U6A-WU306N11n USB Dongle

1 User Guide of WU306n Installing the software of USB Adapter................................................2 Configuring your wireless network (with Wireless Utility)......5 Configuring your wireless network (with Microsoft Zero Configuration Tool).......................................................................................... 11 Wi-Fi Protect Setup (WPS)..........................................................................13 Pin Input Config (PIN)...........................................................................14 Push Button (PBC)...................................................................................18 Radio Off.................................................................................................................20 Disable Adapter..................................................................................................22 Uninstalling the software.............................................................................23 Wireless Zero Configuration Troubleshooting.................................25 Federal Communication Commission Interference Statement ....................................30 2 Installing the software of USB Adapter 1. Select the setup file to install. The setup program will detect user’s language automatically. 2. The setup program will install the driver and utility to computer. Please click the “Next” button to continue. 3. The setup program is ready to begin installation. Please click the “Install” button. 3 4. The software installation should begin. This may take a few minutes. 5. Once the installation success, click “Yes” to restart your system (recommended). Otherwise, click “No” to restart your system later. 4 6. Once the installation complete, you may now configure your wireless network. 5 Configuring your wireless network (with Wireless Utility) 1. Windows XP users, if you chose “Microsoft Zero Configuration Tool” during the software installation please skip to page 11. 2. Double click on the computer with wireless signal icon in your taskbar or the shortcut icon on the desktop. 3. It should pop up the Wireless Utility window. And then utility shows the connecting wireless network that connected automatically or was the default network in profile. 6 4. Click the “Available Network” tab to the wireless network surveying page. Click the “Refresh” button to scan the area for wireless network(s). Once the scan completed, select the desired wireless network from the list and double click it or click the “Add to Profile” button. 7 5. It should pop up the wireless Network Properties window. If you do not have any wireless security (WEP, WPA, WPA2, and etc.) set on your wireless network, simply click the “OK” button and skip to step7. If you do have wireless securities on your wireless network, configure the security setting in “Wireless network security” column. 8 6. Set your wireless securities settings, when it completed, click the “OK” button. Select the Network Authentication and Data encryption to set the encryption type. - If you have WEP, typically you select the format and enter your WEP key below the Data encryption. - If you have WPA-PSK or WPA2-PSK, typically you only enter your key in the “Network Key” and type again to confirm it. - If you have 802.1x configure, typically you only configure your setting in 802.1x configure column. 9 7. After connected to wireless network, utility will back to “General” page and show the wireless network status. Once the wireless network connected successfully, the Network Address will show the WU306n has gotten the IP address from DHCP. 10 8. Click the “Profile” tab to check the profile page. The wireless network configuration has added in Available Profile(s). It could remove, edit, duplicate and set default the profiles in this page. 11 Configuring your wireless network (with Microsoft Zero Configuration Tool) Warning: Due to security reasons, we strongly recommend updating Windows XP to service pack 2 and above, if you have not done so. If you do not wish to update, please follow the following steps to change the configuration tool between wireless utility and Microsoft Zero configuration tool. 1. Please open the wireless utility. And then enable the “Windows Zero Config” as configuration utility. After enabling the “Windows Zero Config” will pop out a message box, click the “ok” button to continue. 12 2. Once using Microsoft Zero Configuration Tool to configure wireless network, Wireless Utility will be can not configure. 13 Wi-Fi Protect Setup (WPS) WPS is an easy and secure setup solution for Wi-Fi network. Please click the Wi-Fi Protect Setup tab. WU306n has two methods, PIN (Pin Input Config) and PBC (Push Button Config), to setup the network. 14 Pin Input Config (PIN) 1. Click on the “Pin Input Config (PIN)” button, and then it should pop up a message box. If you want to connect to a specific AP, please click the “Yes” button. Or please click the “No” button to continue and skip to step3. Note: Every time you click the tab to change the page, the PIN code will be changed. 15 2. Select the specific AP which you want to connect. If you can not find the WPS AP in this page, please click the “Refresh” button. And then click the “Select” button. 16 3. WU306n is waiting for the AP to establish the connection. And then enter the PIN code into the AP that you want to connect. For example, the AP uses BR360n to be the connecting device. Enter the PIN code into client pin number and then clicks the “Start PIN” button. Note: The PIN function in AP should be started before the WPS setup in WU306n times out. 17 4. Once the WPS connected successfully, wireless utility will show the connection status. 18 Push Button (PBC) 1. Click on the “Push Button Config (PBC)” button. Note: The PBC button can click the visual button on the page or push the physical button on AP. 19 2. WU306n is waiting for the other AP to start the PBC function. The other AP starts the PBC function …

Text truncated - open the document above for the full version.

Chris Harvey From:[email protected] Sent:Monday, December 21, 2009 2:12 AM To:[email protected] Cc:[email protected]; [email protected]; [email protected]; [email protected] Subject:回信: E-Top Network Technology Inc., FCC ID: U6A-WU306N, Assessment NO.: AN09T9922, Notice#1-->Updated(981221) Attachments:WU306n_User Manual(981221).pdf; WU360n_Report(FCC 15C-1)981221.pdf; WU306n_Description of Operation(981221).pdf; WU306n_External Photo(981221).pdf; WU306n_Internal Photo(981221).pdf Page 1 of 2 12/21/2009 Dear Chris: Thank you for your notice,please see my belowing reply and find the updated files (981221). And if there is no any problems,cusotmer needs to get the certificate before on 12/22/2009 (Taiwan time)!! Please help and thank you for your support~ 寄件人: <[email protected]> 收件人: <[email protected]>, <[email protected]> 副本抄送: <[email protected]> 日期: 2009/12/16 上午 08:58 主旨: E-Top Network Technology Inc., FCC ID: U6A-WU306N, Assessment NO.: AN09T9922, Notice#1 Dear Daphne, You are listed as the Technical Contact for the above referenced TCB application. The following item(s) need(s) to be resolved before the review can be continued: 1. The manual states that a 20cm separation to users is required; however, the FCC policy on USB dongles requires the RF Exposure to be addressed using a 0.5 cm separation for typical notebook computer use. This device was tested for SAR at the required 0.5cm separation. Please revise the Users Manual RF Exposure statements to reflect that a minimum separation of 0.5cm is required. ANS:Please find the updated user manual(981221) of page 30. 2. Please note that the test report states that FCC Rule Part 15 from 2004 was used. Please ensure that this boiler plate is changed to reflect that the most recent FCC Rules are used (currently 2008 is still the most current). ANS:Please find the updated test report(981221) of page 1 & 4. 3., The Operational Description states that this is a 1x1 (1-Tx and 1-Rx) device. However the application also states that this uses both antennas for receive. Does this device operate as a 1x2 device, using both antennas as receive paths? NS:This device should be as a 1T X 2R device. Please find the updated Operational description (981221) & revised External & Internal photo(981221) which to showed the antenna location. The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e- mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. Best regards, Chris Harvey [email protected] ______________________________________________________________ This e-mail transmission is confidential and intended solely for being reviewed by the recipient(s) identified above. If you are not an identified recipient, please ensure that this communication remains confidential and promptly return it to the sender. Please contact immediately by phone (Tel: 886-2-2299-9720) for any problem with this transmission. Thank you for your attention. No virus found in this incoming message. Checked by AVG - www.avg.com Version: 9.0.717 / Virus Database: 270.14.115/2577 - Release Date: 12/20/09 14:35:00 Page 2 of 2 12/21/2009

!Compliance Certification Services Inc.!!!!!!!!!!Report No.Κ91012402 ! ! ! ! External Photo ( Model : WU306n) ! !Compliance Certification Services Inc.!!!!!!!!!!Report No.Κ91012402 ! ! ! ! ! !Compliance Certification Services Inc.!!!!!!!!!!Report No.Κ91012402 ! ! ! ! !

WU306n Back Diagram Label location FCC Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Marked in the user manual Model: WU306n 11n USB Dongle

!Compliance Certification Services Inc.!!!!!!!!!!Report No.Κ91012402 ! ! ! ! ! ! Internal Photo !Compliance Certification Services Inc.!!!!!!!!!!Report No.Κ91012402 ! ! ! ! ! ! !Compliance Certification Services Inc.!!!!!!!!!!Report No.Κ91012402 ! ! ! ! ! ! ! AntA AntB

E-Top Network Technology Inc. 1-1. GENERAL DESCRIPTION OF EUT & SPEC Antenna A (TX+RX) MANUFACTURER: Realtek Semiconductor Corp. MODEL ON: N/A FREQUENCY RANGE: 2.4G~2.5GHz, IMPEDANCE: 50Ω ANTENNA GIAN: 1.72 dBi ANTENNA MODEL: Printed PCB Antenna Antenna B (RX) MANUFACTURER: Realtek Semiconductor Corp. MODEL ON: N/A FREQUENCY RANGE: 2.4G~2.5GHz, IMPEDANCE: 50Ω ANTENNA GIAN: 0 dBi ANTENNA MODEL: Printed PCB Antenna

Date/Time:11/13/2009 09:55:23 AM Test Laboratory: Compliance Certification Services Inc. D2450V2 SN-728 Body DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:728 Communication System: CW2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; ı = 1.96 mho/m; İ r = 51.5; ȡ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: z Probe: EX3DV4 - SN3554; ConvF(5.80, 5.80, 5.80); z Sensor-Surface: 2.5mm (Mechanical Surface Detection) z Electronics: DAE4 Sn558; Calibrated: 7/17/2009 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Pin=250mW,d=10mm/Area Scan (6x6x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.3 mW/g Pin=250mW,d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 94.7 V/m; Power Drift = -0.028 dB Peak SAR (extrapolated) = 26.6 W/kg SAR(1 g) = 13 mW/g; SAR(10 g) = 6.11 mW/g Maximum value of SAR (measured) = 18.5 mW/g Pin=250mW,d=10mm/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 18.8 mW/g Page1 Page2 Date/Time:11/13/200911:13:32AM Test Laboratory: Compliance Certification Services Inc. 80211b Horizontal Down mode WU306n DUT: WU306n; Type: WU306n; Serial: N/A Communication System: IEEE 802.11b WLAN; Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; ı = 1.98 mho/m; İ r = 51.5; ȡ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: z Probe: EX3DV4 - SN3554; ConvF(5.80, 5.80, 5.80); z Sensor-Surface: 2.5mm (Mechanical Surface Detection) z Electronics: DAE4 Sn558; Calibrated: 7/17/2009 z Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 z Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 High CH Rate 1M/Area Scan (5x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.611 mW/g High CH Rate 1M/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 3.33 V/m; Power Drift = -0.060 dB Peak SAR (extrapolated) = 1.25 W/kg SAR(1 g) = 0.523 mW/g; SAR(10 g) = 0.195 mW/g Maximum value of SAR (measured) = 0.710 mW/g Page1 Page2 Date/Time:11/13/200911:46:54AM Test Laboratory: Compliance Certification Services Inc. 80211g Horizontal Down mode WU306n DUT: WU306n; Type: WU306n; Serial: N/A Communication System: IEEE 802.11g WLAN; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2437 MHz; ı = 1.95 mho/m; İ r = 51.5; ȡ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: z Probe: EX3DV4 - SN3554; ConvF(5.80, 5.80, 5.80); z Sensor-Surface: 2.5mm (Mechanical Surface Detection) z Electronics: DAE4 Sn558; Calibrated: 7/17/2009 z Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 z Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Middle CH Rate 6M/Area Scan (5x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.425 mW/g Middle CH Rate 6M/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 3.02 V/m; Power Drift = -0.053 dB Peak SAR (extrapolated) = 0.823 W/kg SAR(1 g) = 0.380 mW/g; SAR(10 g) = 0.133 mW/g Maximum value of SAR (measured) = 0.508 mW/g Page1 Page2 Date/Time:11/13/200912:11:57 PM Test Laboratory: Compliance Certification Services Inc. 80211g Horizontal Down mode WU306n HT20 DUT: WU306n; Type: WU306n; Serial: N/A Communication System: IEEE 802.11g WLAN HT20; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2437 MHz; ı = 1.95 mho/m; İ r = 51.5; ȡ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: z Probe: EX3DV4 - SN3554; ConvF(5.80, 5.80, 5.80); z Sensor-Surface: 2.5mm (Mechanical Surface Detection) z Electronics: DAE4 Sn558; Calibrated: 7/17/2009 z Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 z Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Middle CH Rate 6.5M/Area Scan (6x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.126 mW/g Middle CH Rate 6.5M/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 2.72 V/m; Power Drift = -0.082 dB Peak SAR (extrapolated) = 0.221 W/kg SAR(1 g) = 0.112 mW/g; SAR(10 g) = 0.067 mW/g Maximum value of SAR (measured) = 0.133 mW/g Page1 Page2 Date/Time:11/13/2009 12:56:00PM Test Laboratory: Compliance Certification Services Inc. 80211b Horizontal Up mode WU306n DUT: WU306n; Type: WU306n; Serial: N/A Communication System: IEEE 802.11b WLAN; Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; ı = 1.98 mho/m; İ r = 51.5; ȡ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: z Probe: EX3DV4 - SN3554; ConvF(5.80, 5.80, 5.80); z Sensor-Surface: 2.5mm (Mechanical Surface Detection) z Electronics: DAE4 Sn558; Calibrated: 7/17/2009 z Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 z Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 High CH Rate 1M/Area Scan (6x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.638 mW/g High CH Rate 1M/Zoom Scan (7x7x9)/Cube 0: Mea…

Text truncated - open the document above for the full version.

!!Compliance Certification Services Inc.!! Report No.Κ91012402-RP1 FCC IDΚU6A-WU306N Date of Issue: November 12, 2009 ! Qbhf!2! FCC 47 CFR PART 15 SUBPART C: 2008 AND ANSI C63.4: 2003 TEST REPORT For 11n USB Dongle Model Number: WU306n Brand Name: ETOP Issued for E-Top Network Technology Inc. No. 82, Gongye 2nd Rd., Tainan City 70955, Taiwan, R.O.C. Issued by Compliance Certification Services Inc. Tainan Lab. No. 8, Jiu Cheng Ling, Jiaokeng Village,Sinhua Township, Tainan Hsien 712, Taiwan R.O.C. TEL: 886-6-580-2201 FAX: 886-6-580-2202 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. Ltd. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document Total Page: 128 !!Compliance Certification Services Inc.!! Report No.Κ91012402-RP1 FCC IDΚU6A-WU306N Date of Issue: November 12, 2009 ! Qbhf!3! REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 November 12, 2009 Initial Issue ALL Leah Peng !!Compliance Certification Services Inc.!! Report No.Κ91012402-RP1 FCC IDΚU6A-WU306N Date of Issue: November 12, 2009 ! Qbhf!4! ! TABLE OF CONTENTS 1. TEST REPORT CERTIFICATION ................................................................................................ 4 2. EUT DESCRIPTION ...................................................................................................................... 5 2.1 DESCRIPTION OF EUT & POWER ......................................................................................................5 3. DESCRIPTION OF TEST MODES ............................................................................................... 7 4. TEST METHODOLOGY ............................................................................................................... 8 5. FACILITIES AND ACCREDITATIONS ...................................................................................... 8 5.1 FACILITIES.............................................................................................................................................8 5.2 EQUIPMENT ...........................................................................................................................................8 5.3 LABORATORY ACCREDITATIONS LISTINGS.................................................................................8 5.4 TABLE OF ACCREDITATIONS AND LISTINGS ...............................................................................9 6. CALIBRATION AND UNCERTAINTY....................................................................................... 10 6.1 MEASURING INSTRUMENT CALIBRATION....................................................................................10 6.2 MEASUREMENT UNCERTAINTY ......................................................................................................10 7. SETUP OF EQUIPMENT UNDER TEST ..................................................................................... 11 7.1 SETUP CONFIGURATION OF EUT .....................................................................................................11 7.2 SUPPORT EQUIPMENT ........................................................................................................................11 7.3 EUT OPERATING CONDITION............................................................................................................12 8. APPLICABLE LIMITS AND TEST RESULTS ............................................................................ 13 8.1 6DB BANDWIDTH .................................................................................................................................13 8.2 99% BANDWIDTH .................................................................................................................................24 8.3 MAXIMUM PEAK OUTPUT POWER ..................................................................................................34 8.4 MAXIMUM PERMISSIBLE EXPOSURE .............................................................................................46 8.5 POWER SPECTRAL DENSITY .............................................................................................................48 8.7 CONDUCTED SPURIOUS EMISSION .................................................................................................58 8.8 RADIATED EMISSIONS........................................................................................................................67 8.9 POWERLINE CONDUCTED EMISSIONS ...........................................................................................120 9. ANTENNA REQUIREMENT ........................................................................................................ 124 9.1 STANDARD APPLICABLE ...................................................................................................................124 9.2 ANTENNA CONNECTED CONSTRUCTION ......................................................................................124 APPENDIX SETUP PHOTOS ........................................................................................................... 125 !!Compliance Certification Services Inc.!! Report No.Κ91012402-RP1 FCC IDΚU6A-WU306N Date of Issue: November 12, 2009 ! Qbhf!5! 1. TEST REPORT CERTIFICATION Applicant Κ E-Top Network Technology Inc. Address Κ No. 82, Gongye 2nd Rd., Tainan City 70955, Taiwan, R.O.C. Manufacture Κ E-Top Network Technology Inc. Address Κ No. 82, Gongye 2nd Rd., Tainan City 70955, Taiwan, R.O.C. Equipment Under Test Κ 11n USB Dongle Model Number Κ WU306n Brand Name Κ ETOP Date of Test Κ October 16, 2009 ~ November 03, 2009 APPLICABLE STANDARD STANDARD TEST RESULT FCC Part 15 Subpart C : 2008 AND ANSI C63.4 : 2003 No non-compliance noted Approved by: Reviewed by: ! ! ! ! Jeter Wu Eric Yang Section Manager Senior Engineer Compliance Certification Services I…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.：91012402-RP1 FCC ID：U6A-WU306N Date of Issue: November 12, 2009 Page 125 APPENDIX SETUP PHOTOS RADIATED EMISSION MEASUREMENT SETUP Compliance Certification Services Inc. Report No.：91012402-RP1 FCC ID：U6A-WU306N Date of Issue: November 12, 2009 Page 126 RADIATED RF MEASUREMENT SETUP Compliance Certification Services Inc. Report No.：91012402-RP1 FCC ID：U6A-WU306N Date of Issue: November 12, 2009 Page 127 Compliance Certification Services Inc. Report No.：91012402-RP1 FCC ID：U6A-WU306N Date of Issue: November 12, 2009 Page 128 POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP End of report