TE6-DRWLS1273LDR-WLS1273L-102

Preliminary and RFM Confidential www.RFM.com Technical support +1.972.448.3700 Page 1 of 31 © 2012 by RF Monolithics, Inc. E-mail: [email protected] DR-WLS1273L-102 Data Sheet - 12/13/12 DR-WLS1273L-102 FCC/ETSI/IC Certified WLAN/Bluetooth Multifunction Module Data Sheet Preliminary and RFM Confidential www.RFM.com Technical support +1.972.448.3700 Page 2 of 31 © 2012 by RF Monolithics, Inc. E-mail: [email protected] DR-WLS1273L-102 Data Sheet - 12/13/12 Scope This specification applies to the IEEE802.11a/b/g/n WLAN and Bluetooth 4.0 standards. Interfaces WLAN: 4-bit SDIO Bluetooth: UART, PCM IC and Firmware WLAN/BT RF/BB/MAC IC: TI WL1273L PG 3.1 Front-end IC for WL1273L: TriQuint TQP6M9002 ES1.8 Clocks and Compliance Sleep Clock: External 32.768 kHz oscillator required RoHS: This module is compliant with the RoHS directive Bluetooth: Qualified Design Listing: B017989 Certifications FCC, ETSI and Industry Canada For mobile operating conditions (greater than 20 cm to the body) - This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For portable operating conditions (less than 20 cm to the body) - This equipment complies with FCC radi- ation exposure limits set forth for an uncontrolled environment. This equipment may operate in direct con- tact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Certification testing conducted with Antenna Factor ANT-RAF-RPS 2.4/5 GHz antenna, RSMA connector. Part Numbers Module: DR-WLS1273L-102 Preliminary and RFM Confidential www.RFM.com Technical support +1.972.448.3700 Page 3 of 31 © 2012 by RF Monolithics, Inc. E-mail: [email protected] DR-WLS1273L-102 Data Sheet - 12/13/12 Block Diagram 2.4 GHz WLAN/BT VBAT UART PCM SDIO Slow CLK DC-DC Converter 38.4 MHz Fast CLK Front End IC and RF Filtering 5.8 GHz WLAN WL1273L VIO DR-WLS1273L-102 WLAN Features • WLAN MAC baseband processor and RF transceiver which are IEEE802.11a/b/g and IEEE802.11n PICS compliant • Optimized for ultra-low current consumption in all operating modes • Accepts 19.2, 26, 38.4 or 52 MHz reference clock inputs for easy integration into cellular handsets, etc. • IEEE Standard 802.11d, e, h, i, k, r, PICS compliant • Support for Cisco Client eXtensions (CCX) standard • Serial debug interface • Support for Secure Digital Input/Output (SDIO) host interface • Medium Access Controller (MAC) – Embedded ARM™ central processing unit (CPU) – Hardware-based encryption/decryption using 64-, 128- or 256-Bit WEP, TKIP or AES keys – Supports Wi-Fi protected access (WPA and WPA2.0) and IEEE Standard 802.11i, including hardware accelerated Advanced Encryption Standard (AES) – Designed to work with IEEE Std 802.1x for Virtual Private Network (VPN) solutions Preliminary and RFM Confidential www.RFM.com Technical support +1.972.448.3700 Page 4 of 31 © 2012 by RF Monolithics, Inc. E-mail: [email protected] DR-WLS1273L-102 Data Sheet - 12/13/12 • Baseband Processor – IEEE Std 802.11n single-stream data rates (MCS0-7) and SGI support • 2.4/5.8 GHz Radio – Digital Radio Processor (DRP) implementation – Integrated LNA – Supports IEEE Std 802.11a/b/g and 802.11n DR-WLS1273L-102 Bluetooth Features • V4.0 + EDR, Power Class 1.5 + BLE • Bluetooth Qualified Design Listing: B017988 • BT Enhanced Data Rates - 2 and 3 Mbps • Enhanced UART host interface • Very low power consumption • On-chip Embedded radio – Integrated 2.4 GHz RF transceiver – All digital PLL transmitter with digitally controlled oscillator – Near-zero IF architecture – On-chip TX/RX switch – Support for Class-1.5 applications • Embedded ARM microprocessor system – High rate four wire UART HCI (H4) and three wire UART HCI (H5) – Automatic clock-detection mechanism • Flexible PCM interface - full flexibility for data order, sampling and positioning • Temperature detection and compensation mechanism ensures minimal variation in the RF performance over the entire operating temperature range • Low-power scan achieves paging and inquiry scans at 1/3 normal power • Digital Radio Processor (DRP) single-ended 50 ohm I/O for easy RF interfacing • Patch trap mechanism and reserved RAM enables easy bug fixes • Advance Audio Interfaces and capabilities – A2DP support – A2DP internal loopback – Wide-band speech support – On board SBC encoder/decoder - offloads host for A2DP and wide-band speech processing – Full support for Bluetooth low energy (BLE) standard. BLE can operate in parallel with standard Bluetooth function. WLAN Functional Blocks The DR-WLS1273L-102 WLAN architecture includes a digital radio processor and a point-to-multipoint baseband core function. The architecture is based on a single-processor ARM core. The device includes on-chip peripherals to enable easy communication between a host system and the WLAN core function. Preliminary and RFM Confidential www.RFM.com Technical support +1.972.448.3700 Page 5 of 31 © 2012 by RF Monolithics, Inc. E-mail: [email protected] DR-WLS1273L-102 Data Sheet - 12/13/12 WLAN SDIO Transport Layer SDIO is the WLAN host interface in the DR-WLS1273L-102. This interface is a standard SDIO interface (SDIO spec Version 2.0). The DR-WLS1273L-102 SDIO also supports the following features: • 4-bit data bus • Functions number 0 and 2 • Multi-Block data transfer • The SDIO interface is used for WLAN. The WLAN block uses function 2. Function 0 is used for the common I/O area. WLAN MAC The DR-WLS1273L-102 MAC implements the IEEE standard 802.11 MAC sub-layer using both dedicated hardware and embedded firmware. The MAC hardware implements real-time functions, including access protocol management, encryption and decryption. WLAN Baseband Processor The DR-W…

Text truncated - open the document above for the full version.

WLS1273L

§ 15.247(i) Maximum Permissible Exposure RF Exposure Requirements: §1.1307(b)(1) and §1.1307(b)(2): Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. RF Radiation Exposure Limit: §1.1310: As specified in this section, the Maximum Permissible Exposure (MPE) Limit shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in Sec. 1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of Sec. 2.1093 of this chapter. MPE Limit Calculation: EUT’s operating frequencies @ 2400-2483.5 MHz; highest conducted power = 22.75dBm (peak) therefore, Limit for Uncontrolled exposure: 1 mW/cm 2 or 10 W/m 2 EUT maximum antenna gain = 3 dBi. Equation from page 18 of OET 65, Edition 97-01 S = PG / 4R 2 or R = √PG / 4S where, S = Power Density (1 mW/cm 2 ) P = Power Input to antenna (188.36mW) G = Antenna Gain (2.00 numeric) S = (188.36*2.00/ 4*3.14*20.0 2 )= (375.84 / 5024) = 0.075 mW/cm 2 @ 20cm separation

SYS CLOCK LTR C BACD 654321 DATE: DBA ECO NO: APPROVED: REVISION RECORD SCALE: SHEET: OF DRAWING NO: TITLE:COMPANY: RELEASED: DATED: DATED: QUALITY CONTROL:CHECKED: DATED: DATED: DRAWN: CODE: SIZE: REV: 1 1 A 454-1273-503 B Schematic, DR-WLS1273L-102 RF Monolithics 21may12 Patrick Evans A. PWE . 38.4 MHz 1 VC/NC 2 GND 3 OUT 4 VCC Y1 XTC7012 C327 C147 123456789 1011121314151617181920212223242526 2728293031323334353637383940414243444546474849505152 BOARD_EDGE PINS 2 & 3 TIE TO GND PIN 1 IS RF IO 1 23 J1 U.FL-R C2 .01uF C4.01 1 GND1 2 5G_ANT 3 GND3 4 HOST_WAKE 5 CLK_REQ 6 GND6 7 1V8_PRE_REG 8 VDD_LDO_IN_CLASS1P5 9 VBAT 10 VIO 11 GND11 12 BT_RESETX 13 WLAN_IRQ 14 FM_EN 15 WL_RS232_TX 16 WL_RS232_RX 17 WLANENABLE 18 GND18 19 SDIO_D2 20 SDIO_D1 21 SPI_CSX 22 SPI_DIN 23 SPI_CLK 24 SPI_DOUT 25 GND25 26 SLEEP_CLK 27 GND27 28 FM_TX_ANT 29 GND29 30 FM_RX_ANT 31 GND31 32 GND32 33 FM_AUD_IN_R 34 FM_AUD_IN_L 35 FM_AUD_OUT_R 36 FM_AUD_OUT_L 37 GND37 38 XTALP 39 XTALM 40 GND40 41 BT_WAKEUP 42 UART_TX 43 UART_CTS 44 UART_RX 45 UART_RTS 46 GND46 47 2.4G_ANT 48 GND48 49 GND49 50 GND50 51 PCM_SYNC 52 PCM_CLK 53 PCM_OUT 54 PCM_IN 55 FM_I2S_DO 56 FM_I2S_DI 57 FM_I2S_FYNC 58 FM_I2S_CLK 59 GND59 60 GND60 61 FM_SCL 62 FM_IRQ 63 FM_SDA 64 UART_DBG 65 BT_UART_DBG 66 GND66 67 GND67 68 GND68 69 GND69 70 GND70 71 GND71 72 GND72 73 GND73 74 GND74 U1 PINS 2 & 3 TIE TO GND PIN 1 IS RF IO 1 23 J2 U.FL-R A1 GND A2 EN B1 VOUT B2 VIN U2 LD6806 C51uF C61uF VCLK HOST_WAKE UART_DBG WLAN_IRQ BT_EN WLAN_RX WLAN_TX WLAN_EN SDIO_D3 SDIO_D2SDIO_D1 SDIO_DO SDIO_CMD SDIO_CLK PCM_SYNC BT_RXBT_RTSBT_TX PCM_CLK PCM_OUT BT_CTS PCM_IN BT_WAKEBT_UARTD5GHZ_ANT PCM_OUT PCM_IN HOST_WAKE BT_EN WLAN_IRQ WLAN_TX WLAN_RX WLAN_EN SDIO_D2 SDIO_D1 SDIO_CMD SDIO_CLK SDIO_DO SDIO_D3 BT_WAKE VIO VBAT BT_CTSBT_RTS BT_TX BT_RX PCM_SYNC PCM_CLK BT_UARTD UART_DBG 2.4GHZ_ANT INT_CLK_REQ SLEEP_CLK SLEEP_CLK VIO 5GHZ_ANT 2.4GHZ_ANT VBAT VIO VBATVCLK INT_CLK_REQ

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE ! BALTIMORE, MARYLAND 21230-3432 ! PHONE (410) 354-3300 ! FAX (410) 354-3313 33439 WESTERN AVENUE ! UNION CITY, CALIFORNIA 94587 ! PHONE (510) 489-6300 ! FAX (510) 489-6372 3162 BELICK STREET ! SANTA CLARA, CA 95054 ! PHONE (408) 748-3585 ! FAX (510) 489-6372 13301 MCCALLEN PASS ! AUSTIN, TX 78753 ! PHONE (512) 287-2500 ! FAX (512) 287-2513 The Nation’s First Licensed Nationally Recognized Testing Laboratory December 5, 2012 Murata Wireless 4441 Sigma Road Dallas, TX 75244 Dear Bob Nelson, Enclosed is the EMC Wireless test report for compliance testing of the Murata Wireless, DR-WLS1273L-102 as tested to the requirements of Title 47 of the CFR, Ch. 1 (10-1-06 ed.), Part 15, Subpart B and ICES-003, Issue 5 August 2012 for a Class B Digital Device, and FCC Part 15 Subpart C and RSS-210, Issue 8, Dec. 2010 for Intentional Radiators. Thank you for using the services of MET Laboratories, Inc. If you have any questions regarding these results or if MET can be of further service to you, please feel free to contact me. Sincerely yours, MET LABORATORIES, INC. Jennifer Warnell Documentation Department Reference: (\Murata Wireless\EMCS36587A-FCC247) Certificates and reports shall not be reproduced except in full, without the written permission of MET Laboratories, Inc. Electromagnetic Compatibility Murata Wireless Cover Page DR-WLS1273L-102 CFR Title 47, Part 15B, 15.247; RSS-210, Issue 8, Dec. 2010 & ICES-003 MET Report: EMCS36587A-FCC247 © 2012, MET Laboratories, Inc. Page ii of ix DOC-EMC702 6/18/2009 Electromagnetic Compatibility Criteria Test Report for the Murata Wireless DR-WLS1273L-102 Tested under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B & ICES-003 for Class B Digital Devices & 15.247 Subpart C & RSS-210, Issue 8, Dec. 2010 for Intentional Radiators MET Report: EMCS36587A-FCC247 December 5, 2012 Prepared For: Murata Wireless 4441 Sigma Road Dallas, TX 75244 Prepared By: MET Laboratories, Inc. 914 W. Patapsco Ave. Baltimore, MD 21230 Electromagnetic Compatibility Murata Wireless Cover Page DR-WLS1273L-102 CFR Title 47, Part 15B, 15.247; RSS-210, Issue 8, Dec. 2010 & ICES-003 MET Report: EMCS36587A-FCC247 © 2012, MET Laboratories, Inc. Page iii of ix DOC-EMC702 6/18/2009 Electromagnetic Compatibility Criteria Test Report for the Murata Wireless DR-WLS1273L-102 Tested under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B & ICES-003 for Class B Digital Devices & 15.247 Subpart C & RSS-210, Issue 8, Dec. 2010 for Intentional Radiators Anderson Soungpanya, Project Engineer Jennifer Warnell Electromagnetic Compatibility Lab Documentation Department Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of the FCC Rules Parts 15B, 15.247 and Industry Canada standards ICES-003, Issue 5 August 2012, RSS-210, Issue 8, Dec. 2010 under normal use and maintenance. Dusmantha Tennakoon, Wireless Manager, Electromagnetic Compatibility Lab Electromagnetic Compatibility Murata Wireless Report Status DR-WLS1273L-102 CFR Title 47, Part 15B, 15.247; RSS-210, Issue 8, Dec. 2010 & ICES-003 MET Report: EMCS36587A-FCC247 © 2012, MET Laboratories, Inc. Page iv of ix DOC-EMC702 6/18/2009 Report Status Sheet Revision Report Date Reason for Revision  December 5, 2012 Initial Issue. Electromagnetic Compatibility Murata Wireless Table of Contents DR-WLS1273L-102 CFR Title 47, Part 15B, 15.247; RSS-210, Issue 8, Dec. 2010 & ICES-003 MET Report: EMCS36587A-FCC247 © 2012, MET Laboratories, Inc. Page v of ix DOC-EMC702 6/18/2009 Table of Contents I. Executive Summary .................................................................................................................................................1 A. Purpose of Test ...................................................................................................................................................2 B. Executive Summary ............................................................................................................................................2 II. Equipment Configuration .......................................................................................................................................3 A. Overview .............................................................................................................................................................4 B. References ...........................................................................................................................................................5 C. Test Site ..............................................................................................................................................................5 D. Description of Test Sample .................................................................................................................................6 E. Equipment Configuration ....................................................................................................................................8 F. Support Equipment .............................................................................................................................................8 G. Ports and Cabling Information ............................................................................................................................8 H. Mode of Operation ...............................................................…

Text truncated - open the document above for the full version.

Photograph 1. Conducted Emissions, Test Setup Photograph 2. Conducted Emissions, Test Setup, Side View Photograph 3. Radiated Emissions, Test Setup Photograph 4. Radiated Emissions, Test Setup, 30 MHz – 1 GHz Photograph 5. Radiated Emissions, Test Setup, Rear View Photograph 6. Conducted Emissions, 15.207(a), Test Setup Photograph 7. Conducted Emissions, 15.207(a), Test Setup, Side View Photograph 8. Radiated Spurious Emissions, Test Setup Photograph 9. Radiated Spurious Emissions, Test Setup 30MHz – 1GHz Photograph 10. Radiated Spurious Emissions, Test Setup above 1 GHz (1 Meter Distance for Radiated Spurious) Photograph 11. Radiated Spurious Emissions, Test Setup above 1 GHz (3 Meter Distance for Radiated Band Edge)