TWYIPJR640RFID Integrated Reader, IPJR640

UHF Gen 2 RFID Speedway ® Revolution Installation and Operations Guide Copyright © 2010, Impinj, Inc. i Products Covered by this Guide This guide pertains to readers with the following part numbers: Table i: Speedway Reader Part Numbers Reader Communication Code Part Number Speedway R220 FCC IPJ-REV-R220-USA1M1 Speedway R420 FCC IPJ-REV-R420-USA1M1 Speedway R220 ETSI IPJ-REV-R220-EU11M1 Speedway R420 ETSI IPJ-REV-R420-EU11M1 Speedway R220 Various IPJ-REV-R220-GX11M1 Speedway R420 Various IPJ-REV-R420-GX11M1 Speedway R640 FCC IPJR640 Speedway R640 ETSI IPJ-REV-R640-EU1M1 Speedway R640 Various IPJ-REV-R640-GX11M1 Federal Communications Commission (FCC) Compliance This equipment was tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation and cause harmful interference to radio or television reception. To determine if this equipment causes harmful interference to radio or television reception, turn the equipment off and on. You are encouraged to try to correct the interference by one or more of the following: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Consult the dealer or a qualified radio/TV technician for assistance. Caution: Changes to this product or modifications not expressly approved by the party responsible for compliance could void your authority to operate per FCC Part 15. Industry Canada (IC) Compliance Operation is subject to the following two conditions: (1) This device may not cause interference. Speedway Revolution Installation and Operations Guide Octane 4.4 ii Copyright © 2010, Impinj, Inc (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with the antenna(s) listed on page 32 that have a maximum gain of 6 dB. Antennas not included in this list or having a gain greater than 6 dB are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be chosen so that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication. The term “IC” before the radio certification number only signifies that Industry of Canada technical specifications were met. CE Marking and European Economic Area (EEA) RFID devices designed for use throughout the EEA must have a maximum radiated transmit power of 2W ERP in the frequency range of 865.6–867.6 MHz. For other EEA restrictions on RFID device use, please refer to the Impinj Declaration of Conformity (DoC) located at support.impinj.com. Before You Begin Warning: Please read this document in its entirety before operating the Speedway Revolution reader, as serious personal injury or equipment damage may result from improper use. Unauthorized opening of the Speedway Revolution reader enclosure voids the warranty. To safeguard personnel, be sure to position all antenna(s) according to the specified requirements for your regulatory region. For details, see “Appendix A: Information Specific to Regions of Operation” on page 33. Speedway Revolution Installation and Operations Guide Octane 4.4 Copyright © 2010, Impinj, Inc. iii Table of Contents Federal Communications Commission (FCC) Compliance........................................i Industry Canada (IC) Compliance..............................................................................i CE Marking and European Economic Area...............................................................ii Before You Begin......................................................................................................ii Chapter 1: Introduction..................................................................................................1 About this Guide.........................................................................................................1 Intended Audience....................................................................................................1 Other Documents of Interest.....................................................................................1 Impinj Support Information........................................................................................2 Introduction to Speedway ® Revolution.....................................................................3 Speedway xPortal – Integrated Portal Reader.........................................................4 Requirements for Using Speedway Revolution.......................................................4 Environmental Requirement......................................................................................4 Hardware Requirements...........................................................................................4 Power Requirements.................................................................................................5 Supported Operating Environments..........................................................................5 Supported Communication Protocol..........................................................................6 Antenna Requirements..............................................................................................6 Chapter 2: Installing and Connecting Speedway Revolution.....................................7 Speedway Revolution Ports and LEDs.....................................................................7 Installing and Connecting the Reader...............…

Text truncated - open the document above for the full version.

Impinj, Inc. 701 N. 34 th Street, Suite 300 Seattle, WA 98103 Tel (206) 517-5300 Fax (206) 517-5262 www.impinj.com 23 March 2009 To Whom It May Concern: This is your letter of authorization to accept our appointment of CKC Certification Services, LLC as Agent for Impinj, Inc., with principal offices at 701 N. 34 th Street, Suite 300, Seattle, WA 98103 to sign applications before the FCC or IC agencies on our behalf, and to receive and exchange data between our company and the agencies in connection with regulatory certifications. Sincerely, William Ashley VP Reader Engineering Impinj, Inc.

Impinj, Inc. 701 N. 34 th Street, Suite 300 Seattle, WA 98103 Tel (206) 517-5300 Fax (206) 517-5262 www.impinj.com 24 May 2010 To Whom It May Concern: With regard to the product identified herein, I hereby attest that the following modifications were made to the device RFID Reader, Model: IPJ-REV, FCC ID: TWYIPJREV. 1. The RFID reader is integrated in a radome housing with antenna element. 2. The RFID reader maximum transmit power is limited to 28.5dBm to insure compliance with 36 dBm EIRP limit (the antenna gain of the integrated antenna is 7.5dBi). After the modifications were made the device was tested for RF output and spurious emissions deviations. There were no deviations that exceeded the listed limits at the time of this new testing which shows that the test reports continue to demonstrate compliance. To further demonstrate compliance to the original testing of FCC ID: TWYIPJREV the following statements are also held to be true. 1. The radio-element (reader device) of the previously certified equipment is unchanged and operates in the same frequency range and with the same modulation types and protocol formats. 2. The device incorporates all the same functional characteristics and has the same intended end-use purpose as the FCC ID: TWYIPJREV. We are requesting certification as an Original/New Filing of the Model: IPJ-REV under a new Model and FCC ID. The New certification will reference the device as: RFID Integrated Reader, Model: IPJR640, FCC ID: TWYIPJR640. Sincerely, William Ashley VP Reader Engineering Impinj, Inc.

Impinj, Inc. 701 N. 34 th Street, Suite 300 Seattle, WA 98103 Tel (206) 517-5300 Fax (206) 517-5262 www.impinj.com 10 May 2010 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Section 0.457(d)(2)(i) and Section 0.459 pertaining to confidential material. Impinj, Inc. would like the following documents regarding this submission for FCC ID: TWYIPJR640 to be kept confidential. 1. ipjr640 Block Diagram and Description 2. ipjr640 Schematics The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, William Ashley VP Reader Engineering Impinj, Inc.

External Photographs – RFID Integrated Reader, IPJR640 Front view of device View of bottom View of top View of side View of back

RFID Integrated Reader, IPJR640 Label and Label Loca8on Rear view of Device Label a=ached to back Label size 2 ½” x 2” This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Assembled in USA xPortal RFID READER Impinj, Inc. FCC ID: TWYIPJR640 IC: 6324A-IPJREV

Internal Photographs – RFID Integrated Reader, IPJR640 Internal photograph – radome removed Close up of RFID reader (transmitter/receiver) Close up of label that indicates the transmitter can only be replaced with a specific SKU Side view of reader element Opposite Side view of reader element Close up of antenna module Close up of antenna module PCB. (Antenna module is unscrewed and flipped over for this photograph) Close up of antenna module PCB. (Antenna module is unscrewed and flipped over for this photograph) Isometric view of antenna module PCB. (Antenna module is unscrewed and flipped over for this photograph) Reader Element PCB - Top Reader Element PCB - Bottom

Page 1 of 5 Report No:90557-6 R MAXIMUM PERMISSIBLE EXPOSURE REPORT FOR THE RFID INTEGRATED READER MODEL NUMBER: IPJR640 DATE OF ISSUE: MAY 4, 2010 PREPARED FOR: Impinj, Inc. 701 N. 34th Street Seattle, WA 98103 PREPARED BY: Jeff Gilbert CKC Laboratories, Inc. 22116 23rd Drive SE, Suite A Bothell, WA 98021 W.O. No.: 90557 Date of test: April 21, 2010 Report No.:90557-6R Page 2 of 5 Report No:90557-6 R Purpose of Test: To demonstrate compliance with United States and Canada RF Exposure requirements for Mobile Equipment (devices used >20cm from the body), where Maximum Permissible Exposure (MPE) Calculations apply. United States MPE Limits in accordance with 1.1310: Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3-3.0 614 1.63 *(100) 6 3.0-30 1842/f 4.89/f *(900/f2) 6 30-300 61.4 0.163 1 6 300-1500 --- --- f/300 6 1500-100,000 --- --- 5 6 General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f2) 30 30-300 27.5 0.073 0.2 30 300-1500 --- --- f/1500 30 1500-100,000 --- --- 1 30 Note: Limit is calculated based on the mid-band frequency used in the operating frequency range. Page 3 of 5 Report No:90557-6 R Canadian MPE Limits in accordance with RSS-102: Occupational / Controlled Exposure: General Population / Uncontrolled Exposure Page 4 of 5 Report No:90557-6 R Equipment operational details: Operating Frequency (MHz) Measured Output Power (dBm) Maximum Mobile Antenna Gain (dBi) Maximum EIRP (dBm) 902-928 28.5 7.5 36 Measurements based from EMC Test Report: 90557-6 Device and Antenna Operating Configuration: Device operating at maximum output power with continuous transmission of modulated data. Test Procedure: This equipment is evaluated in accordance with the guidelines set forth in OET Guide 65 & ANSI C95.1 for the US and Health Canada Safety Code 6 & RSS 102 for Canada. Other Considerations: None MPE Calculations: Limit used: Occupational / Controlled Exposure X General Population / Uncontrolled Exposure MPE Limit = 1 (mW/cm 2 ) 2 2 4 )/( d EIRP cmmWDensityPower π = Given: EIRP in mW and d in cm EIRP (mW) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) Power Density (W/m 2 ) Limit (W/m 2 ) 3981.07 20 0.792009 1.0 0.079200905 10 Page 5 of 5 Report No:90557-6 R Statement of Compliance: This device demonstrates compliance under the operating conditions specified in this document. Under normal operating conditions, the antenna is designed to be installed in accordance with the manufacturer’s instructions in such a manor to maintain the minimum separation distance. The MPE calculations shown above demonstrate compliance to the provisions of US and Canadian requirements. As can be seen from the MPE results, this device passes the specified limits at a distance of 20 cm at the maximum output power under normal operating conditions.

Page 1 of 122 Report No: FC09-014 TESTING CERT #803.01, 803.02, 803.05, 803.06 IMPINJ INC TEST REPORT FOR THE RFID READER, IPJ-REV FCC PART 15 SUBPART C SECTIONS 15.207 & 15.247 AND RSS-210 ISSUE 7 TESTING DATE OF ISSUE: FEBRUARY 23, 2009 PREPARED FOR: Impinj, Inc. 701 N. 34th Street Seattle, WA 98103 PREPARED BY: Mary Ellen Clayton CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 P.O. No.: 100974 Date of test:February 9-12, 2009 W.O. No.: 89028 Report No.: FC09-014 This report contains a total of 122 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. The results in this report apply only to the items tested, as identified herein. Page 2 of 122 Report No: FC09-014 TABLE OF CONTENTS Administrative Information .............................................................................................3 Approvals .........................................................................................................................3 Summary of Results .........................................................................................................4 Conditions During Testing ...............................................................................................4 FCC 15.31(m) Number Of Channels ...............................................................................4 FCC 15.33(a) Frequency Ranges Tested .........................................................................4 EUT Operating Frequency ...............................................................................................4 Equipment Under Test (EUT) Description ......................................................................5 Equipment Under Test .....................................................................................................5 Peripheral Devices ...........................................................................................................5 Report of Emissions Measurements.................................................................................6 Testing Parameters ...........................................................................................................6 FCC 15.31(e) - Voltage Variation ...................................................................................8 FCC 15.207 – AC Conducted Emissions .........................................................................11 FCC 15.247(a) – 20dB Bandwidth ..................................................................................25 FCC 15.247(a) – Frequency Separation ...........................................................................28 FCC 15.247(a) – Number of Hopping Channels .............................................................30 FCC 15.247(a) – Average Time of Occupancy ...............................................................32 FCC 15.247(b) – RF Power Output .................................................................................34 FCC 15.247(d) – Antenna Conducted Spurious Emissions .............................................38 FCC 15.247(d) – OATS Radiated Spurious Emissions ...................................................52 RSS-210 – 99% Bandwidth .............................................................................................120 Page 3 of 122 Report No: FC09-014 ADMINISTRATIVE INFORMATION DATE OF TEST: February 9-12, 2009 DATE OF RECEIPT: February 9, 2009 REPRESENTATIVE: Mike Thomas MANUFACTURER: Impinj, Inc. 701 N. 34th Street Seattle, WA 98103 TEST LOCATION: CKC Laboratories, Inc. 110 Olinda Place Brea, CA 92823 TEST METHOD: ANSI C63.4 (2003), RSS-210 Issue 7 and RSS GEN Issue 2 PURPOSE OF TEST: To perform the testing of the RFID Reader, IPJ-REV with the requirements for FCC Part 15 Subpart C Sections 15.207 & 15.247and RSS-210 devices. APPROVALS QUALITY ASSURANCE: TEST PERSONNEL: Steve Behm, Director of Engineering Services Armando Del Angel, Test Engineer Donald Jones, Senior EMC Engineer / Lab Manager Page 4 of 122 Report No: FC09-014 SUMMARY OF RESULTS Test Specification Results Voltage Variation FCC Part 15.31(e) Pass Conducted Emissions FCC Part 15.207 Pass 20dB Bandwidth FCC Part 15.247(a) Pass Frequency Separation FCC Part 15.247(a) Pass Number of Hopping Channels FCC Part 15.247(a) Pass Average Time of Occupancy FCC Part 15.247(a) Pass RF Power Output FCC Part 15.247(b) Pass Antenna Conducted Spurious Emissions FCC Part 15.247(d) Pass OATS Spurious Emissions FCC Part 15.209/15.247(d) Pass Bandedge Pass 99% Bandwidth RSS-210 Issue 7 and RSS GEN Issue 2 Pass CONDITIONS DURING TESTING No modifications to the EUT were necessary during testing. FCC 15.31(m) Number Of Channels This device was tested on three channels. FCC 15.33(a) Frequency Ranges Tested 15.207 Conducted Emissions: 150 kHz – 30 MHz 15.209/15.247 Radiated Emissions: 9 kHz – 19 GHz EUT Operating Frequency The EUT was operating in the 902-928 MHz band. Page 5 of 122 Report No: FC09-014 EQUIPMENT UNDER TEST (EUT) DESCRIPTION The customer declares the EUT tested by CKC Laboratories was representative of a production unit. EQUIPMENT UNDER TEST Circular Patch Antenna Manuf: Cushcraft Model: S90289CLJ Serial: 092436 RFID Reader Manuf: Impinj Inc. Model: IPJ-REV Serial: 940-08-21-0006 AC/DC Adaptor Manuf: CUI Model: DSA-60W-20 Serial: ETS240250UC-P11P-DB Antenna Cable Manuf: Manhattan/CDT Model: M4213 Serial: 1354 E12091 Mini-Guardrail Manuf: Impinj Inc. Model: IPJ-A0303-0000E Serial: 0069 Brickyard Antenna Manuf: CSL Model: CS777-2 Serial: V25078 EP00090 Guardwall Antenna Manuf: Impinj Inc. Model: IPJ-A0402-USA Serial: 0116 PERIPHERAL DEVICES The EUT was tested with the following peripheral device(s): Wireless G Router Manuf: Belkin Model: F5D7230-4 Serial: 2028723009696 Laptop Computer Manuf: Dell Model: Latitude Serial: 6497402833 Switch POE Manuf: NETGEAR Model: FS108P Serial: 1DL1863H0073E Page 6 of 122 Report No: FC09-014 REPORT OF EMISSIONS MEASUR…

Text truncated - open the document above for the full version.

This report contains a total of 90 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. Impinj, Inc. ADDENDUM TEST REPORT FOR 90557‐6 RFID Integrated Reader, IPJR640 Tested To The Following Standards: FCC Part 15 Subpart C Sections 15.207 & 15.247 and RSS‐210 Version 7 Report No.: 90557‐6A Date of issue: May 19, 2010 TESTING CERT #803.01, 803.02, 803.05, 803.06 This test report bears the accreditation symbol indicating that the testing performed herein meets the test and reporting requirements of ISO/IEC 17025 under the applicable scope of EMC testing for CKC Laboratories, Inc. We strive to create long‐term, trust based relationships by providing sound, adaptive, customer first testing services. We embrace each of our customers’ unique EMC challenges, not as an interruption to set processes, but rather as the reason we are in business. Page 2of 90 Report No.: 90557‐6A TABLE OF CONTENTS Administrative Information ........................................................................................................................ 3 Test Report Information .......................................................................................................................................... 3 Revision History ....................................................................................................................................................... 3 Report Authorization ............................................................................................................................................... 3 Test Facility Information .......................................................................................................................................... 4 Site Registration & Accreditation Information ........................................................................................................ 4 Summary of Results ................................................................................................................................................. 5 Conditions During Testing ....................................................................................................................................... 5 Equipment Under Test ............................................................................................................................................. 6 Peripheral Devices ................................................................................................................................................... 6 FCC Part 15 Subpart C ................................................................................................................................. 7 Temperature And Humidity During Testing............................................................................................................. 7 15.33(a) Frequency Ranges Tested .......................................................................................................................... 7 15.203 Antenna Requirements ................................................................................................................................ 7 EUT Operating Frequency ........................................................................................................................................ 7 15.207 AC Conducted Emissions.............................................................................................................................. 8 15.247(a)(1)(i) 20 dB Bandwidth ........................................................................................................................... 22 15.247(b)(1) Maximum Peak Power ...................................................................................................................... 26 15.247(d) RF Conducted Spurious Emissions ......................................................................................................... 29 15.247(d) RF Radiated Spurious Emissions ............................................................................................................ 32 RSS‐210 99% Bandwidth ........................................................................................................................................ 85 Supplemental Information ........................................................................................................................ 89 Measurement Uncertainty .................................................................................................................................... 89 Emissions Test Details ............................................................................................................................................ 89 Page 3of 90 Report No.: 90557‐6A ADMINISTRATIVE INFORMATION Test Report Information REPORT PREPARED FOR: REPORT PREPARED BY: Impinj, Inc. 701 N. 34th St. Seattle, WA 98103 Joyce Walker CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 Representative: Bill Ashley Project Number: 90557 Customer Reference Number: 102475 DATE OF EQUIPMENT RECEIPT: April21, 2010 DATE(S) OF TESTING: April21‐22, 2010 Revision History Original: Test of the RFID Integrated Reader, IPJR640 to FCC Part 15 Subpart C Sections 15.207 & 15.247. Addendum A: Added a Laptop Computer and USB Hub to Peripheral sections, added better definition on the connections, cable type and operational mode in the test conditions, replaced plots with revised distance correction factor and antenna polarity, replaced bandedge compliance data/plots and peak power data/plots. Report Authorization The test data contained in this report documents the observed testing parameters pertaining to and are relevant for only the sample equipment tested in the agreed upon operational mode(s) and configuration(s) as identified herein. Compliance assessment remains the client’s responsibility. This report may not be us…

Text truncated - open the document above for the full version.

Page 1 of 19 Report No: FC09-014A TESTING CERT #803.01, 803.02, 803.05, 803.06 ADDENDUM TO IMPINJ INC. TEST REPORT FC09-014 FOR THE RFID READER, IPJ-REV FCC PART 15 SUBPART C SECTION 15.247 AND RSS-210 ISSUE 7 TESTING DATE OF ISSUE: AUGUST 12, 2009 PREPARED FOR: Impinj Inc. 701 N. 34th Street Seattle, WA 98103 PREPARED BY: Mary Ellen Clayton CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 P.O. No.: W.O. No.: 101439 89640 Date of test: July 23, 2009 Report No.: FC09-014A This report contains a total of 19 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. The results in this report apply only to the items tested, as identified herein. Page 2 of 19 Report No: FC09-014A TABLE OF CONTENTS Administrative Information .............................................................................................3 Approvals .........................................................................................................................3 Summary of Results .........................................................................................................4 Conditions During Testing ...............................................................................................4 Equipment Under Test (EUT) Description ......................................................................4 Equipment Under Test .....................................................................................................4 Peripheral Devices ...........................................................................................................4 Measurement Uncertainties .............................................................................................5 Report of Emissions Measurements.................................................................................5 Testing Parameters ...............................................................................................5 FCC 15.247(a) – Number of Hopping Channels .................................................7 FCC 15.247(a) – Average Time of Occupancy ...................................................11 RSS-210 – 99% Bandwidth .................................................................................16 Page 3 of 19 Report No: FC09-014A ADMINISTRATIVE INFORMATION DATE OF TEST: July 23, 2009 DATE OF RECEIPT: July 23, 2009 REPRESENTATIVE: Bill Ashley MANUFACTURER: Impinj Inc. 701 N. 34th Street Seattle, WA 98103 TEST LOCATION: CKC Laboratories, Inc. 22116 23rd Drive S.E., Suite A Bothell, WA 98021-4413 TEST METHOD: ANSI C63.4 (2003), RSS-210 Issue 7 and RSS GEN Issue 2 PURPOSE OF TEST: Original Report: To perform the testing of the RFID Reader, IPJ-REV with the requirements for FCC Part 15 Subpart C Sections 15.207 & 15.247and RSS-210 devices. Addendum A: To re-test the RFID Reader, IPJ-REV with the requirements for FCC Part 15 Subpart C Sections 15.247 and RSS-210 due to a firmware change to add reduced power channels. APPROVALS Steve Behm, Director of Engineering Services QUALITY ASSURANCE: TEST PERSONNEL: Donald Jones, Senior EMC Engineer / Lab Manager Armando Del Angel, Test Engineer Page 4 of 19 Report No: FC09-014A SUMMARY OF RESULTS Test Specification/Method Results Average Time of Occupancy FCC Part 15.247(a) Pass Number of Hopping Channels FCC Part 15.247(a) Pass 99% Bandwidth RSS-210 Issue 7 and RSS GEN Issue 2 Pass Site File No. FCC 318736 IC 3082C-1 CONDITIONS DURING TESTING No modifications to the EUT were necessary during testing. EQUIPMENT UNDER TEST (EUT) DESCRIPTION The customer declares the EUT tested by CKC Laboratories was representative of a production unit. EQUIPMENT UNDER TEST RFID Reader Manuf: Impinj Inc. Model: IPJ-REV Serial: 37009250045 PERIPHERAL DEVICES The EUT was tested with the following peripheral device(s): Router Manuf: Belkin Model: F5D7230-4 Serial: NA Laptop Manuf: Dell Model: Latitude 0026 Serial: NA Page 5 of 19 Report No: FC09-014A MEASUREMENT UNCERTAINTIES Uncertainty Value Parameter 4.73 dB Radiated Emissions 3.34 dB Mains Conducted Emissions 3.30 dB Disturbance Power The reported measurement uncertainties are calculated based on the worst case of all laboratory environments from CKC Laboratories, Inc. test sites. Only those parameters which require estimation of measurement uncertainty are reported. The reported worst case measurement uncertainty is less than the maximum values derived in CISPR 16-4-2. Reported uncertainties represent expanded uncertainties expressed at approximately the 95% confidence level using a coverage factor of k=2. Compliance is deemed to occur provided measurements are below the specified limits. REPORT OF EMISSIONS MEA…

Text truncated - open the document above for the full version.