TLZ-CU640IEEE802.11 a/b/g/n/ac/ax and Bluetooth LE 5.4 LGA Module

DTS-UNII Declaration Letter Date: July 30, 2025 We have declared below featured for FCC equipment authorization, Device FCC ID: TLZ-CU640 (1) DFS Device -- Master, Client with Radar detection capability , Client without radar detection capability, N/A (2) Active / Passive Scanning , adhoc mode access point capability Frequency Band (MHz) Active Scanning (the device can transmit a probe (beacon)) Passive scanning (where the device is can listen only with no probes) Ad Hoc Mode capability Access point capability 2400 – 2483.5 Yes , No Yes , No Yes , No Yes , No 5150 - 5850 Yes , No Yes , No Yes , No Yes , No (3) Country code selection ability - Yes , No We don’t provide any controls or software to allow operation outside the USA frequency. (4) Meet 15.202 requirement - Yes , No , pls check below : A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. Sincerely, Applicant : AzureWave Technologies, Inc. Address : 8F., No. 94, Baozhong Rd., Xindian Dist., New Taipei City 23144, Taiwan Signature : _________________________________ Name and Job Title : Patrick Lin, Director E-mail : [email protected] Tel. : 02-55995599

Certification designating a U.S. Agent for service of process: As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. In either scenario, the designation of the U.S. agent for service of process should be provided as an attachment to the equipment authorization application. The applicant must provide a written certification, which must: i. Be signed by both the applicant and designated agent for service of process, if the agent is different from the applicant. ii. Acknowledge the applicant’s consent and the designated agent’s obligation to accept service of process. iii. Provide a physical U.S. address and email for the designated agent. iv. Acknowledge the applicant’s acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Unofficial information provided by FCC personnel on February 14, 2023, via the monthly call with the TCB Council: The Agent for Process of Service:  cannot be a TCB or affiliated with a TCB (e.g. could not be a person who works for a TCB or a company that owns or is owned by the TCB)  cannot be a [FCC recognised] Lab or affiliated with a test lab (e.g. could not be a person who works for a Lab or a company that owns or is owned by the Lab)  Agent can be Individual Entity or a Company Entity  Agent Entity must be located in US, US address/phone  Entity acting as Agent must have FRN (best practice, put FRN on Agent Letter)  Agent letter does not have to be FCC ID specific, can be general Agent for Grantee For devices being marketed or for which marketing has ceased for less than 1 year, if the Agent for Process of Service changes, then for every TC Number the TCB must request the FCC to put application into Audit Mode and Agent Letter needs to be updated (superseded). NOTE: The U.S. Agent for Service of Process should not be confused with the authorized agent used for signing the 731 form, other cover letters within the application, and/or the agent who may interface with the TCB. AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 U.S. Agent Designation for Service of Process ATTENTION: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA REGARDING: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Approve-IT, Inc. Contact Name: Nathan Grinager Street Address: 8011 34 th Ave South, Suite 342 City/Province/Zip: Bloomington, MN 55425 Telephone No: 651-247-1678 Email: [email protected] FRN #: 0027533835 This letter is to confirm that we (“the Designated U.S. Agent ) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by secti on 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: February 17, 2025 Signed by (Printed Name/Title): Nathan Grinager / Co-President The Applicant confirms its explicit consent and acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: AzureWave Technologies, Inc. Service Type: original application, class 2 permissive change Grantee Code: TLZ Grantee FRN: 0013946611 Module type: (single-modular transmitter) Contact Name: Patrick Lin Street Address: 8F., No.94, Baozhong Rd. , Xindian Dist. City/Province/Zip: New Taipei City , Taiwan 231 Telephone No: 02-55995599 *5580 Email: [email protected] Applicant Signature: Date: February 13, 2025 Signed by (Printed Name/Title): Patrick Lin/ Director *By signing this letter, the client declares and agrees that the service provided by Approve-IT, Inc. will only be applicable for the module models described above. The client also declares and accepts that the service won’t be applicable in any way to any host devices that could contain the modules for which the service has been contracted.

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: July 30, 2025 FCC ID: TLZ-CU640 RE: Covered listed Attestation Part 2.911(d)(5)(i) Filing AzureWave Technologies, Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. AzureWave Technologies, Inc. (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. Or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. RE: Attestation Statements Part 2.911(d)(5)(ii) Filing AzureWave Technologies, Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Applicant : AzureWave Technologies, Inc. Address : 8F., No. 94, Baozhong Rd., Xindian Dist., New Taipei City 23144, Taiwan Signature : _________________________________ Name and Job Title : Patrick Lin, Director E-mail : [email protected] Tel. : 02-55995599

Request for Confidentiality Date: July 30, 2025 Federal Communications Commission Authorization and Evaluation Division Subject: Request for confidentiality FCC ID: TLZ-CU640 To whom it may concern: Short-term Confidentiality pursuant to Public Notice DA 04-1705, and in order to comply with the marketing regulations in 47 C.F.R. §2.803 and the importation rules in 47 C.F.R. §2.1204 while ensuring that business-sensitive information remains confidential until the actual marketing of newly authorized devices, we are request the Commission grant temporary confidential treatment and not release the following attachments for routine public disclosure until 90 days after the grant date. 1. Internal Photographs 2. External Photographs 3. User’s manual 4. Test Set up photos Permanent Confidentiality Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. 1. Block Diagram 2. Schematics Diagram 3. Operational Description / Software Security For U-NII Devices It is our understanding that test measurement reports and correspondence during the certification review process cannot be granted confidential treatment, and such information will be available for public review once the grant of equipment authorization is issued. Sincerely, Applicant : AzureWave Technologies, Inc. Address : 8F., No. 94, Baozhong Rd., Xindian Dist., New Taipei City 23144, Taiwan Signature : _________________________________ Name and Job Title : Patrick Lin, Director E-mail : [email protected] Tel. : 02-55995599

February 19, 2024 To Whom It May Concern, The following is to document the similarities between CYW5551/2/3 and CYW55911/2/3 Wi-Fi + Bluetooth combo ICs, for the purpose of regulatory consideration. CYW55513 and CYW55913 is a superset device that encompasses all the circuitry and electrical, mechanical, and physical construction of the CYW55512/ CYW55912 and CYW55511/ CYW55911 devices. CYW55512/CYW55912 and CYW55511/CYW55911 devices are electrically, mechanically, and physically identical to the circuitry and construction of the CYW55513/CYW55913 superset devices, with the following differences only: 1. CYW55511/CYW55911 is single band operating in 2.4GHz 2. CYW55512/CYW55912 is dual band operating in 2.4G and 5GHz 3. CYW55513/CYW55913 is tri-band operating in 2.4G, 5G, and 6GHz For identical board designs using CYW55511/2/3 and CYW55911/2/3 separate certification IDs should not be needed. Sincerely, Juan Martinez Compliance Engineer Infineon Technologies

Agent Authorization Letter Date: July 30, 2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: TLZ-CU640 Product Name: IEEE802.11 a/b/g/n/ac/ax and Bluetooth LE 5.4 LGA Module To whom it may concern: We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization to the FCC Rules and Regulations. Sporton International Inc. Address : No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Name : Leo Huang Job Title : VP e-mail : [email protected] We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant : AzureWave Technologies, Inc. Address : 8F., No. 94, Baozhong Rd., Xindian Dist., New Taipei City 23144, Taiwan Signature : _________________________________ Name and Job Title : Patrick Lin, Director E-mail : [email protected] Tel. : 02-55995599

Date: December 3, 2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Model Deviation FCC ID: TLZ-CU640 To whom it may concern: We, AzureWave Technologies, Inc. hereby declares that the product versions described below are electronically identical. Product Marketing Model Number: AW-CU640-P , AW-CU642-P , AW-CU699-P , AW-CU640-E , AW-CU642-E , AW-CU699-E The differences listed as below Model Antenna Type Chipset WLAN 2.4G WLAN 5G WLAN 6G Bluetooth AW-CU640-P PCB CYW55913 with with with with AW-CU642-P CYW55912 with with without with AW-CU699-P CYW55911 with without without with AW-CU640-E PIFA CYW55913 with with with with AW-CU642-E CYW55912 with with without with AW-CU699-E CYW55911 with without without with The EUT has six model names that are identical in all aspects except for the supported wireless functionalities and antenna type. The wireless differences are implemented solely through software configuration, with the firmware being the same and requiring no hardware changes. Sincerely, Applicant : AzureWave Technologies, Inc. Address : 8F., No. 94, Baozhong Rd., Xindian Dist., New Taipei City 23144, Taiwan Signature : _________________________________ Name and Job Title. : Patrick Lin, Director E-mail : [email protected] Tel. : 02-55995599

Modular Approval Request Letter Date: July 30, 2025 Subject: Modular Approval Attestation FCC ID: TLZ-CU640 Dear Reviewer, We, AzureWave Technologies, Inc., would request IEEE802.11 a/b/g/n/ac/ax and Bluetooth LE 5.4 LGA Module approved under module approval authorization. The requirements regulated in 47 CFR 15.212 have been fulfilled and clearly explained below. Items to be covered by Single modular transmitters. Answer from applicant 1. The modular transmitter must have its own RF shielding. Yes, The EUT module contained its own RF shield. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Yes. Buffer chipset model CYW55913, CYW55912, CYW55911 3. The modular transmitter must have its own power supply regulation. Yes. Regulator chipset model CYW55913, CYW55912, CYW55911 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). Yes 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Yes 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). Yes 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. Yes 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Yes Please do not hesitate to contact me for any questions of this request letter. Thank you. Applicant : AzureWave Technologies, Inc. Address : 8F., No. 94, Baozhong Rd., Xindian Dist., New Taipei City 23144, Taiwan Signature : _________________________________ Name and Job Title : Patrick Lin, Director E-mail : [email protected] Tel. : 02-55995599

Radio Exposure Evaluation Report Report No. : FA570905 TEL : 886-3-327-3456 Page Number : 1 of 13 FAX : 886-3-327-0973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-A1 Ver5.0 Report Version : 01 FCC ID: TLZ-CU640 Radio Exposure Evaluation Report FCC ID : TLZ-CU640 Equipment : IEEE802.11 a/b/g/n/ac/ax and Bluetooth LE 5.4 LGA Module Brand Name : AzureWave Model Name : AW-CU640-P , AW-CU642-P , AW-CU699-P , AW-CU640-E , AW-CU642-E , AW-CU699-E Applicant : AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Manufacturer : AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Standard : 47 CFR FCC Part 2 Subpart J, section 2.1091 The product was received on Jul. 14, 2025, and testing was started from Jul. 18, 2025 and completed on Dec. 03, 2025. We, SPORTON INTERNATIONAL INC. Hsinhua Laboratory, would like to declare that the tested sample has been evaluated in accordance with the procedures given in 47 CFR FCC Part 2 Subpart J, section 2.1091 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Hsinhua Laboratory, the test report shall not be reproduced except in full. ___________________________________________ Approved by: Jackson Tsai __________________________________________ SDoC by: XXXXX SPORTON INTERNATIONAL INC. Hsinhua Laboratory No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411, Taiwan (R.O.C.) Radio Exposure Evaluation Report Report No. : FA570905 TEL : 886-3-327-3456 Page Number : 2 of 13 FAX : 886-3-327-0973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-A1 Ver5.0 Report Version : 01 FCC ID: TLZ-CU640 Table of Contents HISTORY OF THIS TEST REPORT .................................................................................................................. 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 Applicable Standards ............................................................................................................................. 8 1.3 Testing Location ..................................................................................................................................... 8 2 MAXIMUM PERMISSIBLE EXPOSURE ............................................................................................... 9 2.1 Limit of Maximum Permissible Exposure ............................................................................................... 9 2.2 RF Exposure Exempt Measurement .................................................................................................... 10 2.3 Multiple RF Sources Exposure ............................................................................................................. 11 2.4 MPE Calculation Method ...................................................................................................................... 12 2.5 Calculated Result and Limit .................................................................................................................. 13 Photographs of EUT V01 Radio Exposure Evaluation Report Report No. : FA570905 TEL : 886-3-327-3456 Page Number : 3 of 13 FAX : 886-3-327-0973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-A1 Ver5.0 Report Version : 01 FCC ID: TLZ-CU640 History of this test report Report No. Version Description Issued Date FA570905 01 Initial issue of report Dec. 10, 2025 Radio Exposure Evaluation Report Report No. : FA570905 TEL : 886-3-327-3456 Page Number : 4 of 13 FAX : 886-3-327-0973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-A1 Ver5.0 Report Version : 01 FCC ID: TLZ-CU640 Summary of Test Result Report Clause Ref Std. Clause Test Items Result (PASS/FAIL) Remark 2 - Exposure evaluation PASS - Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: None Reviewed by: Ben Tseng Report Producer: Debby Hung Radio Exposure Evaluation Report Report No. : FA570905 TEL : 886-3-327-3456 Page Number : 5 of 13 FAX : 886-3-327-0973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-A1 Ver5.0 Report Version : 01 FCC ID: TLZ-CU640 1 General Description 1.1 Information 1.1.1 EUT General Information RF General Information Evaluation Mode Frequency Range (MHz) Operating Frequency (MHz) Modulation Type 2.4GHz WLAN 2400-2483.5 2412-2462 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11g/n: OFDM (BPSK, QPSK, 16QAM, 64QAM) VHT: OFDM (BPSK, QPSK, 16QAM, 64QAM, 256QAM) 802.11ax: OFDMA (BPSK, QPSK, 16QAM, 64QAM, 256QAM, 1024QAM) 5GHz WLAN 5150-5250 5250-5350 5470-5725 5725-5850 5180-5240 5260-5320 5500-5720 5745-5825 802.11a/n: OFDM (BPSK, QPSK, 16QAM, 64QAM) 802.11ac: OFDM (BPSK, QPSK, 16QAM, 64QAM, 256QAM) 802.11ax: OFDMA (BPSK, QPSK, 16QAM, 64QAM, 256QAM, 1024QAM) 6GHz WLAN 5925-7125 5955-7115 802.11ax: OFDMA (BPSK, QPSK, 16QAM, 64QAM, 256QAM, 1024QAM) Bluetooth 2400-2483.5 2402-2480 LE: DSSS (GFSK) Radio Exposure Evaluation Report Report No. : FA570905 TEL : 886-3-327-3456 Page Number : 6 of 13 FAX : 886-3-327-0973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-A1 Ver5.0 Report Version : 01 FCC ID: TLZ-CU640 1.1.2 Antenna Information Ant. Brand Model Name Antenna Type Connector 1 ARISTOTLE RFA‐27‐JP326MHF4C198 PIFA I-Pex 2 ARISTOTLE RFA‐27‐JP326-C198 PIFA I-Pex 3 AzureWave AW-CU640 PCB N/A Ant. Port Gain (dBi) 2.4G 5G 6G BT UNII-1 UNII-2A UNII-2C UNII-3…

Text truncated - open the document above for the full version.

FCC Radio Test Report Report No. : FR570905AN TEL : 886-3-3273456 Page Number : 1 of 29 FAX : 886-3-3270973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-D1 Ver4.6 Report Version : 01 FCC ID: TLZ-CU640 FCC Radio Test Report FCC ID : TLZ-CU640 Equipment : IEEE802.11 a/b/g/n/ac/ax and Bluetooth LE 5.4 LGA Module Brand Name : AzureWave Model Name : AW-CU640-P , AW-CU642-P , AW-CU699-P , AW-CU640-E , AW-CU642-E , AW-CU699-E Applicant : AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Manufacturer : AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Standard : 47 CFR FCC Part 15.407 The product was received on Jul. 14, 2025, and testing was started from Jul. 18, 2025 and completed on Aug. 01, 2025. We, SPORTON INTERNATIONAL INC. Hsinhua Laboratory, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.10-2020 + Cor.1-2023 + C63.10a-2024 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Hsinhua Laboratory, the test report shall not be reproduced except in full. ___________________________________________ Approved by: Jackson Tsai __________________________________________ SDoC by: XXXXX SPORTON INTERNATIONAL INC. Hsinhua Laboratory No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411, Taiwan (R.O.C.) FCC Radio Test Report Report No. : FR570905AN TEL : 886-3-3273456 Page Number : 2 of 29 FAX : 886-3-3270973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-D1 Ver4.6 Report Version : 01 FCC ID: TLZ-CU640 Table of Contents HISTORY OF THIS TEST REPORT .................................................................................................................. 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 Testing Applied Standards ..................................................................................................................... 9 1.3 Testing Location Information .................................................................................................................. 9 1.4 Measurement Uncertainty ...................................................................................................................... 9 2 TEST CONFIGURATION OF EUT....................................................................................................... 10 2.1 Test Channel Mode .............................................................................................................................. 10 2.2 The Worst Case Measurement Configuration ...................................................................................... 11 2.3 Support Equipment ............................................................................................................................... 12 2.4 Test Setup Diagram ............................................................................................................................. 13 3 TRANSMITTER TEST RESULT .......................................................................................................... 17 3.1 AC Power-line Conducted Emissions .................................................................................................. 17 3.2 Emission Bandwidth ............................................................................................................................. 19 3.3 Maximum Conducted Output Power .................................................................................................... 20 3.4 Peak Power Spectral Density ............................................................................................................... 22 3.5 Unwanted Emissions ............................................................................................................................ 24 4 TEST EQUIPMENT AND CALIBRATION DATA ................................................................................ 28 APPENDIX A. TEST RESULTS OF AC POWER-LINE CONDUCTED EMISSIONS APPENDIX B. TEST RESULTS OF EMISSION BANDWIDTH APPENDIX C. TEST RESULTS OF MAXIMUM CONDUCTED OUTPUT POWER APPENDIX D. TEST RESULTS OF PEAK POWER SPECTRAL DENSITY APPENDIX E. TEST RESULTS OF UNWANTED EMISSIONS APPENDIX F. TEST PHOTOS PHOTOGRAPHS OF EUT V01 FCC Radio Test Report Report No. : FR570905AN TEL : 886-3-3273456 Page Number : 3 of 29 FAX : 886-3-3270973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-D1 Ver4.6 Report Version : 01 FCC ID: TLZ-CU640 History of this test report Report No. Version Description Issued Date FR570905AN 01 Initial issue of report Dec. 10, 2025 FCC Radio Test Report Report No. : FR570905AN TEL : 886-3-3273456 Page Number : 4 of 29 FAX : 886-3-3270973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-D1 Ver4.6 Report Version : 01 FCC ID: TLZ-CU640 Summary of Test Result Report Clause Ref. Std. Clause Test Items Result (PASS/FAIL) Remark 1.1.2 15.203 Antenna Requirement PASS - 3.1 15.207 AC Power-line Conducted Emissions PASS - 3.2 15.407(a) Emission Bandwidth PASS - 3.3 15.407(a) Maximum Conducted Output Power PASS - 3.4 15.407(a) Peak Power Spectral Density PASS - 3.5 15.407(b) Unwanted Emissions PASS - Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and explanations: None Reviewed by: Ben Tseng Report Producer: Debb…

Text truncated - open the document above for the full version.

FCC DFS Test Report Report No. : FZ570905 TEL : 886-3-327-3456 Page Number : 1 of 26 FAX : 886-3-327-0973 Issued Date : Dec. 10, 2025 Report Template No.: HE1-D2 Ver3.2 Report Version : 01 FCC ID : TLZ-CU640 FCC DFS Test Report FCC ID : TLZ-CU640 Equipment : IEEE802.11 a/b/g/n/ac/ax and Bluetooth LE 5.4 LGA Module Brand Name : AzureWave Model Name : AW-CU640-P , AW-CU642-P , AW-CU699-P , AW-CU640-E , AW-CU642-E , AW-CU699-E Applicant : AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Manufacturer : AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Standard : 47 CFR FCC Part 15.407 The product was received on Jul. 14, 2025, and testing was started from Aug. 05, 2025 and completed on Aug. 05, 2025. We, SPORTON INTERNATIONAL INC. Hsinhua Laboratory, would like to declare that the tested sample has been evaluated in accordance with the procedures given in KDB 905462 D02 UNII DFS Compliance Procedures New Rules v02 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNA…

Text truncated - open the document above for the full version.