T8C103Remote Control Transmitter

US Telecody Keypad Transmitter WARNING There is a possible risk of injury or death if safety instructions will not be observed. Please read and follow all instructions in this manual as well as the information for each receiver you are planning to operate with this device. Please share this important information with other users. No modifications to this device are permissible. Modifications performed to this device other than described in this manual or granted by the manufacturer, will result in the loss of the operating license. This device complies with FCC rules part 15. The operation of this device is subject to the following conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Use only original equipment manufacturer (OEM) parts and accessories as well as fixing supplies. Do not expose this device to a power pressure washer or to a water hose as water may penetrate into the interior and damage or destroy this device. Serial number label On the outside of the Telecody – Keypad is a label which indicates the serial number. The factory preprogrammed access codes (see chapter “programming access codes”) can only be deleted by using this serial number. Otherwise the transmitter needs to be returned to the factory for the deletion of these access codes. ►Attach this label in a secure location for example: your address book or the controller housing of your operator. Operation The transmitter sends a signal to a receiver i.e. the garage door opener which will result in an opening and closing of the garage door. To prevent unwanted operation of the keypad it is advisable to program access codes to the transmitter. The Telecody – Keypad was developed for the exterior operation. Simply use the included holder and attach to either a wall or to the garage door frame if available. Technical data P E M C S P E M C S 5-13/16” 1-7/8” 1-3/16” Frequency 310 MHz Operational temperature –5°F to +130°F (–20 °C to +55 °C) Range Approx. 80 ft (24 m) (depending on surroundings) IP Rating IP 64 Battery (included) Lithium CR 123 A, 3 Volt Dimensions (incl. holder) Height: 5-13/16“ (147 mm) Width: 1-7/8“ (48 mm) Depth: 1-3/16“ (30 mm) Weight (incl. battery and holder) Approx. 6.4 oz (180 g) Radio codes 12 different codes (10 codes with programmable access codes and 2 without) Scope of delivery Please check package contents. In case something is missing, please contact your dealer who will be happy to assist. Please do dispose packaging according to your local waste regulations. P E M C S P E M C S 3 2 6 7 45 1 1) Transmitter assembled 2) Battery (already inserted) 3) Holder (attach to either a wall or to the garage door frame if available) 4) 2 screws to mount the holder 5) 2 anchors 3/16“ (Ø 6 mm) 6) 1 screw to attach the transmitter to the holder 7) 1 installation and operating manual Required tools 56 123 7 4 Ø3/16" 1) Hammer Drill 2) Drill bit for masonry 3) Phillips screwdriver (medium) 4) Hammer 5) Measuring/Tape 6) Level 7) Pencil Installation and installation requirements WARNING There is a possible risk of injury or death if safety instructions will not be observed. The transmitter shall only be installed if the following installation requirements are given. For the installation, choose an easy accessible location within the transmitter range. The distance from the ground needs to be at least 5‘ (1.50 meter) to prevent that children could play with the transmitter. Mount the holder on a flat surface. To control a door opener or gate operator with the transmitter, please select the installation location as follows: –away from the door and the operator mechanics –whoever is using the device, needs to have a clear view to the garage door –that the user will be able to be outside of the door and the operator mechanics while using the transmitter. Installation The transmitter incl. the holder can be mounted by using the included fixing supplies to either wood or brick. P E M C S 1 2 ►Remove the cover (1) and slide the transmitter out of the holder. 1-15/16” Ø3/16 ►Mark two mounting point in a distance of 1-15/16“ (50 mm) apart in a vertical line. WARNING There is a risk of injury from flying chips when drilling. Drill chips could get into the eyes and cause injury to the eyes. Make sure to always wear safety glasses when drilling. ►Drill two holes by using a masonry drill bit 3/16“ (Ø 6 mm) and insert two anchors 3/16“ Ø 6 mm) into the holes. ►Mount the actual holder by using two screws to the wall. P E M C S P E M C S WARNING When sliding the transmitter back into the holder, there is a possible risk of squeezing or abrasion to the hand. ►Slide the transmitter carefully from the top into the holder until it stops. ►Attach the transmitter with a screw (1) and clip the cover (2) onto the transmitter. Function of buttons 0-9 (a-z) – digits- (letters) keys –Sending command 1) –Enter access code 2) ESC – Cancel- /Delete button –Active time 3) –Cancel the command P – Programming button –Change access code –Reset device back to factory settings (in combination with the M-Button) M – Programming button –Remove locking of button –Turn on/off the active time –Reset device back to factory settings (in combination with the P-Button)  – Dot button –Send command without access code –Turn on keypad illumination  – Circle button –Send command without access code –Turn on keypad illumination 1) The transmitter sends a radio signal to a receiver i.e. the garage door operator which will result in opening and closing of the garage door. The transmitter has 12 radio commands, (0...9, 10 =>0, 11 , 12 => O) which can be transmitted by pressing one of the buttons. 2) The access code is an encrypted code. The transmitter will only send the command if the correct code is entered. 3) The active time is a time gap for transmitting the previous entered code again by using any of the digit-keys. LED Indi…

Text truncated - open the document above for the full version.

Sommer Antriebs- und Funktechnik GmbH Address: Hans-Böckler-Straße 21-27 D-73230 Kirchheim/Teck Phone: +49 (0)7021/ 8001-412 Fax: +49 (0)7021/ 8001-403 Manufacturer of radiocontrolled operators for garage doors with accessories Your ref. Your message from Our ref. baa Date 20.09.2012 page 1 of 1 Department : Entwicklung / (Development) / Badran, Ali E-Mail : [email protected] http://www.sommer.eu Sommer Antriebs- und Funktechnik GmbH, Hans-Böckler-Str. 21-27, D-73230 Kirchheim/Teck Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. SOMMER Antriebs- u. Funktechnik GmbH would like the following documents regarding this submission for FCC ID: T8C103 to be kept confidential: 04_BlkDia.pdf: Block diagram 05_OpDes.pdf: Operational description 06_Schem.pdf: Schematic The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, A. Badran

Type TX04-310-10 FCC ID T8C103 / IC: 6496A-103 Abteilung: Entwicklung / (Development) erstellt am: 27.09.2012 erstellt von: Badran, Ali Verteiler: Seite von 1 2 External Photos: Front view with Holder Front view without Holder Rear view with holder Type TX04-310-10 FCC ID T8C103 / IC: 6496A-103 Abteilung: Entwicklung / (Development) erstellt am: 27.09.2012 erstellt von: Badran, Ali Verteiler: Seite von 2 2 Rear view without holder The device identifier is engraved on the rear side of the device. Picture of the device identifier:

FCC ID: T8C103 Telephone: +49 9194 9016 Telefax: +49 9194 8125 Mail: [email protected] Web: http://www.emcc.de EMCCons DR. RAŠEK GmbH & Co. KG Moggast, Boelwiese 8 91320 Ebermannstadt Germany 950432.1W_Annex2 Page 1 of 4 ANNEX 2 TO TEST REPORT # EMCC-950432.1W, 2012-09-27 PHOTOGRAPHS OF EQUIPMENT UNDER TEST (EUT) EXTERNAL VIEWS EQUIPMENT UNDER TEST: Trade Name: US Telecody Keypad Transmitter Model: TX04-310-10 Serial Number: Sample #4 Equipment Category: Transmitter Manufacturer: SOMMER Antriebs- und Funktechnik GmbH Address: Hans-Boeckler-Strasse 21-27 73230 Kirchheim/Teck Germany Phone: +49 7021 8001-412 Fax: +49 7021 8001-403 E-mail: [email protected] RELEVANT STANDARD(S): 47 CFR Part 15C RSS-210 Issue 8 (2010-12) MEASUREMENT PROCEDURE USED: ANSI C63.4-2009 FCC/OET MP-4 (1987) Other CONTENTS Page 1 Front view w/ holder ............................................................................................................................................................................ 2 2 Rear view w/ holder .............................................................................................................................................................................. 2 3 Front view w/o holder .......................................................................................................................................................................... 3 4 Rear view w/o holder ........................................................................................................................................................................... 3 5 Rear close-up view (labeling) ............................................................................................................................................................. 4 FCC-ID: T8C103 Annex 2 to Test Report #EMCC-950432.1W Page 2 of 4 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex2 1 Front view w/ holder 2 Rear view w/ holder FCC-ID: T8C103 Annex 2 to Test Report #EMCC-950432.1W Page 3 of 4 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex2 3 Front view w/o holder 4 Rear view w/o holder Photograph as received from the manufacturer. FCC-ID: T8C103 Annex 2 to Test Report #EMCC-950432.1W Page 4 of 4 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex2 5 Rear close-up view (labeling)

Type TX45-310-10 FCC ID T8C104 / IC: 6496A-104 Abteilung: Entwicklung / (Development) erstellt am: 20.09.2012 erstellt von: Schwarz, Dominik Verteiler: Seite von 1 1 Device-Identifier: Device-Identifier location: The Device-Identifier is engraved on the rear side of the device:

Type TX04-310-10 FCC ID T8C103 / IC: 6496A-103 Abteilung: Entwicklung / (Development) erstellt am: 20.09.2012 erstellt von: Badran, Ali Verteiler: Seite von 1 3 Internal photos: PCB inside the housing PCB front view Type TX04-310-10 FCC ID T8C103 / IC: 6496A-103 Abteilung: Entwicklung / (Development) erstellt am: 20.09.2012 erstellt von: Badran, Ali Verteiler: Seite von 2 3 PCB rear view Type TX04-310-10 FCC ID T8C103 / IC: 6496A-103 Abteilung: Entwicklung / (Development) erstellt am: 20.09.2012 erstellt von: Badran, Ali Verteiler: Seite von 3 3 Rear view without holder The device identifier is engraved on the rear side of the device. Picture of the device identifier:

FCC ID: T8C103 Telephone: +49 9194 9016 Telefax: +49 9194 8125 Mail: [email protected] Web: http://www.emcc.de EMCCons DR. RAŠEK GmbH & Co. KG Moggast, Boelwiese 8 91320 Ebermannstadt Germany 950432.1W_Annex3 Page 1 of 3 ANNEX 3 TO TEST REPORT # EMCC-950432.1W, 2012-09-27 PHOTOGRAPHS OF EQUIPMENT UNDER TEST (EUT) INTERNAL VIEWS EQUIPMENT UNDER TEST: Trade Name: US Telecody Keypad Transmitter Model: TX04-310-10 Serial Number: Sample #4 Equipment Category: Transmitter Manufacturer: SOMMER Antriebs- und Funktechnik GmbH Address: Hans-Boeckler-Strasse 21-27 73230 Kirchheim/Teck Germany Phone: +49 7021 8001-412 Fax: +49 7021 8001-403 E-mail: [email protected] RELEVANT STANDARD(S): 47 CFR Part 15C RSS-210 Issue 8 (2010-12) MEASUREMENT PROCEDURE USED: ANSI C63.4-2009 FCC/OET MP-4 (1987) Other CONTENTS Page 1 EUT Parts .............................................................................................................................................................................................. 2 2 PCB side 1 ............................................................................................................................................................................................. 2 3 PCB side 2 ............................................................................................................................................................................................. 3 FCC-ID: T8C103 Annex 3 to Test Report #EMCC-950432.1W Page 2 of 3 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex3 1 EUT Parts (Remark: Holder not shown.) 2 PCB side 1 FCC-ID: T8C103 Annex 3 to Test Report #EMCC-950432.1W Page 3 of 3 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex3 3 PCB side 2

lurrcc- IÍ r*. nlSnx FCC lD: T8C103 Page 1 of29 TEST REPORT # EMCC-950432.1W, 2012-09-27 EQUIPMENT UNDER TEST: Trade Name: US Telecody Keypad Transmitter Model: TX04-310-10 Serial Number: Sample #4 Equipment Category: Transmitter Manufacturer: SOMMER Antriebs- und Funktechnik GmbH Address: Hans-Boeckler-Strasse 21-27 73230 Kirchheim/Teck Germany Phone: +497021 8001-412 Fax: +497021 8001-403 E-mail: [email protected] RELEVANT STANDARD(S): 47 CFR Part 15C RSS-210 lssue I (2010-12) MEASUREMENT PROCEDURE USED: X nrusl c63.4-2009 X nss-cen lssue 3 n otner TEST REPORT PREPARED BY: Wolfgang Döring EMCCONS DR. RASEK GMbH & CO. KG Moggast, Boelwiese I 91320 Ebermannstadt Germany Phone: +49 9194 9016 Fax: +49 91948125 E-mail: [email protected] TEST PERSONNEL: HEAD OF LABORATORY: Reinhard Sauerschell Wolfgang Döring EMCCons OR. NESEX GmbH & Co. KG Moggast, Boelwiese I 91320 Ebermannstadt Germany 9s0432.'1W EMC, Radio, Safety and Environmental Testing Telephone: +49 9194 9016 Telefax: +49 9194 8125 Mail: [email protected] Web: http://www.emcc.de ( ooo*t.,." Akkreditierungsstelle D-PL-12067-01-01 FCC-ID: T8C103 Test Report #EMCC-950432.1W Page 2 of 29 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W CONTENTS Page 1 GENERAL INFORMATION ................................................................................................................................................................... 3 1.1 Purpose .................................................................................................................................................................................. 3 1.2 Limits and Reservations ...................................................................................................................................................... 3 1.3 Test Location ......................................................................................................................................................................... 3 1.4 Manufacturer ......................................................................................................................................................................... 4 1.5 Dates ...................................................................................................................................................................................... 4 1.6 Ordering Information ............................................................................................................................................................ 4 1.7 Climatic Conditions .............................................................................................................................................................. 4 2 PRODUCT DESCRIPTION .................................................................................................................................................................... 5 2.1 Equipment Under Test (EUT) ............................................................................................................................................... 5 2.2 EUT Peripherals .................................................................................................................................................................... 5 2.3 Mode of Operation During Testing ..................................................................................................................................... 5 2.4 Modifications Required for Compliance ............................................................................................................................ 5 3 TEST RESULTS SUMMARY ................................................................................................................................................................ 6 4 ANTENNA REQUIREMENT .................................................................................................................................................................. 7 4.1 Regulation ............................................................................................................................................................................. 7 4.2 Result ..................................................................................................................................................................................... 7 5 CONDUCTED EMISSIONS TEST ......................................................................................................................................................... 8 5.1 Regulation ............................................................................................................................................................................. 8 5.2 Test Equipment ..................................................................................................................................................................... 8 5.3 Test Procedures .................................................................................................................................................................... 8 5.4 Test Results ........................................................................................................................................................................... 8 6 RADIATED EMISSIONS TESTS ........................................................................................................................................................... 9 6.1 Regulation ............................................................................................................................................................................. 9 6.2 Test Equipment .......................................................................................................................................................…

Text truncated - open the document above for the full version.

FCC ID: T8C103 Telephone: +49 9194 9016 Telefax: +49 9194 8125 Mail: [email protected] Web: http://www.emcc.de EMCCons DR. RAŠEK GmbH & Co. KG Moggast, Boelwiese 8 91320 Ebermannstadt Germany 950432.1W_Annex1 Page 1 of 5 ANNEX 1 TO TEST REPORT # EMCC-950432.1W, 2012-09-27 PHOTOGRAPHS OF TEST SETUPS EQUIPMENT UNDER TEST: Trade Name: US Telecody Keypad Transmitter Model: TX04-310-10 Serial Number: Sample #4 Equipment Category: Transmitter Manufacturer: SOMMER Antriebs- und Funktechnik GmbH Address: Hans-Boeckler-Strasse 21-27 73230 Kirchheim/Teck Germany Phone: +49 7021 8001-412 Fax: +49 7021 8001-403 E-mail: [email protected] RELEVANT STANDARD(S): 47 CFR Part 15C RSS-210 Issue 8 (2010-12) MEASUREMENT PROCEDURE USED: ANSI C63.4-2009 FCC/OET MP-4 (1987) Other CONTENTS Page 1 CONDUCTED EMISSIONS TEST ......................................................................................................................................................... 2 2 RADIATED EMISSIONS TEST ............................................................................................................................................................. 3 2.1 Magnetic field (H-field), f < 30 MHz, EUT w/o holder, vertical .......................................................................................... 3 2.2 Electric field, f = 30 MHz to 1 GHz, EUT w/o holder, horizontal ....................................................................................... 3 2.3 Electric field, f = 30 MHz to 1 GHz, EUT w/o holder, horizontal, upright ........................................................................ 4 2.4 Electric field, f > 1 GHz, EUT w/o holder, horizontal ......................................................................................................... 4 2.5 Electric field, f > 1 GHz, EUT w/ holder, vertical ................................................................................................................ 5 FCC-ID: T8C103 Annex 1 to Test Report #EMCC-950432.1W Page 2 of 5 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex1 1 CONDUCTED EMISSIONS TEST None. not applicable FCC-ID: T8C103 Annex 1 to Test Report #EMCC-950432.1W Page 3 of 5 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex1 2 RADIATED EMISSIONS TEST 2.1 Magnetic field (H-field), f < 30 MHz, EUT w/o holder, vertical 2.2 Electric field, f = 30 MHz to 1 GHz, EUT w/o holder, horizontal FCC-ID: T8C103 Annex 1 to Test Report #EMCC-950432.1W Page 4 of 5 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex1 2.3 Electric field, f = 30 MHz to 1 GHz, EUT w/o holder, horizontal, upright 2.4 Electric field, f > 1 GHz, EUT w/o holder, horizontal FCC-ID: T8C103 Annex 1 to Test Report #EMCC-950432.1W Page 5 of 5 Issue Date: 2012-09-27 Test of SOMMER US Telecody Keypad Transmitter Model TX04-310-10 to 47 CFR Part 15C and RSS-210 Issue 8 (2010-12) © EMCCons DR. RAŠEK GmbH & Co. KG 2012 950432.1W_Annex1 2.5 Electric field, f > 1 GHz, EUT w/ holder, vertical