UB8-APCBTTN2Broadband Digital Transmission System

User manual Revision 1.0 24 January 2013 Copyright © 2012 Deliberant www.deliberant.com Deliberant Page 2 Copyright © 2012 Deliberant This user’s guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Deliberant. Notice Deliberant reserves the right to change specifications without prior notice. While the information in this manual has been compiled with great care, it may not be deemed an assurance of product characteristics. Deliberant shall be liable only to the degree specified in the terms of sale and delivery. The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from Deliberant. FCC Caution Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC warning This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Deliberant Page 3 Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Trademarks Deliberant logo is trademark of Deliberant LLC. All other registered and unregistered trademarks in this document are the sole property of their respective owners. 错误！文档中没有指定样式的文字。 Deliberant Page 4 Contents Copyright ............................................................................................................................................. 2 Notice .................................................................................................................................................. 2 Trademarks ......................................................................................................................................... 3 CONTENTS ........................................................................................................................................... 4 ABOUT THIS GUIDE ............................................................................................................................. 6 Prerequisite Skills and Knowledge ...................................................................................................... 6 Conventions Used in this Document ................................................................................................... 6 Abbreviation List .................................................................................................................................. 6 INITIAL DEVICE SETUP ....................................................................................................................... 7 Initial AP Setup .................................................................................................................................... 8 NETWORK OPERATION MODES ..........................................................…

Text truncated - open the document above for the full version.

Deliberant LLC 138 Mountain Brook Dr Canton, GA 30115 United States 2013-01-17 Attn: Director of Certification Authority to Act as Agent Dear Sir/Madam, We, Deliberant LLC, hereby authorize China Certification & Inspection Services Co., Ltd.1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China, Bruce.Zhang. To act as our agent in the preparation of FCC application for the following project: （Broadband Digital Transmission System；APC Button /APC Button AF） We affirm that submitted documents have properly described the device or system and each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will be affixed to a label submitted for approval with this application. Dated this 2013-01-17 Agency agreement expiration date: 2014-01-17 By: Caleb Knauer Signature Printed Title: Director On behalf of : Deliberant LLC Telephone: 8007429865-206

Deliberant LLC 138 Mountain Brook Dr Canton, GA 30115 United States DATE : 2013-01-17 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: UB8-APCBTTN2 Product Name: Broadband Digital Transmission System Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operational Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 2013-01-17 By: Caleb Knauer Signature Printed Title: Director On behalf of : Deliberant LLC Telephone: 8007429865-206

Deliberant LLC 138 Mountain Brook Dr Canton, GA 30115 United States LMA Declaration Letter We , Deliberant LLC declared that will retain control over the final installation of the device, FCC ID : UB8-APCBTTN2 ,such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must be only approved for use when installed in devices produced by a specific manufacturer. Signature: Name / Title ：Caleb Knauer/ Director Tel: 8007429865-206, Fax: 8668938432 Email: [email protected]

Deliberant LLC 138 Mountain Brook Dr Canton, GA 30115 United States (Date) 01/17/2013 Broadband Digital Transmission System FCC ID : UB8-APCBTTN2 , is seeking FCC Authorization as a Single Modular transmitter / Single Limited Modular Approval (Please check one). The EUT meets the requirements for Single Modular approval / Single Limited Modular Approval (please check one) as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below : Questions are: 1. “The modular transmitter must have its own RF shielding.” Yes / No 2. “The modular transmitter must have buffered modulation/data inputs.” Yes / No 3. “The modular transmitter must have its own power supply regulation.” Yes / No 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(c).” Yes / No 5. “The modular transmitter must be tested in a stand-alone configuration.” Yes / No 6. “The modular transmitter must be labeled with its own FCC ID number.” Yes / No 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacture must provide adequate instruction along with the module to explain any such requirements.” Yes / No 8. “The modular transmitter must comply with any applicable RF exposure requirements.” Yes / No Note: (1) LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured. (2) Host devices which contain separately certified modules do not need to be recertified, provided that they meet the following conditions: (i) The host device, as a stand-alone unit without any separately certified modules, complies with all applicable Radio Standards Specifications. (ii) The host device and all the separately certified modules it contains jointly meet the RF exposure compliance requirements of RSS-102, if applicable. (iii) The host device complies with the certification labeling requirements of each of the modules it contains. Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Signature: Name / Title ：Caleb Knauer/ Director Tel: 8007429865-206, Fax: 8668938432 Email: [email protected]

Deliberant LLC, 138 Mountain Brook Drive, Canton, GA 30115 www.deliberant.com Product Differences Declaration To whom it may concern, We, Deliberant LLC, hereby declare: The product model APC Button AF is identical to the model APC Button with regards to the PCB layout, interior structure, and electrical circuitry, as tested by China Certification & Inspection Services Co., Ltd, with the exception of the following differences: 1) Power supply: The APC Button AF supports 802.3af power supply by using a different internal power supply IC compared to APC Button. APC button supports only passive PoE with reduced maximum voltage up to 24VDC. 2) PCB version marking. 3) Model name APC Button AF and APC Button. Regards, Caleb Knauer Deliberant LLC COO January 25, 2013

Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 95 of 103 8 EUT Constructional Details APC Button Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 96 of 103 Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 97 of 103 APC Button AF Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 98 of 103 Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 99 of 103

Label Sise: 10mm X25mm FCC ID: UB8- APCBTTN2 Canada IC: 6607A- APCBTTN2 Label Location

Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 100 of 103 APC Button Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 101 of 103 Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 102 of 103 APC Button AF Report No: CCIS12120030301 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 103 of 103 ------End of report------

China Certification & Inspection Services Co., Ltd. Report No: CCIS12120030302 Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the CCIS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover Page FCC REPORT Applicant: Deliberant LLC Address of Applicant: 138 Mountain Brook Dr Canton, GA 30115 United States Equipment Under Test (EUT) Product Name: Broadband Digital Transmission System Model No.: APC Button,APC Button AF FCC ID: UB8-APCBTTN2 Applicable standards: FCC CFR Title 47 Part 15 Subpart B: 2011 Date of sample receipt: 14 Dec.,2012 Date of Test: 18 Dec.,2012 to 14 Jan.,2013 Date of report issued: 16 Jan.,2013 Test Result : Pass * * In the configuration tested, the EUT complied with the standards specified above. Report No: CCIS12120030302 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 2 of 26 2 Version Version No. Date Description 00 16 Jan.,2013 Original Prepared by: Date: 16 Jan.,2013 Report Clerk Reviewed by: Date: 16 Jan.,2013 Project Engineer Report No: CCIS12120030302 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 3 of 26 3 Contents Page 1 COVER PAGE ......................................................................................................................................................... 1 2 VERSION .................................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................................. 3 4 TEST SUMMARY .................................................................................................................................................... 4 5 GENERAL INFORMATION ................................................................................................................................... 5 5.1 CLIENT INFORMATION ....................................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF E.U.T. .................................................................................................................. 5 5.3 OPERATING MODES .......................................................................................................................................... 5 5.4 DESCRIPTION OF SUPPORT UNITS ................................................................................................................... 6 5.5 DEVIATION FROM STANDARDS .......................................................................................................................... 6 5.6 ABNORMALITIES FROM STANDARD CONDITIONS .............................................................................................. 6 5.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER .................................................................................. 6 5.8 TEST FACILITY ................................................................................................................................................... 6 5.9 TEST LOCATION ................................................................................................................................................ 6 6 TEST INSTRUMENTS LIST .................................................................................................................................. 7 7 TEST RESULTS AND MEASUREMENT DATA ................................................................................................ 8 7.1 CONDUCTED EMISSIONS ................................................................................................................................... 8 7.2 RADIATED EMISSION ....................................................................................................................................... 13 8 TEST SETUP PHOTO .......................................................................................................................................... 23 9 EUT CONSTRUCTIONAL DETAILS ................................................................................................................. 26 Report No: CCIS12120030302 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 4 of 26 4 Test Summary Test Item Section in CFR 47 Result Conducted Emission Part15.107 Pass Readiated Emissions Part15.109 Pass Pass: Th…

Text truncated - open the document above for the full version.

Report No: CCIS12120030302 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 23 of 26 8 Test Setup Photo APC Button Radiated Emission - Below 1GHz Above 1GHz Report No: CCIS12120030302 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 24 of 26 Conducted Emission Report No: CCIS12120030302 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 25 of 26 APC Button AF Radiated Emission - Below 1GHz Above 1GHz Report No: CCIS12120030302 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121200303RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 26 of 26 Conducted Emission 9 EUT Constructional Details Reference to the test report No. CCIS12120030301 ------End of report------