SZQ-T130Verizon Wireless Charging Pad

Specifications:Input: 5V / 1.8AOutput: 5V, 1A Included:Verizon Qi Wireless Charging Pad5V Power Adapter VERIZON Qi WIRELESS CHARGING PAD * Use the included power supply for fastest charging rate. Using a power supply rated under 1.8A will cause the phone to charge slower, indicated by a blinking red LED Remove protective film from base. Place charger on a dry, clean, flat, smooth surface. It will adhere immediately without any pressure needed. To remove or reposition, pull up one corner slowly and gently. Power-up the Verizon Qi Wireless Charging Pad by inserting the included Micro-USB power cord into the power port*. Place your Qi™ compatible device on the charging pad to begin charging. ICXXXX While in Standby mode, the LED is OFF. Solid red LED indicates Verizon Qi Wireless Charging Pad is delivering full power. If the red LED is on but no power is being received by the device, there may be a metal object near the coils. Pick up the device and remove foreign objects and place device back on the Verizon Qi Wireless Charging Pad. This is a safety feature and normal operation. StandbyCharging LED indicator light To find your devices charging spot, keep your device centered on the pad horizontally.Now move your device up or down slowly until your device starts charging. Note: If your device does not start charging, continue to move your device slowly up or down, stopping for 2 seconds every ¼ inch. When the red light appears on the charging pad, your device should be charging. To help achieve proper charging placement next time, make note of buttons or home screen features in relation to the charging pad surface. CAUTIONS The Verizon Qi Wireless Charging Pad works with Qi Wireless Charging compatible smartphones and devices. The charging unit should only be used at normal indoor room conditions. Place charger on a hard flat surface. Use the supplied 5V 1.8A power adapter included with the Verizon Qi Wireless Charging Pad. The Verizon Qi Wireless Charging Pad and your smartphone/device may become warm during charging. Avoid direct contact with highly flammable materials. Avoid contact with delicate furniture finishes. FCC InformationThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules [and with RSS-210 of Industry Canada].Operation is subject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.To comply with FCC and other RF exposure requirements, please maintain a distance of 20cm between the charger and your body when in use.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Changes or modifications made to this equipment not expressly approved by the manufacturer may void the FCC authorization to operate this equipment.FCC ID: SZQ-T130 CARE AND MAINTENANCE (General)Keep Device Dry. Do NOT expose the device to liquids. If device gets wet, immediately unplug it and allow it to dry.Do not disassemble or attempt repair. Do not store the device in high or low temperatures. CARE AND MAINTENANCE (Sticky Suction)To clean the charging pad base, use soft, damp cloth or scotch tape. Do NOT use solvents, alcohol or cleaners.

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 6/20-2014 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name SZQ‐T130 VZW1COIL-WC For the product stated above, we request permanent confidentiality for exhibits which contain Operational Description, Block Diagram, and Schematics. The above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Vahid Zarie CTO ( Chief Technical Officer)

Foreign Trade Corporation dba. Technocel AGENCY AUTHORIZATION LETTER Federal Communications Commission Authorization and Evaluation Division FCC ID: SZQ-T130 Date：2014/9/11 To whom it may concern: We, the undersigned, hereby authorize Richard Li from SGS-CSTC Standards Technical Services Co., Ltd. to act on our behalf, as our agent, in the following matters related to the FCC approval of our product: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by Richard Li within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months from original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, -------------------------------------- Name/Title Vahid Zarie/CTO Company Name: Foreign Trade Corporation dba. Technocel Address: 130 W Cochran St

External Photos

Internal Photos

SGS-CSTC Standards Technical Services Co., Ltd. 19 8 Ke zhu Roa d, Scient ech Park, Guangzhou Economic & Technolo gical De velopment D istrict, Guangzhou, China 510663 Telephon e: +86 (0) 20 8 2155555 Fax: +86 (0) 20 820750 59 Email: ee. guangzh [email protected] Report No.: GZEM140800414401 Page: 1 of 11 FCC ID: SZQ-T130 Authorized Signature: Richard Li Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1408004144RF Applicant: Salcomp (Shenzhen) Co., Ltd. Manufacturer: Salcomp (Shenzhen) Co., Ltd. Factory: Salcomp (Shenzhen) Co., Ltd. Salcomp Industrial Eletrônica da Amazônia Ltda Salcomp Manufacturing India Pvt Ltd. FCC ID: SZQ-T130 Product Name: Verizon Wireless Charging Pad Product Description: Low Power Transmitter Model No.: VZW1COIL-WC Trade mark: Verizon Standards: KDB 680106 D01v02. Date of Receipt: 2014-08-13 Date of Test: 2014-08-28 to 2014-08-29 Date of Issue: 2014-09-09 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further detail. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140800414401 Page: 2 of 11 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-09-09 Original Authorized for issue by: Tested By 2014-08-28 to 2014-08-29 (Jack Liang) /Project Engineer Date Prepared By 2014-09-09 (June Chen) /Clerk Date Checked By 2014-09-09 (Fred Zhu) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140800414401 Page: 3 of 11 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 3 Content 1 COVER PAGE ...................................................................................................................................................... 1 2 VERSION .............…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. 198 Kezhu Road, Scientech Park, Guangzhou Economic & Technological Development District, Guangzhou, China 510663 Telephone: +86 (0) 20 82155555 Fax: +86 (0) 20 82075059 Email: [email protected] Report No.: GZEM140800414401 Page: 1 of 31 FCC ID: SZQ-T130 Authorized Signature: Richard Li Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1408004144RF Applicant: Salcomp (Shenzhen) Co., Ltd. Manufacturer: Salcomp (Shenzhen) Co., Ltd. Factory: Salcomp (Shenzhen) Co., Ltd. Salcomp Industrial Eletrônica da Amazônia Ltda Salcomp Manufacturing India Pvt Ltd. FCC ID: SZQ-T130 Product Name: Verizon Wireless Charging Pad Product Description: Low Power Transmitter Model No.: VZW1COIL-WC Trade Mark: Verizon Standards: CFR 47 FCC PART 15 SUBPART C:2013 section 15.207 CFR 47 FCC PART 15 SUBPART C:2013 section 15.209 Date of Receipt: 2014-08-13 Date of Test: 2014-08-28 to 2014-08-29 Date of Issue: 2014-09-09 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further details. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140800414401 Page: 2 of 31 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-09-09 Original Authorized for issue by: Tested By 2014-08-28 to 2014-08-29 (Jack Liang) /Project Engineer Date Prepared By 2014-09-09 (June Chen) /Clerk Date Checked By 2014-09-09 (Fred Zhu) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM140800414401 Page: 3 of 31 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 3 Test Summary ELECTROMAGNETIC INTERFERENCE (EMI) Test Test Requirement Test Method Class / Severity Result Radiated Emission (9 kH…

Text truncated - open the document above for the full version.

Test Setup Photos 1.1 RADI ATE D SP URI OU S EM ISSIO N TE ST SETUP 9kHz to 30MHz: 30 MHz to 1 GHz: 1.2 CON DU CTED EM ISSI ON TEST SETUP