U9R-W2CBW0015WLAN+Bluetooth Module

Wi2Wi, Inc. Rev.1.51 Data Sheet, WLAN-Bluetooth SiP – W2CBW0015 July 26th, 2012 The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorized in writing by Wi2Wi, Inc. Copyright © 2012 Wi2Wi, Inc. Page 1 of 25 Preliminary Product Datasheet Revision 1.51 July 26, 2012 Wi2Wi, Inc. Rev.1.51 Data Sheet, WLAN-Bluetooth SiP – W2CBW0015 July 26th, 2012 The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorized in writing by Wi2Wi, Inc. Copyright © 2012 Wi2Wi, Inc. Page 2 of 25 Table of Contents 1 General Description ........................................................................................................... 4 2 Features .............................................................................................................................. 4 3 System Description ............................................................................................................ 5 3.1 Block Diagram .......................................................................................................................... 5 3.2 Pad Description ........................................................................................................................ 5 4 Electrical Characteristics .................................................................................................. 8 5 WLAN External Host Interfaces .................................................................................... 11 5.1 SDIO Interface........................................................................................................................ 11 5.2 SDIO Protocol Timing Diagrams ............................................................................................ 12 6 Bluetooth Interfaces ........................................................................................................ 13 6.1 SDIO Interface........................................................................................................................ 13 6.2 PCM Interface ........................................................................................................................ 13 7 Antenna and Clock .......................................................................................................... 14 7.1 Wireless LAN.......................................................................................................................... 14 7.2 Bluetooth ................................................................................................................................ 14 8 WLAN Software Architecture ........................................................................................ 16 8.1 Host Processor ....................................................................................................................... 16 9 Reference Schematics ...................................................................................................... 17 10 Manufacturing Notes ....................................................................................................... 18 10.1 Physical SiP Dimensions and Pad Locations ........................................................................ 18 10.2 Physical Shield Dimensions ................................................................................................... 19 10.3 Shield Landing Pattern ......................................................................................................... 20 10.4 Tray Orientation ...................................................................................................................... 20 10.5 Tape and Reel Orientation ..................................................................................................... 22 10.6 Storage and Baking Instructions ............................................................................................ 23 10.7 Recommended Reflow Profile ................................................................................................ 23 11 Disclaimers ....................................................................................................................... 24 11.1 Data Sheet Status .................................................................................................................. 24 12 Ordering Information ................................................................................................... 24 12.1 Development Kit ..................................................................................................................... 24 13 Certifications .................................................................................................................... 25 14 References ......................................................................................................................... 25 14.1 Specifications ......................................................................................................................... 25 14.2 Trademarks, Patents and Licenses ....................................................................................... 25 Wi2Wi, Inc. Rev.1.51 Data Sheet, WLAN-Bluetooth SiP – W2CBW0015 July 26th, 2012 The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorized in writing by Wi2Wi, Inc. Copyright © 2012 Wi2Wi, Inc. Page 3 of 25 List of Figures: Figure 1: Block Diagram ................................................................................................................ 5 Figure 2: SDIO Protocol Timing .................................................................................................. 12 Figure 3: Software Architecture.................................................................................................... 16 Figure 4: Box Diagram ........…

Text truncated - open the document above for the full version.

Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 143 of 145 FCC Part 15C & IC RSS-210 Test Report 20 Exhibit C - EUT Photographs 20.1 EUT- Top View 20.2 EUT- Bottom View Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 144 of 145 FCC Part 15C & IC RSS-210 Test Report 20.3 EUT on Supporting Board - Top View 20.4 Supporting Board - Bottom View EUT Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 145 of 145 FCC Part 15C & IC RSS-210 Test Report 20.5 Antenna View --- END OF REPORT ---

Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 138 of 145 FCC Part 15C & IC RSS-210 Test Report 18 Exhibit A - FCC & IC Equipment Labeling Requirements 18.1 FCC ID Label Requirements As per FCC §2.925, (a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification. Example: FCC ID: XXX123 Where: XXX—Grantee Code, 123—Equipment Product Code As per FCC §15.19, (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labeled as follows: (3) All other devices shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (4) Where a device is constructed in two or more sections connected by wires and marketed together, the statement specified above is required to be affixed only to the main control unit. If the EUT is integrated within another device then a label affixed to the host shall also state, “Contains FCC ID: XXXXXX” (5) When the device is so small or for such use that it is not practicable to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. 18.2 IC Label Requirements As per IC RSS-Gen §5, the certification number shall appear as follows: IC: XXXXXX-YYYYYYYY Where: • "XXXXXX-YYYYYYYY" is the certification number • "XXXXXX" is the Certificate Holder Number (CHN), made of at most 6 alphanumeric characters (A-Z, 0-9), assigned by Industry Canada; and • "YYYYYYYY" is the Unique Product Number (UPN), made of at most 11 alphanumeric characters (A-Z, 0-9) assigned by the applicant. • Note 1: The term "IC" before the equipment certification number only signifies that the Industry Canada technical specifications were met. • Note 2: Note 1 shall be conspicuously placed in the equipment user manual. • Note 3: Permitted alphanumeric characters used in the CHN and UPN are limited to capital letters (A-Z) and digits (0-9). Other characters, such as "#", "/" or "-", shall not be used. Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 139 of 145 FCC Part 15C & IC RSS-210 Test Report As per IC RSS-Gen §5.2 Equipment Labeling: Equipment subject to certification under the applicable RSS, shall be permanently labeled on each item, or as an inseparable combination. The label must contain the following information for full compliance: (a) the certification number, prefixed by the term “IC:”; (b) the manufacturer's name, trade name or brand name; and (c) a model name or number. Equipment for which a certificate has been issued is not considered certified if it is not properly labeled. The information on the Canadian label can be combined with the manufacturer’s other labeling requirements. If the device size is too small to put a label, the label can be included in the user’s manual, upon agreement with Industry Canada. 18.3 FCC ID & IC Label Contents and Location

Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 143 of 145 FCC Part 15C & IC RSS-210 Test Report 20 Exhibit C - EUT Photographs 20.1 EUT- Top View 20.2 EUT- Bottom View Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 144 of 145 FCC Part 15C & IC RSS-210 Test Report 20.3 EUT on Supporting Board - Top View 20.4 Supporting Board - Bottom View EUT Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 145 of 145 FCC Part 15C & IC RSS-210 Test Report 20.5 Antenna View --- END OF REPORT ---

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal Government. * This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “*” (Rev.3) FCC PART 15 SUBPART C IC RSS-210, ISSUE 8, DEC 2010 TEST AND MEASUREMENT REPORT For Wi2Wi, Inc. 2107 North 1 st Street, Suite 540, San Jose, CA 95131, USA Report Type: Original Report Product Type: Wi-Fi and BT Combo Module Prepared By: Lionel Lara Report Number: R1206041-247 Report Date: 2012-09-07 Reviewed By: Victor Zhang RF/EMC Lead Bay Area Compliance Laboratories Corp. 1274 Anvilwood Avenue, Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732 9164 FCC ID: U9R-W2CBW0015 IC: 7089A-W2CBW0015 Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 2 of 145 FCC Part 15C & IC RSS-210 Test Report TABLE OF CONTENTS 1 GENERAL DESCRIPTION......................................................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ................................................................................ 6 1.2 MECHANICAL DESCRIPTION OF EUT ....................................................................................................................... 6 1.3 OBJECTIVE............................................................................................................................................................... 6 1.4 RELATED SUBMITTAL(S)/GRANT(S) ........................................................................................................................ 6 1.5 TEST METHODOLOGY.............................................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY...............................................................................................................................6 1.7 TEST FACILITY........................................................................................................................................................ 7 2 SYSTEM TEST CONFIGURATION .......................................................................................................................... 8 2.1 JUSTIFICATION......................................................................................................................................................... 8 2.2 EUT EXERCISE SOFTWARE...................................................................................................................................... 8 2.3 SPECIAL ACCESSORIES............................................................................................................................................ 8 2.4 EQUIPMENT MODIFICATIONS................................................................................................................................... 8 2.5 LOCAL SUPPORT EQUIPMENT.................................................................................................................................. 8 2.6 POWER SUPPLY AND LINE FILTERS.......................................................................................................................... 8 2.7 INTERFACE PORTS AND CABLING............................................................................................................................ 9 2.8 SUPPORTING PARTS LIST AND DETAILS................................................................................................................... 9 3 SUMMARY OF TEST RESULTS ............................................................................................................................. 10 4 FCC §15.247 (I), §2.1091 & IC RSS-102 - RF EXPOSURE .................................................................................... 11 4.1 APPLICABLE STANDARD........................................................................................................................................ 11 4.2 MPE PREDICTION.................................................................................................................................................. 12 4.3 MPE RESULTS....................................................................................................................................................... 12 5 FCC §15.203 & IC RSS-GEN §7.1.4 – ANTENNA DESCRIPTION ...................................................................... 13 5.1 APPLICABLE STANDARD........................................................................................................................................ 13 5.2 ANTENNA CONNECTOR CONSTRUCTION................................................................................................................ 13 6 FCC §15.207 & IC RSS-GEN §7.2.2 - CONDUCTED EMISSIONS ...................................................................... 14 6.1 APPLICABLE STANDARDS...................................................................................................................................... 14 6.2 TEST SETUP........................................................................................................................................................... 14 6.3 TEST PROCEDURE.................................................................................................................................................. 14 6.4 TEST SETUP BLOCK DIAGRAM...............................................................................................................................15 6.5 CORRECTED AMPLITUDE & MARGIN CALCULATION...............................................…

Text truncated - open the document above for the full version.

Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 140 of 145 FCC Part 15C & IC RSS-210 Test Report 19 Exhibit B - Test Setup Photographs 19.1 Radiated Emission below 1 GHz Front View 19.2 Radiated Emission below 1 GHz Rear View Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 141 of 145 FCC Part 15C & IC RSS-210 Test Report 19.3 Radiated Emission above 1 GHz Front View 19.4 Radiated Emission above 1 GHz Rear View Wi2Wi, Inc. FCC ID: U9R-W2CBW0015, IC: 7089A-W2CBW0015 Report Number: R1206041-247 Page 142 of 145 FCC Part 15C & IC RSS-210 Test Report 19.5 AC Line Conducted Emission Front View 19.6 AC Line Conducted Emission Side View