
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Resolution RE103 Wireless Panic Transmitter User and Installation Instructions Introduction The RE103 Wireless Panic Transmitter is a wireless 1-button transmitter for security system use. Typical use of this device is for sending a panic alarm to the system. The transmitter is shown in Figure 1. Figure 1: RE103 Successful activation of the transmitter is indicated by a short, bright LED flash. The Wireless Panic Transmitter uses a small lithium coin cell battery, designed to provide long battery life. Transmitter Programming Each RE103 Wireless Panic Transmitter is shipped with a unique serial number pre-programmed into the transmitter. Upon installation, the RE103 must be programmed into the security control panel. The control panel's documentation should be consulted for full instructions. Specifications Dimensions: 1.125 x 1.5 x 0.5” RF transmission frequency: 319.5MHz Operating Temperature: 10º to 120ºF (-12º to 49ºC) Battery Type: CR2032 Lithium Coin Cell FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference. 2.This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the Resolution Engineering, Inc could void the user's authority to operate this equipment. FCC ID: U5X-RE103 IC Notice This product meets the applicable Industry Canada technical specifications/Le présent materiel est conforme aux specifications techniques applicables d’Industrie Canada. IC: 8310A-RE103
May 24, 2010 RE: U5X-RE103 Confidentiality To Whom It May Concern: The following information is to be held confidential pursuant of 47 CFR Part 0 ァ0.459 and Section 552(b)(4) of the Freedom of Information Act, because the information provided contains trade secrets and is proprietary. If made public, the information might be used to our disadvantage as in the market place. lSchematics lTechnical Product Description/Operational Description lBlock Diagram Sincerely, Paul Saldin Vice President Resolution Products, Inc.
Exhibit A RE103 External Photo Back
Exhibit B RE103 External Photo Front
Exhibit A RE103 External Photo Back
Exhibit C RE103 Internal Photo Back
Exhibit D RE103 Internal Photo Front
Resolution Products, Inc. Wireless Panic Transmitter FCC ID: U5X-RE103 Certification Test Report May 26, 2010 U5X-RE103 Resolution Products, Inc.05/26/10Page 1 of 9 Test Report 226 Locust Street, Suite 4 Hudson, WI 54016 Contents 1. Introduction ................................................................................................................................................................. 3 2. Statement of Compliance ............................................................................................................................................ 3 2.1. FCC Part 2 §2.907 ................................................................................................................................................ 3 2.2. FCC Part 2 §2.911 ................................................................................................................................................ 3 2.3. FCC Part 2 §2.913 ................................................................................................................................................ 3 2.4. FCC Part 2 §2.915 ................................................................................................................................................ 3 2.5. FCC Part 2 §2.925 ................................................................................................................................................ 3 2.6. FCC Part 2 §2.943, 2.945 .................................................................................................................................... 3 2.7. FCC Part 2 §2.947 ................................................................................................................................................ 4 2.8. FCC Part 2 §2.948 ................................................................................................................................................ 4 2.9. FCC Part 2 §2.1033 .............................................................................................................................................. 5 3. Discussion of Laboratory Measurements and Rules Compliance ............................................................................... 6 3.1. FCC Part 15 §15.231(a)(1) .................................................................................................................................. 6 3.2. FCC Part 15 §15.231(a)(3) .................................................................................................................................. 6 3.3. FCC Part 15 §15.231(a)(4) .................................................................................................................................. 7 3.4. FCC Part 15 §15.231(a)(5) .................................................................................................................................. 7 3.5. FCC Part 15 §15.231(b) ....................................................................................................................................... 7 3.5.1. Raw Field Strength Limits ............................................................................................................................ 7 3.5.2. Duty Cycle Correction Factor and Resulting Limits ..................................................................................... 8 3.5.3. Measured Radiated Field Strength Data ....................................................................................................... 8 3.6. FCC Part 15 §15.231(c) ....................................................................................................................................... 9 U5X-RE103 Resolution Products, Inc.05/26/10Page 2 of 9 Test Report 226 Locust Street, Suite 4 Hudson, WI 54016 1.Introduction This device is a handheld wireless transmitter for use in a wireless security system. The unit is powered by a 3V lithium battery. The transmitter is centered at 319.5MHz and is controlled by a SAW resonator. The device measures 1.125 x 1.5 x 0.5” and weighs approximately half an ounce. This transmitter is manually activated via a pushbutton switch. Transmission packets are sent by the device upon valid keypress activation. These packets are 20ms in length and are sent with a random spacing of 170ms to 330ms. The device will continue sending packets for the pendency of the alarm condition, as allowed, as long as the switch is held down by the user. Upon release of the switch, 12 packets are sent to signal the release. The unit then goes into sleep mode and will not transmit again until another valid keypress is detected. Three supervisory packets are sent by the device every hour, with the same random spacing described above. Certification is requested under FCC Rules, Part 15, Subpart C, Paragraph 15.231. 2.Statement of Compliance Specific sections of FCC Rules Part 2 that require information or listing are given below. 2.1.FCC Part 2 §2.907 This is an application for certification of original equipment 2.2.FCC Part 2 §2.911 a)This application has been filed electronically using form 731. b)All required information has been supplied in this application and its attachments. c)This application has been electronically signed by an officer of Resolution Products, Inc. d)The technical test data has been signed by the agency performing the testing. e)Signature supplied in appropriate block on form 731. f)Processing fee has been paid by credit card. g)Signatures have been supplied electronically. 2.3.FCC Part 2 §2.913 a)This application has been filed electronically. b)Appropriate fees have been filed electronically. c)Equipment samples shall be supplied as requested. 2.4.FCC Part 2 §2.915 We are requesting a grant of certification. This application shows compliance with the technical standards. 2.5.FCC Part 2 §2.925 A label shall be affixed to each piece of equipment, showing the FCC identifier. The label shall read “FCC ID: U5X- RE103”. See Exhibit…
Text truncated - open the document above for the full version.