TS5-6050M-PT200Wireless Tracking Device

SENDUM WIRELESS, CORP. Table of Contents 1 Purpose.....................................................................................................3 2 Introduction..............................................................................................3 2.1 What is a PT200..................................................................................................3 2.2 How does a PT200 work.....................................................................................3 3 Getting Started.........................................................................................3 3.1 Battery Tips.........................................................................................................3 3.2 Installing the Battery...........................................................................................4 3.3 Removing the Battery..........................................................................................4 3.4 Charging the Battery...........................................................................................4 3.4.1 Charging using the PT200 Device..............................................................4 3.4.2 Charging using Gang Charger....................................................................4 4 Provisioning Your Device........................................................................4 5 PT200 Command Set...............................................................................5 6 Locating Your PT200...............................................................................6 6.1 Frequent Tracking..............................................................................................6 6.2 Periodic Tracking...............................................................................................7 6.3 Fast Tracking......................................................................................................7 7 Using the Diagnostic Tool.......................................................................7 8 Troubleshooting.......................................................................................8 9 HUMAN EXPOSURE COMPLIANCE STATEMENT.........................9 10 Important Safety and Legal Information..............................................9 10.1 RF Energy Interference/Compatibility.............................................................10 SENDUM WIRELESS, CORP. 1 Purpose The purpose of this guide is to describe the basic features of the PT200. 2 Introduction 2.1 What is a PT200 ÿ The PT200 is a wireless tracking device which operates on the CDMA network using assisted GPS for location. ÿ It is used for tracking valuable packages or assets. 2.2 How does a PT200 work ÿ It establishes a data connection through either the cellular or the PCS band similar to a mobile phone. ÿ A user can send a SMS message through an internet connection or a mobile phone to the device by calling its phone number. The device gets its location and send it back to the user via the CDMA network. 3 Getting Started 3.1 Battery Tips Battery life depends on the network, signal strength, temperature, features, and accessories you use. ÿ Always use Sendum Original batteries and battery chargers. The warranty does not cover damage caused by non-Sendum batteries and/or chargers. ÿ New batteries or batteries stored for a long time may take more time to charge. ÿ When charging your battery, keep it near room temperature. ÿ When storing your battery, keep it uncharged in a cool, dark, dry place, such as a refrigerator. ÿ Never expose batteries to temperatures below -10°C (14°F) or above 45°C (113°F). Always take your device with you when you leave your vehicle. ÿ It is normal for batteries to gradually wear down and require longer charging times. If you notice a change in your battery life, it is probably time to purchase a new battery. Contact your local recycling center for proper battery disposal. Warning: Never dispose of batteries in a fire because they may explode. Before using your device, please read the battery safety information in the Safety and General Information section included in this guide. SENDUM WIRELESS, CORP. 3.2 Installing the Battery Slide the battery pack into the PT200 battery slot using the guiding tabs until the latch clicks into place. 3.3 Removing the Battery Pull the latch and slide the battery pack away from the PT200 housing at the same time. 3.4 Charging the Battery New batteries are shipped partially charged. Before you can use your device, install and charge the battery as described below. Some batteries perform best after several full charge/discharge cycles. 3.4.1 Charging using the PT200 Device Simply attached the Sendum charger into the device and plug the AC adapter to the AC outlet. 3.4.2 Charging using Gang Charger Attached the battery pack to the Sendum external charger slot. 4 Provisioning Your Device ÿ Connect your device using the sendum USB cable. If problem communicating with the device. Use the following documents for troubleshooting: DEX00003 (DOC QUALCOMM USB DRIVER INSTALLATION).doc ÿ Open the Sendum Provisioning Tool. Should look like: SENDUM WIRELESS, CORP. ÿ Select the com port that the device is communicating, then press “Connect”. The ESN will be shown. ÿ If the device is already provisioned, the “Read” button is used to check. ÿ Now all provisioning parameters can be entered into the appropriate boxes. ÿ Press “Write” to load into the device. 5 PT200 Command Set The PT200 supports the following commands. There are sent to the device using SMS messages: //BREW:0x12345678:PSW2,PROVISION,PDE,<ip_address>:<port> Sets the PDE address used by the device. In control plane architectures, this is the address of the Control Plane Server. In user plane architectures, this is the address of the actual PDE. //BREW:0x12345678:PSW2,PROVISION,APP,<ip_address>:<port> Sets the APP address of used by the device. All messages from the device are sent to this IP addr…

Text truncated - open the document above for the full version.

4500 Beedie Street, Burnaby BC, Canada, V5J 5L2 www.sendum.com Main: 604.438.9741 Fax: 604.437.5726 This document contains information which is proprietary and confidential to Sendum Wireless, Corp. Disclosure to persons other than the officers, employees, agents, or subcontractors of the Company or licensee of this document without the prior written permission of Sendum Wireless, Corp. is strictly prohibited. Date: Nov. 18/05 Sendum Wireless Corp. 4500 Beedie Street Burnaby, BC, V5J 5L2 Canada Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA, 92121, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko USA, Inc, still resides with Sendum Wireless Corp. 4500 Beedie Street, Burnaby, BC, V5J 5L2, Canada. Dated this 16 Day of Nov. 20 05 Agency agreement expiration date: Nov. 20, 2006 By: Kerry Zoehner Signature Printed Title: VP of Engineering On behalf of : Sendum Wireless Corp Telephone: (604) 438-6451 Sendum

4500 Beedie Street, Burnaby BC, Canada, V5J 5L2 www.sendum.com Main: 604.438.9741 Fax: 604.437.5726 This document contains information which is proprietary and confidential to Sendum Wireless, Corp. Disclosure to persons other than the officers, employees, agents, or subcontractors of the Company or licensee of this document without the prior written permission of Sendum Wireless, Corp. is strictly prohibited. Date: Nov. 18/05 Sendum Wireless Corp. 4500 Beedie Street Burnaby, BC, V5J 5L2 Canada Re: Request of Confidentiality (FCC ID: TS5-6050M-PT200) Pursuant to Sections 0.457(d)(I)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying as outlined below: Schematics, Parts List, Operating Description, Block Diagrams The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(I)(ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. Sincerely, Kerry Zoehner VP of Engineering Sendum Wireless Corp. . Sendum

Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 where:S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna 23.9dBmFrom test report's measured radiated power. Maximum peak output power at antenna input terminal:23.9(dBm) Maximum peak output power at antenna input terminal:0.245(W) Antenna gain(typical):-0.50(dBi) Maximum antenna gain:0.89(numeric) Prediction distance:20.00(cm) Prediction frequency:1908.75(MHz) MPE limit for uncontrolled exposure at prediction frequency:1.00(mW/cm^2) Power density at prediction frequency:0.044(mW/cm^2) Maximum allowable antenna gain:43.11(dBi) Margin of Compliance:13.61dB 2 4R PG S π = Therefore the power density at 20 cm is 490/4/PI/20^2 = 0.044 mW/cm2

Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 where:S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna 22.8dBmFrom test report's measured radiated power. +2.1 24.9dBmEIRP Maximum peak output power at antenna input terminal:24.9(dBm) Maximum peak output power at antenna input terminal:0.309(W) Antenna gain(typical):-1.00(dBi) Maximum antenna gain:0.79(numeric) Prediction distance:20.00(cm) Prediction frequency:824.70(MHz) MPE limit for uncontrolled exposure at prediction frequency:1.00(mW/cm^2) Power density at prediction frequency:0.049(mW/cm^2) Maximum allowable antenna gain:42.11(dBi) Margin of Compliance:13.1dB 2 4R PG S π = Therefore the power density at 20 cm is 490/4/PI/20^2 = 0.049 mW/cm2

Nemko USA, Inc. Phone (858) 755-5525 Fax (858) 452-1810 11696 Sorrento Valley Rd., Suite F San Diego, CA 92121-1024 Test Report: 2005 110898-FCC1 Applicant: Sendum Wireless Corporation 4500 Beedie Street Burnaby, BC Canada V5J 5L2 Phone: 604 438 6451 Fax: 604 437 5726 Apparatus: PT200 FCC ID: TS5-6050M-PT200 In Accordance With: FCC Part 22, Subpart H Public Mobile Services RSS-129, Issue 2 800MHz Dual-Mode CDMA Cellular Telephones FCC Part 24, Subpart E RSS-133, Issue 2, Rev.1 2GHz Personal Communications Services Tested By: Nemko USA Project Number: 25-898-SEN Date: Nov. 17, 2005 Total Number of Pages: 50 Nemko USA REPORT SUMMARY Report Number: 2005 110898-FCC1 FCC ID # TS5-6050M-PT200 Specification: FCC Part 22 & 24 Page 2 of 50 Report Summary These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 22. Conducted measurements were performed in accordance with ANSI TIA-603-B-2002. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. The assessment summary is as follows: Apparatus Assessed: PT200 Specification: FCC Part 22 Public Mobile Services FCC Part 24, Subpart E RSS-129, Issue 2 RSS-133, Issue 2 Compliance Status: Complies Exclusions: None Non-compliances: None Report Release History: REVISION DATE COMMENTS - 11-10-05 Prepared By: A. Laudani - Initial Release: Chip Fleury Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko USA. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. Nemko USA REPORT SUMMARY Report Number: 2005 110898-FCC1 FCC ID # TS5-6050M-PT200 Specification: FCC Part 22 & 24 Page 3 of 50 TABLE OF CONTENTS Report Summary........................................................................................................................................2 Section 1: Equipment Under Test.............................................................................................................4 1.1 Product Identification................................................................................................................................4 1.2 Samples Submitted for Assessment...........................................................................................................5 1.3 Theory of Operation..................................................................................................................................5 1.4 Technical Specifications of the EUT.........................................................................................................6 1.5 Block Diagram of the EUT........................................................................................................................6 Section 2: Test Conditions.........................................................................................................................7 2.1 Specifications.............................................................................................................................................7 2.2 Deviations From Laboratory Test Procedures...........................................................................................7 2.3 Test Environment.......................................................................................................................................7 2.4 Test Equipment..........................................................................................................................................7 Section 3: Observations..............................................................................................................................8 3.1 Modifications Performed During Assessment...........................................................................................8 3.2 Record Of Technical Judgements..............................................................................................................8 3.3 EUT Parameters Affecting Compliance....................................................................................................8 3.4 Test Deleted...............................................................................................................................................8 3.5 Additional Observations............................................................................................................................8 Section 4: Results Summary......................................................................................................................9 Appendix A: Test Results........................................................................................................................10 Frequency Stability...............................................................................................................................................10 Output Power........................................................................................................................................................12 Part 22 Low Frequency Output Power..........................................................................................................17 Mid Frequency Output Power.........................................................................................................................18 High Frequency Output P…

Text truncated - open the document above for the full version.

Para. No 2.1046 Conducted Output Power Para. No 2.1049 Bandwidth Para. No. 2.1051 Spurious Emissions at Antenna Terminals Para. No. 2.1053 - Field Strength of Spurious Radiation EUTAttenuator Radio Communication Monitor Spectrum Analyzer 3 METERS EUT NON-CONDUCTING TURN-TABLE 0.8 METER VARIABLE SEARCH HEIGHT (1 TO 4 m) TO TEST RECEIVER/SPECTRUM ANALYZER SEARCH ANTENNA Para. No. 2.1055 - Frequency Stability Climate Chamber EUT Variable Power Supply Attenuator Frequency Counter Spectrum Analyzer Multimeter Substitution Conducted Emissions Test Configuration