SZQ-T110TYLT Vu Solo

WirelessCharger For more information on the Qi, wireless charging, Qi™ Charging Standard and a list of compatible smartphones, please visit: www.TYLT.com/VÜ©2014 TYLT. All rights reserved. TYLT ® and the TYLT ® logo are registered trademarks of Foreign Trade Corp. Other marks are the property or their respective owners. IC3603 SPECIFICATIONS - Input: 5V, 1.8A • Output: 5V, 1A CAUTION The Vu Solo is for charging wireless charging enabled and Qi™ Charging Standard compatible smartphones only. The charging unit should only be used at normal indoor room conditions. Place charger on a hard flat surface. For best results, use the supplied USB power cable and a 5V USB power supply with an output power of 1.8A or greater. Vu Solo may become warm during charging. Avoid direct contact with highly flammable materials. Avoid contact with delicate furniture finishes. CARE AND MAINTENANCE GENERAL - Keep Device Dry. Do NOT expose the device to liquids. If device gets wet, immediately unplug it and allow it to dry. Do not disassemble or attempt repair. Do not store the device in high or low temperatures. STICKY SUCTION - Place Charger on a dry, clean, flat, smooth surface. It will adhere immediately without any pressure needed. To remove, pull up one corner slowly and gently. Be Patient. To clean sticky suction, use soft, damp cloth or scotch tape. Do NOT use solvents, alcohol or cleaners. POWERING DEVICEPower-up the Vu Solo by inserting the included Micro-USB power cable into the power port. Insert the included USB cable into a USB Power Supply.* POSITIONING YOUR DEVICE Place your Qi™ compatible device on the charging pad to begin charging. To find your devices charging spot, keep your device centered on the pad horizontally. Move your device forward or to a devices features. Check www.tylt.com/vu-solo for more information and a demonstration of alignment. LED INDICATORWhile in Standby mode, the LED is OFF. Solid green LED indicates Vu Solo is delivering full power. Slow blinking indicates limited power source.For best performance, use a USB power supply that delivers more current. TROUBLESHOOTING Under any type of electronic error condition, the Green LED will begin to Blink. A fast blink indicates a Fault. Remove the phone and place it back on the Vu Solo. If problem persists, unplug the Vu Solo from power source and re-connect it. If LED is blinking slowly, power is being transmitted, but may be slower than optimal. For optimal results, use a USB power supply with a power output of greater than 1.8A.If the green LED is on but no power is being received by the device, there may be a metal object near the coils. Pick up the device and remove foreign objects and place device back on the Vu Solo. This is a safety feature and normal operation. * Note: USB power supply is not included. Vu Solo Wireless ChargerMicro-USB power cable w/ Alignment Ledge PACKAGE CONTENTS ENG backward slowly until your device starts charging.If the device does not start charging, continue to move your device slowly forward or backward, stopping for 2 seconds every ¼ inch (or 5mm).Once the device is charging, the alignment ledge can be set to enable quick placement next time the Vu Solo is used. Simply move the alignment ledge forward until it touches the top of the devices. CHARGING YOUR DEVICE Next time the device is ready to wirelessly charge, make sure the top of the device is touching the ledge as you set it onto the pad, and charging should begin seamlessly. You can also use the alignment tabs located on either side of the silicone pad to help visually align SPECIFICATIONS - Input: 5V, 1.8A • Output: 5V, 1A CAUTION The Vu Solo is for charging wireless charging enabled and Qi™ Charging Standard compatible smartphones only. The charging unit should only be used at normal indoor room conditions. Place charger on a hard flat surface. For best results, use the supplied USB power cable and a 5V USB power supply with an output power of 1.8A or greater. Vu Solo may become warm during charging. Avoid direct contact with highly flammable materials. Avoid contact with delicate furniture finishes. CARE AND MAINTENANCE GENERAL - Keep Device Dry. Do NOT expose the device to liquids. If device gets wet, immediately unplug it and allow it to dry. Do not disassemble or attempt repair. Do not store the device in high or low temperatures. STICKY SUCTION - Place Charger on a dry, clean, flat, smooth surface. It will adhere immediately without any pressure needed. To remove, pull up one corner slowly and gently. Be Patient. To clean sticky suction, use soft, damp cloth or scotch tape. Do NOT use solvents, alcohol or cleaners. POWERING DEVICEPower-up the Vu Solo by inserting the included Micro-USB power cable into the power port. Insert the included USB cable into a USB Power Supply.* POSITIONING YOUR DEVICE Place your Qi™ compatible device on the charging pad to begin charging. To find your devices charging spot, keep your device centered on the pad horizontally. Move your device forward or to a devices features. Check www.tylt.com/vu-solo for more information and a demonstration of alignment. LED INDICATORWhile in Standby mode, the LED is OFF. Solid green LED indicates Vu Solo is delivering full power. Slow blinking indicates limited power source.For best performance, use a USB power supply that delivers more current. TROUBLESHOOTING Under any type of electronic error condition, the Green LED will begin to Blink. A fast blink indicates a Fault. Remove the phone and place it back on the Vu Solo. If problem persists, unplug the Vu Solo from power source and re-connect it. If LED is blinking slowly, power is being transmitted, but may be slower than optimal. For optimal results, use a USB power supply with a power output of greater than 1.8A.If the green LED is on but no power is being received by the device, there may be a metal object near the coils. Pick up the device and remove foreign objects and place device back on the Vu Solo. This is a …

Text truncated - open the document above for the full version.

Foreign Trade Corporation dba. Technocel AGENCY AUTHORIZATION LETTER Federal Communications Commission Authorization and Evaluation Division FCC ID: SZQ-T110 Date：2014/9/11 To whom it may concern: We, the undersigned, hereby authorize Richard Li from SGS-CSTC Standards Technical Services Co., Ltd. to act on our behalf, as our agent, in the following matters related to the FCC approval of our product: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by Richard Li within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months from original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, -------------------------------------- Name/Title Vahid Zarie/CTO Company Name: Foreign Trade Corporation dba. Technocel Address: 130 W Cochran St

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 6/20-2014 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name SZQ‐T110 VUSOLOx-T For the product stated above, we request permanent confidentiality for exhibits which contain Operational Description, Block Diagram, and Schematics. The above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Vahid Zarie CTO ( Chief Technical Officer)

External Photos

Version Date/Sign CR No. Material: Colour: Product: Title: Scale Associated Sys CorelDRAW13 Design Draw Check Appd VU Single Type label_SW06A00L_Blue_Universal 1:1 13.04.14 15.07.14 Dwang Dwang Code: ZzXXXX See Note(Material description) See Note(Material description) Draw: 600XXX Scan 1:1 Note: YY = Year,2 digits (12=2012, 13=2013, 14=2014,etc.) MM= Month, 2 digits from 01-12 SS= Series number 6 digits staring from 0...01 every month LL= Production line number , 2 digits ... Barcode: YYMMSSSSSSLL Material description: 1. Material: 0.05mm matte silver PET film; 2. Surface: 0.025mm matte transparent OPP film; 3. Printing: Black background; 4. Material must fulfill Gwi 4-11 Salcomp Hazardous Substances Management Standard latest version. MODEL: VUSOLOBL-TMODEL:VUSOLOBL-T 4+/-0.2 mm4+/-0.2mm Size 10*10mm Size 12*12mm 3.7+/-0.2mm INPUT: DC 5V,1.8AINPUT:DC5V,1.8A OUTPUT: 5WOUTPUT:5W FCC ID: SZQ-T110FCCID:SZQ-T110

Internal Photos

SGS-CSTC Standards Technical Services Co., Ltd. 19 8 Ke zhu Roa d, Scient ech Park, Guangzhou Economic & Technolo gical De velopment D istrict, Guangzhou, China 510663 Telephon e: +86 (0) 20 8 2155555 Fax: +86 (0) 20 820750 59 Email: ee. guangzh [email protected] Report No.: GZEM140800456801 Page: 1 of 11 FCC ID: SZQ-T110 Authorized Signature: Richard Li Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1408004568RF Applicant: Salcomp (Shenzhen) Co., Ltd. Manufacturer: Salcomp (Shenzhen) Co., Ltd. Factory: Salcomp (Shenzhen) Co., Ltd. Salcomp Industrial Eletrônica da Amazônia Ltda Salcomp Manufacturing India Pvt Ltd. FCC ID: SZQ-T110 Product Name: TYLT Vu Solo Product Description: Low Power Transmitter Model No.: VUSOLOx-T, the x is color code , which may be “GY”,”G”,”RD”and”BL”,GY=Grey, G=Green ,RD=Red, BL= Blue ♣ ♣ Please refer to section 3 of this report for further details. Trade mark: TYLT Standards: KDB 680106 D01v02. Date of Receipt: 2014-08-29 Date of Test: 2014-09-03 to 2014-09-04 Date of Issue: 2014-09-12 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further detail. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140800456801 Page: 2 of 11 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-09-12 Original Authorized for issue by: Tested By 2014-09-03 to 2014-09-04 (Jack Liang) /Project Engineer Date Prepared By 2014-09-12 (Jack Liang) /Project Engineer Date Checked By 2014-09-12 (Fred Zhu) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140800456801 Page: 3 of 11 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 3 Content 1 COVER PAGE ............................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. 198 Kezhu Road, Scientech Park, Guangzhou Economic & Technological Development District, Guangzhou, China 510663 Telephone: +86 (0) 20 82155555 Fax: +86 (0) 20 82075059 Email: [email protected] Report No.: GZEM140800456801 Page: 1 of 31 FCC ID: SZQ-T110 Authorized Signature: Richard Li Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1408004568RF Applicant: Salcomp (Shenzhen) Co., Ltd. Manufacturer: Salcomp (Shenzhen) Co., Ltd. Factory: Salcomp (Shenzhen) Co., Ltd. Salcomp Industrial Eletrônica da Amazônia Ltda Salcomp Manufacturing India Pvt Ltd. FCC ID: SZQ-T110 Product Name: TYLT Vu Solo Product Description: Low Power Transmitter Model No.: VUSOLOx-T, the x is color code , which may be “GY”,”G”,”RD”and”BL”,GY=Grey, G=Green ,RD=Red, BL= Blue ♣ ♣ Please refer to section 3 of this report for further details. Trade Mark: TYLT Standards: CFR 47 FCC PART 15 SUBPART C:2013 section 15.207 CFR 47 FCC PART 15 SUBPART C:2013 section 15.209 Date of Receipt: 2014-08-29 Date of Test: 2014-09-03 to 2014-09-04 Date of Issue: 2014-09-12 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further details. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140800456801 Page: 2 of 31 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-09-12 Original Authorized for issue by: Tested By 2014-09-03 to 2014-09-04 (Jack Liang) /Project Engineer Date Prepared By 2014-09-12 (Jack Liang) /Project Engineer Date Checked By 2014-09-12 (Fred Zhu) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140800456801 Page: 3 of 31 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained f…

Text truncated - open the document above for the full version.

Test Setup Photos 1.1 RADI ATE D SP URI OU S EM ISSIO N TE ST SETUP 9kHz to 30MHz: 30 MHz to 1 GHz: 1.2 CON DU CTED EM ISSI ON TEST SETUP