TTC-BT-100Bluetooth EarPhone

BT-100 Instructions guide Keys and parts The headset contains several technological features to improve the experience of the user. The following section is an overview of the parts: Before using the headset, you must fully charge the battery and connect the headset to your respective Bluetooth device. HOW TO CHARGE THE BATTERY The headset contains a battery capable of up to 4 hours of usage. To charge the battery, remove the charging cover on the right earbud to expose the micro-USB port. Plug the USB cable into the headset and the charging source to begin charging. The LED indicator will show a constant red light when charging. Once the battery is fully charged, the LED light will be turned off. When the battery is low, the LED indication will change from blue to red, there will also be a voice prompt “Battery low”. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine; fire or the like. TO TURN ON/OFF HEADSET Press and hold 1 seconds of the Multi-function button until the LED light comes on. The LED light will show a constant red light for 1 second, there will also be a voice prompt “Power on”, the headset now is turned on (not paired). If you wish to turn off the headset, press the Multi-function button and hold for 3 seconds until the indicator will show a constant red light (for 2s), there will also be a voice prompt “Power off”. Let go of the button and the device is now turned off. CONNECT WITH BLUETOOTH DEVICE To pair the headset with a Bluetooth device, ensure that the respective device is turned on and the Bluetooth function is active. When setting the headset for pairing mode, make sure the headset is off, then press the Multi- function button and hold for 5 seconds, until the LED flashes alternatively with red and blue lights, there will also be a voice prompt “Pairing”. On your respective device you should search for the signal and use the device's functions to connect. On the list of found devices you select "BT-100" to establish the connection. Some devices require a passcode to connect with a newly established Bluetooth apparatus. Enter passcode: 0000 if necessary. When the connection is established, the headset's light indicator will flash a blue light two times every 5 seconds to verify the connection, there will also be a voice prompt “Connected”. NFC PAIRING The headset has the NFC (Near Field Communication) Bluetooth technology incorporated and can be used if your respective Bluetooth device is compatible. To pair with NFC, first enable the NFC function on the Bluetooth device. Place the left earbud near the device; the device should recognize the signal from the headset. If the music device and the headset are pairing for the first time, you will need to accept the pairing on the music device. Once accepted, the headset is paired (a blue light will flash two times every 5 seconds) and ready to use. CONTROL FUNCTIONS Function Action Turn on Press and hold (1 sec) Multi-function button until LED shows a constant light for 1 second Turn off Press and hold (3 sec) Multi-function button until LED shows a constant light for 2 second Play/Pause music Press the Multi-function button once Answer/End call Press the Multi-function button once Reject call Press the Multi-function button twice Adjust volume Press the Volume up or Volume down button once Skip track forward Press and hold (1 sec) Volume up button Skip track back Press and hold (1 sec) Volume down button (Remark: this action may restart track on some devices instead) DISCONNECT THE HEADSET If you wish to disconnect the established connection between the headset and your respective device, simply enter the Bluetooth function on your music player and shut down the connection or switch off the headset. CLEAR PAIR SETTING To clear the pairing settings from the headset, you should first turn off the headset. Press and hold the Multi-function button simultaneously with the Volume down button. The two buttons has to be pressed and hold for 5 seconds. The indicating light will switch between a red and blue flash 3 times and the headset has now been clear the pairing settings. RESET HEADSET To hardware reset the headset, connect to the USB cable to a charging source. The following section contains information regarding safety warnings, requirements and statements. Please read and understand thoroughly before using the headset. Safety requirements  Heed all warnings  Keep and follow all instructions.  The operating temperature range in user manual: from 0 degree Celsius to 45 degree Celsius.  DO NOT use this apparatus near water  Clean only with dry cloth  DO NOT disassemble or replace the battery. If you suspect there is something wrong with the battery, please carry the unit to the service center for help.  CAUTION: RISK OF EXPLOSION IF BATTRY IS REPLACED BY AN UNCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS  The battery should not be disposed together with other waste. The battery has to be disposed at an authorized place for recycling of electrical and electronic appliances. By collecting and recycling waste, you help save natural resources, and make sure the product is disposed in an environmental friendly and healthy way.  Unplug this apparatus during lightning storms or when unused for long periods of time  DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat  Only use accessories specified by the manufacturer  Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.  If at any time in the …

Text truncated - open the document above for the full version.

Date (10/February/2015) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: TTC-BT-100 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, we Fujikon Industrial Co., Ltd. hereby requests permanent confidential treatment of information accompanying this application as outlined below: Schematics Block Diagrams Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Company Officer: Dennis Chan Telephone Number: +852 9067 5029 Email: [email protected] Fax: +852 2694 1338 Company name: Fujikon Industrial Co., Ltd. /Electronic Engineering Manager

Title: Electronic Engineering Manager Date (10/February/2015) Dear Sir or Madam, We, Fujikon Industrial Co. Ltd. 16/F Grand Central Plaza, 138 Shatin Rural Committee Rd. Shatin NT HONG KONG hereby authorize Bureau Veritas Shenzhen Co. Ltd. Dongguan Branch to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that neither we nor any party to this application are subject to denial of U.S Federal benefits, which include FCC benefits, pursuant to section 5301 of Anti-Drug Abuse Act of 1988, U.S.C 862 because of conviction for possession or distribution of controlled substance. This authorization is application to product: Type of equipment: Bluetooth Earphone Model name: BT-100 FCC ID: TTC-BT-100 This authorization expires one year from the current date. Sincerely, Company Officer: Dennis Chan Telephone Number: +852 9067 5029 Email: [email protected] Fax: +852 2694 1338 Company name: Fujikon Industrial Co., Ltd.

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 2 Report Version 1 Reference No.: 141231N010 PHOTOGRAPHS OF THE EUT Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 2 Report Version 1 Reference No.: 141231N010

Model n o: B T-100Model n o: BT-100 100 100 Model n o: B T-100 100 45mm 5mm 15mm

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 6 Report Version 1 Reference No.: 141231N010 PHOTOGRAPHS OF THE EUT Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 6 Report Version 1 Reference No.: 141231N010 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 3 of 6 Report Version 1 Reference No.: 141231N010 ANT Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 4 of 6 Report Version 1 Reference No.: 141231N010 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 5 of 6 Report Version 1 Reference No.: 141231N010 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 6 of 6 Report Version 1 Reference No.: 141231N010

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] No SAR justification for FCC ID : TTC-BT-100 Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where
 f(GHz) is the RF channel transmit frequency in GHz
 Power and distance are rounded to the nearest mW and mm before calculation
 The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Smallest distance from the antenna and radiating structures or outer surface of the device The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] The tuned conducted Average Power (declared by client) Mode Frequency (MHz) Target Power (dBm) Tolerance (dBm) Lower Tolerance (dBm) Upper Tolerance (dBm) BT2.1+EDR 2402-2480 0 +-2.0 -2.0 2.0 BT4.0 2402-2480 5.0 +-2.0 3.0 7.0 SAR Test Exclusion Thresholds Mode Frequency (MHz) Maximum source-based time averaged conducted output power (dBm) Minimum separation distance (mm) Result of Eq. 1 Limit for 1-g SAR Limit for 10-g extremit y SAR Verdict BT2.1+ EDR 2402 2.0 5 0.491 3.0 7.5 Exempt from SAR BT4.0 2480 7.0 5 1.579 3.0 7.5 Exempt from SAR Conclusion Therefore this device complies with FCC’s RF radiation exposure limits for general population without SAR evaluation.

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 36 Report Version 1 Test Report No.: RF141231N010-2 TEST REPORT Applicant Fujikon Industrial Co., Ltd. Address 16/F Tower 1, Grand Central Plaza, 138 Shatin Rural Committee Rd, Shatin N.T. Hong Kong Manufacturer or Supplier Fujikon Industrial Co., Ltd. Address 16/F Tower 1, Grand Central Plaza, 138 Shatin Rural Committee Road, Shatin, N.T. Hong Kong Product Bluetooth Earphone Brand Name Fujikon Model BT-100 Additional Model & Model Difference N/A Date of tests Dec. 31, 2014 ~ Feb. 02, 2015 the tests have been carried out according to the requirements of the following standard: FCC Part 15, Subpart C, Section 15.247 CONCLUSION: The submitted sample was found to COMPLY with the test requirement Tested by Yuqiang Yin Project Engineer / EMC Department Approved by Glyn He Supervisor / EMC Department Date: Feb. 03, 2015 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 36 Report Version 1 Test Report No.: RF141231N010-2 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 4 1 SUMMARY OF TEST RESULTS .................................................................................................... 5 2 MEASUREMENT UNCERTAINTY ................................................................................................. 5 3 GENERAL INFORMATION ............................................................................................................ 6 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................. 6 3.2 DESCRIPTION OF TEST MODES ............................................................................................... 7 3.2.1. CONFIGURATION OF SYSTEM UNDER TEST ............................................................... 7 3.2.2. TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................................... 7 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................ 10 3.4 DESCRIPTION OF SUPPORT UNITS ....................................................................................... 10 4 TEST TYPES AND RESULTS .......................................................................................................11 4.1 CONDUCTED EMISSION MEASUREMENT .............................................................................. 11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ................................................ 11 4.1.2 TEST INSTRUMENTS ...................................................................................................... 11 4.1.3 TEST PROCEDURES ..................................................................................................... 12 4.1.4 DEVIATION FROM TEST STANDARD ........................................................................... 12 4.1.5 TEST SETUP ................................................................................................................... 13 4.1.6 EUT OPERATING CONDITIONS .................................................................................... 13 4.1.7 TEST RESULTS .............................................................................................................. 14 4.2 RADIATED EMISSION MEASUREMENT .................................................................................. 16 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT .................................................... 16 4.2.2 TEST INSTRUMENTS ..................................................................................................... 17 4.2.3 TEST PROCEDURES ..................................................................................................... 18 4.2.4 DEVIATION FROM TEST STANDARD ........................................................................... 18 4.2.5 TEST SETUP ................................................................................................................... 19 4.2.6 EUT OPERATING CONDITIONS .................................................................................... 19 4.2.7 TEST RESULTS .............................................................................................................. 20 4.3 6dB BANDWIDTH MEASUREMENT ......................…

Text truncated - open the document above for the full version.

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 53 Report Version 1 Test Report No.: RF141231N010-1 TEST REPORT Applicant Fujikon Industrial Co., Ltd. Address 16/F Tower 1, Grand Central Plaza, 138 Shatin Rural Committee Rd, Shatin N.T. Hong Kong Manufacturer or Supplier Fujikon Industrial Co., Ltd. Address 16/F Tower 1, Grand Central Plaza, 138 Shatin Rural Committee Road, Shatin, N.T. Hong Kong Product Bluetooth Earphone Brand Name Fujikon Model BT-100 Additional Model & Model Difference N/A Date of tests Dec. 31, 2014 ~ Feb. 02, 2015 the tests have been carried out according to the requirements of the following standards: FCC Part 15, Subpart C, Section 15.247 CONCLUSION: The submitted sample was found to COMPLY with the test requirement Tested by Yuqiang Yin Project Engineer / EMC Department Approved by Glyn He Supervisor / EMC Department Date: Feb. 03, 2015 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 53 Report Version 1 Test Report No.: RF141231N010-1 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 5 1 SUMMARY OF TEST RESULTS...................................................................................................... 6 2 MEASUREMENT UNCERTAINTY .................................................................................................. 6 3 GENERAL INFORMATION.............................................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT........................................................................................... 7 3.2 DESCRIPTION OF TEST MODES............................................................................................. 7 3.2.1. CONFIGURATION OF SYSTEM UNDER TEST ............................................................... 9 3.2.2. TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL.................................... 9 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS...........................................................11 3.4 DESCRIPTION OF SUPPORT UNITS......................................................................................11 4 TEST TYPES AND RESULTS ....................................................................................................... 12 4.1. CONDUCTED EMISSION MEASUREMENT ........................................................................... 12 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................................... 12 4.1.2 TEST INSTRUMENTS..................................................................................................... 12 4.1.3 TEST PROCEDURES ..................................................................................................... 13 4.1.4 DEVIATION FROM TEST STANDARD ........................................................................... 13 4.1.5 TEST SETUP ................................................................................................................... 14 4.1.6 EUT OPERATING CONDITIONS .................................................................................... 14 4.1.7 TEST RESULTS............................................................................................................... 15 4.2. RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 17 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ...................... 17 4.2.2 TEST INSTRUMENTS .................................................................................................... 18 4.2.3 TEST PROCEDURES..................................................................................................... 19 4.2.4 DEVIATION FROM TEST STANDARD........................................................................... 20 4.2.5 TEST SETUP .................................................................................................................. 20 4.2.6 EUT OPERATING CONDITIONS ................................................................................... 20 4.2.7 TEST RESULTS.............................................................................................................. 21 4.3. NUMBER OF HOPPING FREQUENCY USED.....................................................................…

Text truncated - open the document above for the full version.