v05r02 Guidance for compliance measurements on DTS; FHSS and hybrid system devices operating under Section 15.247 of the FCC rules, April 2, 2019. The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . FCC ID: SZO-RR21 IC ID: 20465-RR21 CSA Group Bayern GmbH File No. 80240901-06 Rev_1, page 4 of 64 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.5 2021-11-04 CSA Confidential 2 E Q U I P M E N T U N D E R T E S T Information provided by the Client Please note, we do not take any responsibility for information provided by the client or his representative which may have an influence on the validity of the test results. Sampling The customer is responsible for the choice of sample. Sample configuration, start-up and operation is carried out by the customer or according his/her instructions. Photo documentation of the EUT – Detailed photos see ATTACHMENT A Equipment type UHF-RFID Reader, FHSS, mobile equipment. Short description of the equipment under test (EUT) The UHF RFID Reader (Ultra High Frequency Radio Frequency Identification) is designed to read information stored on RFID tags. The device is DC powered and managed by an external controller via a CAN Bus (Controller Area Network). Number of tested samples: 2 Serial number: 250204061 (radiated sample) 250207001 (conducted sample) SW/FW version: rev105 (ae09bad9) Variants of the EUT There are no variants. The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permissi on of the test laboratory . FCC ID: SZO-RR21 IC ID: 20465-RR21 CSA Group Bayern GmbH File No. 80240901-06 Rev_1, page 5 of 64 Straubinger Straße 100  94447 Plattling  GERMANY Tel.:+49(0)9931-98360  Fax:+49(0)9931-9836440 Rev. No. 6.5 2021…

Text truncated - open the document above for the full version.

Test Setup Photos FCC 15.247 AC Powerline Conducted Spurious emissions radiated