T54AD701-KAD701-KRECEIVER

AD701‐KRECEIVER User’s Manual Model: AD701‐K FCC ID: T54AD701‐K TFT Multimedia Color Monitor CH AN- M AN+ AD701-K Power 1 4 3 2 5 6 Matching switch Channel Switch Back / / Volume up-/ Menu OK button/ volume Down+/ Audio jack 1Connect to power adapter press button 2 seconds to power on press again to power off . /: , , . On Off 1 2 Matching operate：Power on press camera matching switch . , . press button 5 senconds then . 2 4 Motion Detection press enter menu enter REC SETUP then enter ME RECORD pressto choose 5S MD record 10S MD record and on alwayse record after setup press to confim and press back to exit . : , , , , ( ). , . / 4 35 4 5 Playback：press enter menu enter REC SETUP then enter VIDEO pressto choose the video file and press to playback press to pause and press to stop playback press to exit . , , , , . , . / 4 3 5 4 54 2 3 Chanell switch In the video screen press to switch channel 1 4 .: , - 2 6 Quarter screen press enter menu enter MODE SETUP press to confim press exit. . : , , , press to choose 4VS1 MODE(Quarter screen mode),SCAN MODE (Automatic cycle mode and 1VS1 MODE(Single screen mode), ) / 4 35 4 2 7 Date/time Settings: press enter menu enter CLOCK SETUP Press the can adjust the time and date ., , /, , , Press can be switching between time and date After the completion of the set press to exit 4 354 2 IMPORTANT REGULATORY INFORMATION This device complies with Part 15 of the FCC Rules: Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference that is received, including any interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

May 18, 2012 Federal Communication Commission Authorization and Evaluation Division FCC ID: T54AD701-K Re: Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below: 1: Block Diagram 2: Circuit Diagram 3: Operational Description 4: Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rules 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Wang Gang AnJieLun Electronic Techology Limited

TOP VIEW OF SAMPLE BOTTOM VIEW OF SAMPLE LEFT VIEW OF SAMPLE RIGHT VIEW OF SAMPLE FRONT VIEW OF SAMPLE BACK VEIW OF SAMPLE ALL VIEW OF SAMPLE

AD701-KRECEIVER Model Name: AD701-K FCC ID: T54AD701-K

INTERNAL VIEW OF SAMPLE – 1 INTERNAL VIEW OF SAMPLE – 2 INTERNAL VIEW OF SAMPLE – 3 INTERNAL VIEW OF SAMPLE – 4 INTERNAL VIEW OF SAMPLE – 5 INTERNAL VIEW OF SAMPLE – 6 INTERNAL VIEW OF SAMPLE - 7

Radio Test Report Report No.: AGC20M120302‐2F2 FCC ID : T54AD701‐K PRODUCT DESIGNATION : AD701‐KRECEIVER BRAND NAME : N/A MODEL NAME : AD701‐K CLIENT : AnJieLun Electronic Techology Limited DATE OF ISSUE : May 08, 2012 STANDARD(S) : FCC Part 15 Rules REPORT VERSION : V1.0 Attestation of Global Compliance Co., Ltd. CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC20M120302-2F2 Page 1 of 42 VERIFICATION OF COMPLIANCE Applicant AnJieLun Electronic Techology Limited 2F, 12st, LONGBI INDUSTRIAL PARK, BANTIAN VILLAGE, BUJI TOWN, SHENZHEN, GUANG DONG PROVIDENCE, CHINA Manufacturer AnJieLun Electronic Techology Limited 2F, 12st, LONGBI INDUSTRIAL PARK，BANTIAN VILLAGE, BUJI TOWN，SHENZHEN, GUANG DONG PROVIDENCE, CHINA Product Designation AD701-KRECEIVER Brand Name N/A Test Model AD701-K Report Number AGC20M120302-2F2 Date of Test May 04, 2012 to May 07, 2012 WE HEREBY CERTIFY THAT: The above equipment was tested by Attestation of Global Compliance Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C 63.4:2003. The sample tested as described in this report is in compliance with the FCC Rules Part 15 requirements. Tested By: Curoky Chen May 08, 2012 Reviewed By: Forrest Lei May 08, 2012 Approved By: Solger Zhang May 08, 2012 Report No.: AGC20M120302-2F2 Page 2 of 42 TABLE OF CONTENTS 1 GENERAL INFORMATION ..................................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION ........................................................................................................................................ 4 1.2 RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................................ 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ........................................................................................................................................................... 5 1.5 SPECIAL ACCESSORIES ......................................................................................................................................... 5 1.6 EQUIPMENT MODIFICATIONS ................................................................................................................................ 5 2 SYSTEM TEST CONFIGURATION ....................................................................................................................................... 6 2.1 CONFIGURATION OF EUT SYSTEM ..................................................................................................................... 6 2.2 EQUIPMENT USED IN EUT SYSTEM .................................................................................................................... 6 3 SUMMARY OF TEST RESULTS ............................................................................................................................................ 7 4. DESCRIPTION OF TEST MODES ....................................................................................................................................... 8 5 PEAK OUTPUT POWER ......................................................................................................................................................... 9 5.1 MEASUREMENT PROCEDURE .................................................................................................................................... 9 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ..................................................................................... 9 5.3 MEASUREMENT EQUIPMENT USED ........................................................................................................................ 10 5.4 LIMITS AND MEASUREMENT RESULT .................................................................................................................... 10 6 20 DB BANDWIDTH ............................................................................................................................................................. 11 6.1 MEASUREMENT PROCEDURE .................................................................................................................................. 11 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................................... 11 6.3 MEASUREMENT EQUIPMENT USED ........................................................................................................................ 11 6.4 LIMITS AND MEASUREMENT RESULTS .................................................................................................................. 11 7. CONDUCTED SPURIOUS EMISSION .............................................................................................................................. 13 7.1 MEASUREMENT PROCEDURE .................................................................................................................................. 13 7.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................................... 13 7.3 MEASUREMENT EQUIPMENT USED ........................................................................................................................ 13 7.4 LIMITS AND MEASUREMENT RESULT .................................................................................................................... 13 8. RADIATED EMISSION ......................................................................................................................................................... 15 8.…

Text truncated - open the document above for the full version.

OET Bulletin 65 (MPE) Test Report Report No.: AGC20M120302‐2F7 FCC ID : T54AD701‐K PRODUCT DESIGNATION : AD701‐KRECEIVER BRAND NAME : N/A TEST MODEL : AD701‐K CLIENT : AnJieLun Electronic Techology Limited DATE OF ISSUE : May 08, 2012 STANDARD(S) : OET Bulletin 65 REPORT VERSION : V1.0 Attestation of Global Compliance Co., Ltd. 1. CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC20M120302-2F7 Page 1 of 7 TABALE OF CONTENTS TABALE OF CONTENTS .................................................................................................................................. 1 1. TEST RESULT CERTIFICATION ................................................................................................................. 2 2. TECHNICAL INFORMATION....................................................................................................................... 3 2.1 EUT DESCRIPTION ..................................................................................................................................... 3 3. RF EXPOSURE MEASUREMENT .............................................................................................................. 4 3.1 INTRODUCTION .......................................................................................................................................... 4 3.2 FCC LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE(MPE) .............................................................. 5 4. CLASSIFICATION OF THE ASSESSMENT METHODS ............................................................................... 6 Report No.: AGC20M120302-2F7 Page 2 of 7 1. TEST RESULT CERTIFICATION Applicant Name: AnJieLun Electronic Techology Limited Address: 2F, 12st, LONGBI INDUSTRIAL PARK, BANTIAN VILLAGE, BUJI TOWN, SHENZHEN, GUANG DONG PROVIDENCE, CHINA Manufacturer Name: AnJieLun Electronic Techology Limited Address: 2F, 12st, LONGBI INDUSTRIAL PARK，BANTIAN VILLAGE, BUJI TOWN，SHENZHEN, GUANG DONG PROVIDENCE, CHINA Product Designation AD701-KRECEIVER Brand Name N/A Test Model AD701-K Test Standard OET Bulletin 65 (Edition 97-01) Supplement C (Edition 01-01) File Number: AGC20M120302-2F7 Date of Test: May 04, 2012 to May 07, 2012 We (AGC), Attestation of Global Compliance Co., Ltd. for compliance with the requirements set forth in the FCC Standard OET Bulletin 65 (Edition 97-01) Supplement C (Edition 01-01) The results of testing in this report apply to the product/system which was tested only. Tested By: Curoky Chen May 08, 2012 Reviewed By Forrest Lei May 08, 2012 Approved By Solger Zhang May 08, 2012 Report No.: AGC20M120302-2F7 Page 3 of 7 2. TECHNICAL INFORMATION Note: the following data is based on the information by the applicant. 2.1 EUT DESCRIPTION Operation Frequency 2408.95 MHz to 2474.23 MHz Rated Output Power 15.43dBm(max) Hardware Version V1.0 Software Version V1.0 Modulation GFSK Number of channels 24 Antenna Designation Detachable Antenna Gain 1.8dBi Power Supply DC 5V by adapter Note: 1. For more details, please refer to the User’s manual of the EUT. Report No.: AGC20M120302-2F7 Page 4 of 7 3. RF EXPOSURE MEASUREMENT 3.1 INTRODUCTION Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. The 1992 ANSI/IEEE standard (See Listed limit table) specifies a minimum separation distance of 20 cm for performing reliable field measurements to determine adherence to MPE limits. If the minimum separation distance between a transmitter and nearby persons is more than 20 cm under normal operating conditions, compliance with MPE limits may be determined at such distance from the transmitter. When applicable, operation instructions and prominent warning labels may be used to alert the exposed persons to maintain a specified distance from the transmitter or to limit their exposure durations and usage conditions to ensure compliance. Report No.: AGC20M120302-2F7 Page 5 of 7 3.2 FCC LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f=Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirements for mobile and portable transmitters. Report No.: AGC20M120302-2F7 Page 6 of 7 4. CLASSIFICATION OF THE ASSESSMENT METHODS According to user manual,The antenna of the product, under normal use condition is at least 0.25m away from the body of the user. Warning statement to the user for keeping at least 25cm separation distance and the prohibition of operating to a person has been printed on the user’smanual. So, this product under normal use is located on electromagnetic far field betweenthe human body. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 5. EUT OPERATION CONDITION Make the EUT to transmit at lowest, middle and highest channel individually. Report No.: AGC20M120302-2F7 Page 7 of 7 6. TEST RESULTS Antenna Gain=1.8dBi(Numeric 1.514), ∏=3.1416 Channel Output Power Output Power Power Density Power Density Limit Result dBm mW mW/cm2 mW/cm2 Pass/Fail CH 00 14.71 29.58 0.006 1 Pass CH 12 14.93 31.12 0.006 1 …

Text truncated - open the document above for the full version.

FCC LINE CONDUCTED EMISSION TEST SETUP FCC RADIATED EMISSION TEST SETUP