TETLKSPOT1LooK SPOT

LooK SPOT reader user’s guide For Use Under the Emergency Use Authorization (EUA) Only For in vitro Use Only For use with nasal swab specimens Rx Only INTENDED USE LooK SPOT is a smartphone-based reader to detect the COVID-19 antigen using LooK COVID-19 antigen cassette based on lateral flow immunoassay. LooK SPOT and LooK COVID-19 antigen cassettes use the qualitative detection of nucleocapsid protein antigen from SARS-CoV-2 in nasal swabs from patients suspected of COVID-19 within the first seven (7) days of symptom onset. The reagent is used to detect the SARS-CoV-2 nucleocapsid protein antigen, which is usually present in the respiratory tract specimens in the acute phase of infection. The test result is obtained by inserting the LooK COVID-19 antigen cassette into the smartphone-based LooK SPOT reader. When a positive result is presented, it means that there are viral antigens in the specimen, but the patient's medical history must be combined with other clinical data to assess the infection status; a positive result cannot exclude bacterial infection or co-infection with other viruses, and the detected pathogen may not be the main reason of the disease. Negative results cannot completely rule out SARS-CoV-2 infection, so this product should not be used as the only basis for treatment or management decisions (including infection control); negative results should be comprehensively evaluated based on the patient's contact history, medical history, signs and clinical symptoms, necessary at times, molecular diagnosis (RT-PCR) is used to confirm the diagnosis and serve as a basis for patient management. The LooK COVID-19 antigen cassette does not differentiate between SARS- CoV and SARS-CoV- 2. LooK COVID-19 antigen rapid test is for use at the Point of Care (POC) settings by medical or trained professionals who perform rapid lateral flow tests. It is only for use under the Food and Drug Administration's Emergency Use Authorization. SUMMARY The SARS-CoV-2 virus is a positive-stranded single-stranded RNA virus with an envelope with a virus particle diameter of about 50～200nm; it is composed of four main structural proteins: spike protein (S), envelope protein (E), membrane protein (M) and nucleocapsid protein (N). The nucleocapsid protein binds to the viral RNA, and the other three proteins together form the viral coat. Its gene sequence is similar to SARS and MERS viruses, but they belong to different species. The incubation period of the SARS-CoV-2 is about 2-14 days on average; most patients will have respiratory symptoms. Typical symptoms include frequent fever, dry cough, weakness of limbs, etc. (may be accompanied by muscle pain, diarrhea, sore throat, loss of smell and abdominal pain, etc.). There is a percentage of carriers without any clinical symptoms. Severe patients may develop acute respiratory distress syndrome (ARDS), septic shock, diffuse alveolar injury, or even death. SARS-CoV-2 virus has spread globally. LooK COVID-19 antigen rapid test is an immunochromatographic test that uses monoclonal antibodies combined with latex particles to detect whether there are SARS-CoV-2 antigens in nasal secretions. This reagent is not only easy to execute, and the test result can be ready within five (5) minutes with the use of LooK SPOT reader and a smartphone with LooK SPOT app. TEST PRINCIPLE LooK COVID-19 antigen immunochromatographic detection reagent uses a rapid immunochromatographic detection method to detect whether the nucleocapsid protein antigen of the SARS-CoV-2 virus is present in the nasal swab samples using specific monoclonal antibodies. LooK COVID-19 antigen cassette reagent is designed to detect whether patients who are suspected of being infected by SARS-CoV-2 virus have the SARS-CoV-2 antigen in their nasal swabs. Before performing the test, the patient has to download and register the LooK PASS app from the app stores. The patient scans the QR code of the LooK COVID-19 antigen cassette with the LooK PASS app, and the information is uploaded to the LocationNow AI Cloud for the registration of the test. Each LooK COVID-19 antigen cassette has an embedded microchip for security, quality control, and identification purposes. To perform the test, a nasal swab specimen is collected from the patient. Place the nasal swab into the Extraction Buffer Tube. Stir the nasal swab in the Extraction Buffer Tube for one (1) minute. The virus particles in the sample are disrupted and exposing the internal viral nucleoproteins. After disruption, use the dropper to extract the solution inside the tube and apply three drops in the sample window of the LooK COVID-19 antigen cassette. The sample migrates through the antigen cassette containing unique chemical environments. If SARS-CoV-2 viral antigen is present, they will be trapped in a specific location on the test window of the antigen cassette. Insert the LooK COVID-19 antigen cassette into the LooK SPOT reader attached to a smartphone. LooK SPOT reader sends the images of the fluorescent signal in the test window of the cassette to LocationNow AI Cloud for analysis. LocationNow AI Cloud analyzes the images using proprietary AI algorithms and sends the test results to LooK SPOT app at 5 minutes. The test result can be Positive, Negative, or Invalid. The same test result is also sent to the patient's LooK PASS app. If the test result is negative, LooK PASS app will generate a QR code as Day Pass with a timestamp of the test for the patient. LocationNow AI algorithm provides high repeatability of detection vs. visual interpretation traditional methods in which human errors can occur from time to time. MATERIALS SUPPLIED 1. LooK SPOT Reader 2. Calibration Cassette 3. Double Side Adhesive Strip MATERIALS REQUIRED BUT NOT SUPPLIED 1. LooK COVID-19 Antigen Cassettes 2. Droppers 3. Extraction Buffer Tubes 4. Nasal swabs 5. AAA x 2 Batteries 6. Personal Protective Equipment WARNINGS AND PRECAUTIONS 1. For in vitro diagnostic use. 2. Do not u…

Text truncated - open the document above for the full version.

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Laipac Technology Inc. Address 20 Mural St. Unit 5 Richmond Hill Ontario L4B 1K3 Canada Grantee Code TET FCC ID TETLKSPOT1 Authorized Contact Name Diego Lai Contact Email [email protected] Contact Phone 905-7621228 I, the undersigne d, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and b e lief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations ma de in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this a pplication, (2) compliance statement labeling pur suant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensu re that production u nits of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the res ponsible party and ag ree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accept s and agrees to a bide by the post market surveillanc e requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testi ng. (2)the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3)the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SG S, FCC an d/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SG S. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and con ditions. Link to CFRs: htt ps://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signat ure: Date:November 4, 2020 Print Name: Diego Lai Title: CEO *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Laipac Technology Inc. Locate to protect 20 Mural St. Unit 5 Richmond Hill Ontario L4B 1K3 Canada Tel: 905-7621228 Fax: 905-7631737 E-mail: [email protected] http://www.laipac.com Date: November 4, 2020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding FCC ID: TETLKSPOT1 To whom it may concern: We, the undersigned, hereby authorize Kevin Tsai / Deputy Manager of Compliance Certification Services Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Laipac Technology Inc. This authorization is valid until further written notice from the applicant. Yours faithfully, Richmond Hill, Ontario Nov. 04 2020 _____________________________________________ ___________________________________ Signature Place and Date Diego Lai / CEO _____________________________________________ Name / Title

Laipac Technology Inc. Locate to protect 20 Mural St. Unit 5 Richmond Hill Ontario L4B 1K3 Canada Tel: 905-7621228 Fax: 905-7631737 E-mail: [email protected] http://www.laipac.com Date: November 4, 2020 To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Universal Electronics Inc. 201 East Sandpointe Ave 7th Floor Santa Ana CA 92707 USA Regarding: Confidentiality Request regarding application for FCC ID: TETLKSPOT1 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Richmond Hill, Ontario Nov.04 2020 _____________________________________________ ___________________________________ Signature Place and Date Diego Lai / CEO _____________________________________________ Name / Title

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 1 / 11 Report No.: T200910W02 Rev.: 00 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 11 Report No.: T200910W02 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 11 Report No.: T200910W02 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 11 Report No.: T200910W02 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 5 / 11 Report No.: T200910W02 Rev.: 00 Battery

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 6 / 11 Report No.: T200910W02 Rev.: 00 INTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 7 / 11 Report No.: T200910W02 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 8 / 11 Report No.: T200910W02 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 9 / 11 Report No.: T200910W02 Rev.: 00 BLE RF IC & Crystal BLE Antenna This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 10 / 11 Report No.: T200910W02 Rev.: 00 NFC RF IC NFC Crystal This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 11 / 11 Report No.: T200910W02 Rev.: 00 NFC Antenna

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 FCC ID: TETLKSPOT1 IC: 11280A-LOOKSPOT1 Page: 1 / 2 Report No.: T200910W02-MF Rev.: 00 APPENDIX 2 - RF EXPOSURE 1 FCC STANDARD APPLICABLE 1.1. FCC STANDARD APPLICABLE: According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. As per KDB 447498 D01 4.3.1, Step a: For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g Head & Body SAR and ≤ 7.5 for 10-g extremity Hand SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison  The values 3.0 and 7.5 are referred to as numeric thresholds in step b) below 1.2. MEASUREMENT RESULT: As the result of calculation result indicates, the RF exposure generating from given transmitter (transmitter employed digital modulation) can be excluded from SAR measurement, and is deemed compliant with RF exposure as per FCC. Step a: This is portable device and the max. output power including tune-up tolerance is 1.585 (mW), lower than the threshold given and derived as formula given above, where Freq. (MHz) Max. output power including tune-up tolerance (dBm) Max Conducted Output Power (mW) Distance (mm) Result 248021.58550.499 = 1.585 (mW) / 5 (mm) * √2.480 (GHz) = 0.499 <3.0 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 FCC ID: TETLKSPOT1 IC: 11280A-LOOKSPOT1 Page: 2 / 2 Report No.: T200910W02-MF Rev.: 00 2 ISED STANDARD APPLICABLE: 2.1. ISED STANDARD APPLICABLE As per RSS-102 Issue 5 March 19, 2015, any transmitter shall be compliant with applicable RF exposure prior to being market. In §2.5.1, SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance defined in Table 1. Output power level shall be the higher of the maximum conducted or equivalent isotropically radiated power (e.i.r.p.) source-based, time-averaged output power. 2.2. MEASUREMENT RESULT: Freq. (MHz) Max. output power including tune-up Peak Gain (dBi) Max Conducted Output Power (mW) e.i.r.p (mW) Exemption Limit (mW) 248020.51.5851.7784 Measurement Result: The e.i.r.p is 1.778mW when the device operates at the separation distance below or equals to 5mm. It is below the SAR exemption limit 4mW. Note: 1. The tune up power referred the AVG power of the test report T200910W02-RP for SAR test exclusion purpose.

FCC ID: TETLKSPOT1 IC: 11280A-LOOKSPOT1 Page: 1 / 31 Report No.: T200910W02-RP2 Rev.: 02 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group FCC 47 CFR PART 15 SUBPART C & INDUSTRY CANADA RSS-210 TEST REPORT For LooK SPOT Model No.: LooK SPOT I Trade Name: LooK SPOT Issued to Laipac Technology Inc. FCC: 20 Mural St. Unit 5 Richmond Hill Ontario L4B 1K3 Canada IC: 20 Mural St. Unit 5 Richmond Hill ON L4B 1K3 Canada Issued by Compliance Certification Services Inc. Wugu Laboratory No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. (R.O.C.) Issued Date: November 13, 2020 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 31 Report No.: T200910W02-RP2 Rev.: 02 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 November 6, 2020 Initial Issue ALL Allison Chen 01 November 13, 2020 See the following note Rev.(01) P.5, P.12, P.14 Allison Chen 02 November 13, 2020 See the following note Rev.(02) P.14 Allison Chen Rev.(01) 1. Added EUT serial number. 2. Added ISED CAB number in section 6.1. 3. Modify the RBW and VBW in test procedure in section 8.1. Rev.(02) 1. Modify the RBW and VBW in test procedure in section 8.1. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 31 Report No.: T200910W02-RP2 Rev.: 02 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ....................................................................................4 2. EUT DESCRIPTION ........................................................................................................5 3. TEST METHODOLOGY ..................................................................................................6 3.1 EUT CONFIGURATION ..........................................................................................6 3.2 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ................................6 3.3 RSS GEN SECTION 8.10 RESTRICTED BANDS OF OPERATIONS .....................7 3.4 DESCRIPTION OF TEST MODES ..........................................................................8 4. TEST SUMMARY ............................................................................................................9 5. INSTRUMENT CALIBRATION ...................................................................................... 10 5.1 MEASURING INSTRUMENT CALIBRATION ........................................................ 10 5.2 MEASUREMENT EQUIPMENT USED.................................................................. 10 5.3 MEASUREMENT UNCERTAINTY ........................................................................ 11 6. FACILITIES AND ACCREDITATIONS .......................................................................... 12 6.1 FACILITIES ........................................................................................................... 12 6.2 EQUIPMENT ......................................................................................................... 12 7. SETUP OF EQUIPMENT UNDER TEST ....................................................................... 13 7.1 SETUP CONFIGURATION OF EUT ..................................................................... 13 7.2 SUPPORT EQUIPMENT ....................................................................................... 13 8. FCC PART 15.225 REQUIREMENTS & RSS-210 REQUIREMENTS ........................... 14 8.1 OCCUPIED BANDWIDTH(99%) AND 20 DB BANDWIDTH .................................. 14 8.2 RADIATED EMISSIONS ....................................................................................... 16 8.3 FREQUENCY STABILITY ..................................................................................... 28 8.4 POWERLINE CONDUCTED EMISSIONS ............................................................ 30 APPENDIX A PHOTOGRAPHS OF TEST SETUP ........................................................... A-1 APPENDIX 1 - PHOTOGRAPHS OF EUT APPENDIX 2 - RF EXPOSURE This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 31 Report No.: T200910W02-RP2 Rev.: 02 1. TEST RESULT CERTIFICATION FCC Applicant: Laipac Technology Inc. 20 Mural St. Unit 5 Richmond Hill Ontario L4B 1K3 Canada IC Applicant: Laipac Technology Inc. 20 Mural St. Unit 5 Richmond Hill ON L4B 1K3 Canada Manufacturer: Laipac Technology Inc. 20 Mural St. Unit 5 Richmond Hill Ontario L4B 1K3 Canada Equipment Unde…

Text truncated - open the document above for the full version.

FCC ID: TETLKSPOT1 IC: 11280A-LOOKSPOT1 Page: 1 / 44 Report No.: T200910W02-RP1 Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group RADIO TEST REPORT FCC 47 CFR PART 15 SUBPART C Test Standard FCC Part 15.247 RSS-247 issue 2 and RSS-GEN issue 5 Product name LooK SPOT Brand Name LooK SPOT Model No. LooK SPOT I Test Result Pass Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. The test Result was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were given in ANSI C63.10: 2013 and compliance standards. The test results of this report relate only to the tested sample (EUT) identified in this report. The test Report of full or partial shall not copy. Without written approval of Compliance Certification Services Inc. (Wugu Laboratory) Approved by: Tested by: Kevin Tsai Dally Hong Deputy Manager Sr. Engineer This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 44 Report No.: T200910W02-RP1 Rev.: 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 November 6, 2020 Initial Issue ALL Allison Chen 01 November 13, 2020 See the following note Rev.(01) P.5, P.7, P.20 Allison Chen Rev. (01) 1. Modify antenna gain and EIRP power. 2. Added ISED CAB number in section 1.5. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 44 Report No.: T200910W02-RP1 Rev.: 01 Table of contents 1. GENERAL INFORMATION ........................................................................................ 4 1.1 EUT INFORMATION .................................................................................................. 4 1.2 EUT CHANNEL INFORMATION ................................................................................ 5 1.3 ANTENNA INFORMATION ........................................................................................ 5 1.4 MEASUREMENT UNCERTAINTY .............................................................................. 6 1.5 FACILITIES AND TEST LOCATION .......................................................................... 7 1.6 INSTRUMENT CALIBRATION ................................................................................... 7 1.7 SUPPORT AND EUT ACCESSORIES EQUIPMENT ................................................. 8 1.8 TEST METHODOLOGY AND APPLIED STANDARDS ............................................. 8 2. TEST SUMMARY ....................................................................................................... 9 3. DESCRIPTION OF TEST MODES............................................................................ 10 3.1 THE WORST MODE OF OPERATING CONDITION ................................................ 10 3.2 THE WORST MODE OF MEASUREMENT .............................................................. 11 3.3 EUT DUTY CYCLE ................................................................................................... 12 4. TEST RESULT ......................................................................................................... 13 4.1 AC POWER LINE CONDUCTED EMISSION ........................................................... 13 4.2 6DB BANDWIDTH AND OCCUPIED BANDWIDTH (99%) ...................................... 14 4.3 OUTPUT POWER MEASUREMENT ........................................................................ 18 4.4 POWER SPECTRAL DENSITY ................................................................................ 21 4.5 CONDUCTED BAND EDGE AND SPURIOUS EMISSION ...................................... 24 4.6 RADIATION BANDEDGE AND SPURIOUS EMISSION .......................................... 28 APPENDIX 1 - PHOTOGRAPHS OF EUT APPENDIX 2 - RF EXPOSURE This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 44 Report No.: T200910W02-RP1 Rev.: 01 1. GENERAL INFORMATION 1.1 EUT INFORMATION FCC Applicant / Manufacturer Laipac Technology Inc. 20 Mural St. Unit 5 Richmond Hill Ontario L4B 1K3 Canada IC Applicant / Manufacturer Laipac Technology Inc. 20 Mural St. Unit 5 Richmond Hill ON L4B 1K3 Canada Equipment LooK SPOT Model No. LooK SPOT I Model Discrepancy N/A Trade Name LooK SPOT Received Date September 10, 2020 Date of Test O…

Text truncated - open the document above for the full version.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-1 / A-2 Report No.: T200910W02-RP2 Rev.: 02 APPENDIX A PHOTOGRAPHS OF TEST SETUP CONDUCTED EMISSION SETUP PHOTOS This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-2 / A-2 Report No.: T200910W02-RP2 Rev.: 02 Radiated Emission Set up Photos 9kHz ~ 30MHz 30MHz ~ 1GHz

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-1 / A-2 Report No.: T200910W02-RP1 Rev.: 01 APPENDIX-A Test Photo Radiation (Below 1GHz) Radiation (Above 1GHz) This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-2 / A-2 Report No.: T200910W02-RP1 Rev.: 01 Conducted Emission Set up Photo