TYLWS3NOutdoor Siren

Wireless Solar Siren with Strobe, WS-30S INTRODUCTION The WS-30S is a wireless solar siren with strobe dedicated for LS-30 alarm system. With special designed strobe magnifier, viewing angle and flashing pattern, it provides the users with a fresh experience. The WS-30S is powered by a solar panel which charges the internal battery. When the battery is fully charged, the WS-30S can work for one month without sunshine. With built in transmitter and receiver, it sends heartbeat signal once an hour, if the LS-30 Base Unit fails to receive this signal in the preset supervision time, it will issue a warning message. INITIAL POWER-UP Please note the internal rechargeable battery is not fully charged when you receive the WS-30S. You have to charge it for minimum 12 hours, (but NOT over 24 hours) first. The method as below, 1. turn on the battery switch, refer to Fig 2 2. either connect a 15VDC power adapter (supplied with LS-30), or connecting the supplied COM1 cable to the COM1 socket of a LS-30 which is powered, refer to Fig. 2. PROGRAMMING 1. Enroll the LS-30 Base Unit ID in the WS-30S, steps as below, A). Keep the WS-30S close to the LS-30 Base Unit for convenient operation. Enter the “Installer Mode” on the Base Unit and select \Set Siren\ Siren/Relay Test then wait. B). Turn on the WS-30S battery switch from off state. The WS-30S LED would light up C). Press the “YES” button (for Siren/Relay Test) on the Base Unit within 30 seconds. The Base Unit would transmit its RF ID and be enrolled in the WS-30S. However you can also program this through a PC with the supplied software. Important Note: If there is strong light shinning on the solar panel, it would produce a voltage to the internal PCB, so that the microprocessor on the PCB can’t be reset when the battery switch is turned on. Under such a condition, please turn the solar panel side down for a few seconds, and then turn on the battery switch. 2. Enroll the WS-30S ID in the LS-30 Base Unit, steps as below, A). Enter the “Installer Mode” on the Base Unit and select \Set Device\ Enroll Device\ Burglar Sensor\ Enter Zone No. B) Use a magnet (not supplied, but you can use the magnet for TX-3DS Door Sensor) to approach the right-bottom corner of the WS-30S, refer to Fig. 3. The WS-30S would emit its RF ID to be enrolled in the LS-30 Base Unit. C). The LS-30 LCD would show “Enroll OK” if action is correct. Likewise, you can also program this through a PC with the supplied software. Remark: When you put a magnet near the right-bottom corner of the WS-30S, it will generate a chirp and emit RF signal for test/enrolling. This action can also be used for RF check, refer to “Master Mode\ Device Test” of LS-30 manual. 3. If necessary, you can change the alarm time of the WS-30S by entering the desired time on the LS-30 Base Unit, under \Installer Mode\ Set Timer\ Set Remote Siren Time. LOCATION The WS-30S should be mounted outside the building and in a position where it can be clearly visible and at a height (3~5 meters above the ground) that is relatively difficult for an intruder to access. The WS-30S is built in radio transmitter and receiver which can be affected by the presence of metallic objects in the vicinity. Therefore, please keep the WS-30S minimum 30 cm away from any metalwork. Important Note: It takes 30 hours to fully charge the battery of the WS-30S under direct sunshine. To provide the maximum amount of sunlight to the solar panel of WS-30S, it’s strongly recommended to mount the WS-30S as below: 1).On the wall facing south for the user lives in the northern hemisphere and above the line of “Tropic of Cancer” (23.5°North). 2).On the wall facing north for the user lives in the southern hemisphere and below the line of “Tropic of Capricorn” (23.5°South). 3).On a wall easterly or westerly for the user can’t find a suitable location as above or lives in between of the 23.5°North and 23.5°South. Fig.1 Fig.2 Power Socket COM1 Socket Put a magnet closely to the right-bottom corner to activate RF transmission. Fig.3 Battery Switch Shadows cast by neighboring walls, trees and roof overhangs should be avoided. Besides, the sun is lower in the sky in winter, the winter shadow should be avoided too where possible. INSTALLATION AND TEST 1. Remove external power adapter or COM1 cable (if any) from the WS-30S, and turn off the battery switch. 2. Release the mounting bracket from the back side of the WS-30S by pulling the bracket downward from the case. 3. Use the mounting bracket as a template, hold it against the wall where the WS-30S is to be mounted, and mark the positions of the three screw holes. Drill three 6mm (1/4in.) holes 1 inch deep. Insert the supplied wall plugs and attach the bracket to the wall with the screws. 4. Turn on the battery switch. Use the supplied screw (4mm) to fix the WS-30S on the bracket, refer to Fig 4. Then put the plastic cap on the cavity of the top cover. 5. It’s a must to test RF range after installation , steps as below. A).On the LS-30 Base Unit, entering “Installer Mode” and select \Set Siren\ Siren/Relay Test then press the “YES” button, which will trigger the WS-30S to generate a chirp if everything is correct. B).Use a magnet to approach the right-bottom corner of the WS-30S, you will hear a chirp from the WS-30S and a beep from the LS-30 Base Unit if the distance is OK. Remark: If the WS-30S is removed from the bracket, or the housing is opened, the internal tamper switch would activate the siren for 5 minutes, or until the WS-30S is mounted on the bracket again. Meanwhile, the WS-30S would send a RF signal of tamper detection to the LS-30 Base Unit. INDICATION The reaction of the light and sound of the WS-30S varies with the operation or alarm state as below, -Power ON and code enroll: The WS-30S enters ENROLL state for 30 seconds automatically when the power is applied. Light stays ON continuously, until the WS-30S learns a new code (2 chirps), or a 30-second timeout expires (one chirp, no new code lear…

Text truncated - open the document above for the full version.

V 25 FCC ID: TYLWS3N Device Name: Solar Strobe Siren Model No.: WS-30S Date: 6/26/2013 Federal Communications Commission To whom it may concern: I, the undersigned, hereby authorize Mr . James Cheng / Application Examiner of ELECTRONICS TESTING CENTER, TAIWAN and hereafter referred to as ETC, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Mr. James Cheng of ETC on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ELECTRONICS TESTING CENTER, TAIWAN as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product  compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, By: By: Kevin Wang (Signature) (Printed) Title : Marketing Manager Applicant : Scientech Electronics Co., Ltd. Address : 4F No. 501-17, Zhong Zheng Rd., Xin Dian Dist., New Taipei City 23148, Taiwan Tel : 886-2-22183085 Fax: 886-2-22187380

V 25 FCC ID: TYLWS3N Device Name: Solar Strobe Siren Model No.: WS-30S Date: 6/26/2013 Federal Communications Commission Dear Sir: Pursuant to Section 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Descriptions The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. By: By: Kevin Wang (Signature) (Printed) Title : Marketing Manager Applicant : Scientech Electronics Co., Ltd. Address : 4F No. 501-17, Zhong Zheng Rd., Xin Dian Dist., New Taipei City 23148, Taiwan Tel : 886-2-22183085 Fax: 886-2-22187380

FCC ID.: TYLWS3N Page A1 of A1 ETC Report No.: 12-12-MAS-296-16 ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Outside view 1 of EUT 2. Outside view 2 of EUT

WS-30S Model: WS-30S FCC ID: TYLWS3N This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made in Taiwan 40mm 28mm

FCC ID.: TYLWS3N Page B1 of B7 ETC Report No.: 12-12-MAS-296-16 ANNEX B: INTERNAL CONSTRUCTION PHOTOS OF EUT 1. Inside View 1 of EUT 2. Inside View 2 of EUT FCC ID.: TYLWS3N Page B2 of B7 ETC Report No.: 12-12-MAS-296-16 3. Inside View 3 of EUT 4. Inside View 4 of EUT FCC ID.: TYLWS3N Page B3 of B7 ETC Report No.: 12-12-MAS-296-16 5. Battery 6. Antenna FCC ID.: TYLWS3N Page B4 of B7 ETC Report No.: 12-12-MAS-296-16 7. Front view of PCB1 (433MHz RX) 8. Rear view of PCB1 (433MHz RX) FCC ID.: TYLWS3N Page B5 of B7 ETC Report No.: 12-12-MAS-296-16 Antenna A 433MHz Receive r Antenna A 433MHz Receive r 9. Front view of PCB2 10. Rear view of PCB2 Antenna A 433MHz Receive r Antenna B 915MHz Transmitte r Antenna B 915MHz Transmitte r Antenna A 433MHz Receive r FCC ID.: TYLWS3N Page B6 of B7 ETC Report No.: 12-12-MAS-296-16 11. Module (915MHz TX) 12. Module (915MHz TX) FCC ID.: TYLWS3N Page B7 of B7 ETC Report No.: 12-12-MAS-296-16 13. Module (915MHz TX)

FCC ID.: TYLWS3N Sheet 1 of 21 Sheets ETC Report No. : 12-12-MAS-296-16 Rev. No 1.0 CONFORMANCE TEST REPORT FOR FCC 47 CFR, Part 15 Subpart C Report No.: 12-12-MAS-296-16 Client: Scientech Electronics Co., Ltd. Product: Outdoor Siren Model: WS-30S Manufacturer/supplier: Scientech Electronics Co., Ltd. Date test item received: 2012/11/21 Date test campaign completed: 2013/05/17 Date of issue: 2013/05/17 The test result only corresponds to the tested sample. It is not permitted to copy this report, in part or in full, without the permission of the test laboratory. Total number of pages of this test report: 21 pages Total number of pages of photos: External photos 1 pages Internal photos 7 pages Setup photos 3 pages Prepared By Technical Acceptance By Approved By Phillip Luo Perry Lin James Cheng ELECTRONICS TESTING CENTER, TAIWAN NO.8, LANE 29, WENMING RD., LESHAN TSUEN, GUISHAN SHIANG, TAOYUAN COUNTY, TAIWAN 33383, R.O.C. TEL: (03) 3276170~4 INT: +886-3-3276170~4 FAX: (03) 3276188 INT: +886-3-3276188 FCC ID.: TYLWS3N Sheet 2 of 21 Sheets ETC Report No. : 12-12-MAS-296-16 Rev. No 1.0 Client : Scientech Electronics Co., Ltd. Address : 4F, No. 501-17, Zhong Zheng Rd., Xin Dian Dist., New Taipei City 23148, Taiwan Manufacturer : Scientech Electronics Co., Ltd. Address : 4F, No. 501-17, Zhong Zheng Rd., Xin Dian Dist., New Taipei City 23148, Taiwan EUT : Outdoor Siren Trade name : ---- Model No. : WS-30S Comment Issues : (1) The report also apply to model: WS-30A (2) The multiple listing recognized without test basis is according to information supplied by manufacturer. A detail documentation of the above models must be verified by legal right organization for the EMC characteristic with relation to the subject model. Power Source : Adapter : Input: 100-240Vac, 50/60Hz, 0.28A Output: 15Vdc, 0.8A Regulations applied : FCC 47 CFR, Part 15 Subpart C The testing described in this report has been carried out to the best of our knowledge and ability, and our responsibility is limited to the exercise of reasonable care. This certification is not intended to believe the sellers from their legal and/or contractual obligations. The compliance test is only certified for the test equipment and the results of the testing report relate only to the item tested. The compliance test of this report was conducted in accordance with the appropriate standards. It’s not intention to assure the quality and performance of the product. This report shall not be reproduced except in full, without the approval of ETC. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. Laboratory Introduction: Electronics Testing Center, Taiwan is recognized, filed and mutual recognition arrangement as following:  ISO9001: TüV Product Service  ISO/IEC 17025: BSMI, TAF, NCC, NVLAP, ILAC MRA, UL, Compliance  Filing: FCC, Industry Canada, VCCI  MRA: Australia, Hong Kong, New Zealand, Singapore, USA, Japan, Korea, China, APLAC through TAF  FCC Registration Number: 91095, 392735, 278818  Industry Canada Site Registration Number: IC 2949A-2 NVLAP Lab Code 200133-0 FCC ID.: TYLWS3N Sheet 3 of 21 Sheets ETC Report No. : 12-12-MAS-296-16 Rev. No 1.0 Table of Contents Page 1. GENERAL INFORMATION ...................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION.................................................................................................................................................. 4 1.2 CHARACTERISTICS OF DEVICE:....................................................................................................................................... 4 1.3 TEST METHODOLOGY..................................................................................................................................................... 4 1.4 TEST FACILITY............................................................................................................................................................... 4 2. DEFINITION AND LIMITS ....................................................................................................................................... 5 2.1 DEFINITION.................................................................................................................................................................... 5 2.2 RESTRICTED BANDS OF OPERATION...............................................................................................................................6 2.3 LIMITATION.................................................................................................................................................................... 6 2.4 LABELING REQUIREMENT............................................................................................................................................... 8 2.5 USER INFORMATION....................................................................................................................................................... 8 3. SYSTEM TEST CONFIGURATION .......................................................................................................................... 9 3.1 DEVICES FOR TESTED SYSTEM....................................................................................................................................... 9 4. RADIATED EMISSION MEASUREMENT ........................................................................................................... 10 4.1 APPLICABLE STANDARD............................................................................................................................................... 10 4.2 MEASUREMENT PROCEDURE........................................................................................................................................ 10 4.3 TEST DATA.............................................................…

Text truncated - open the document above for the full version.

FCC ID.: TYLWS3N Sheet 1 of 3 Sheets ETC Report No.: 12-12-MAS-296-16 Photos of Radiation Measuring Setup x-axis FCC ID.: TYLWS3N Sheet 2 of 3 Sheets ETC Report No.: 12-12-MAS-296-16 y-axis z-axis FCC ID.: TYLWS3N Sheet 3 of 3 Sheets ETC Report No.: 12-12-MAS-296-16 Photos of Conduction Measuring Setup