UK3F182FM Transmitter

Operation instructions 1Insert some cigarette ends of ipod car kit in some cigarette devices of automobile of yoursand adjust the suitable angleso that your convenient operation ipod. 2Draw back both armsput your ipod into and equal to the urgent both armslet your protection firmly of ipod among them. 3Will charge the plug and connect it on the base interface of ipodin this way you can charge while listening to the music. 4Choose the transmission frequency of this equipment according to the local frequency situation of radio stationthe switch is presetting frequency to stir the frequency bandtry one’s best to avoid the frequency of the local strong radio stationthen open wave bandFM of auto radioof youis it search platform or manual to search set let auto radio of you receive frequency that you preset automatically to choosein this way you can listen to ipod stereo music of high-fidelity taken the place of to you through ipod car kit device. Specification Transmit Frequency: 88.1MHz 88.3MHz 88.5MHz 88.7MHz Input power: DC12V Frequency Response: 20Hz-20KHz

Power manager audio input fliter frequency and memory Adjustment PLL FM transmit FM stereo modulate MCU ant Trigger the oscillator 19KHZfrequency Modulation signal

1 Photo 1 Appearance of EUT Photo 2 Appearance of EUT

Label FCC ID: UK3F182 50mm The Label must not be a stick-on paper label. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Proposed Label Location on EUT EUT Bottom View/Proposed FCC ID Label Location FCC ID: UK3F182 Label F182 FCC ID: UK3F182 This device complies with Part 15 o the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 35mm

1 Photo 1 Inside of EUT Photo 2 Inside of EUT 2 Photo 3 Inside of EUT

Description of operation Power support The transmitter is fed by 12v car power supply Antenna: The transmitter utilize dipole antenna. The power of this signal (Power manager) will be send to MCU .Audio signal will be process by audio input ,then it be send to FM stereo modulate. MCU will output pulse to trigger the oscillator and the encoder to genetate a carrier frequency and digital code signal when frequency and momeory adjustment was pressed .Then the serially digital signal of encoder will mixed with the carrier at modulator stage by was of FSK mode (frequency Modulation) from the RF VCO,this process uitilize PLL which compare 19KHZ frequency Modulation signal with signal which is from trigger the oscillator Then this signal will pass through time frequency to change into the frequency that required . this signal then pass through LC frequency select network and will be sent to transmitter antenna for transmitting. Ground: There is no external ground connection. The ground is only that of the printed circuit board.

BW007-IPOD-01-TY.sch-1 - Wed Sep 06 09:22:17 2006

EMC TEST REPORT For FM Transmitter Model Number: F182 IP-QRFM88 FCC ID: UK3F182 Report Number : WT068001794 Test Laboratory : Shenzhen Academy of Metrology and Quality Inspection EMC Laboratory Guangdong EMC Compliance Test Center Site Location : Bldg. of Metrology &Quality Inspection, Longzhu Road, Shenzhen, Guangdong, China Tel : 0086-755-26941637, 26941529, 26941531 Fax : 0086-755-26941545 Email : [email protected] Report No.: WT068001702 Page 2/23 TABLE OF CONTENTS TEST REPORT DECLARATION ........................................................................................................4 1. TEST RESULTS SUMMARY ...................................................................................................5 2. GENERAL INFORMATION ....................................................................................................6 2.1. Report information ............................................................................................................6 2.2. Laboratory Accreditation and Relationship to Customer .................................................6 2.3. Measurement Uncertainty .................................................................................................7 3. PRODUCT DESCRIPTION ......................................................................................................7 3.1. EUT Description ...............................................................................................................7 3.2. Related Submittal(s) / Grant (s) ........................................................................................7 3.3. Block Diagram of EUT Configuration..............................................................................7 3.4. Operating Condition of EUT ............................................................................................7 3.5. Special Accessories...........................................................................................................8 3.6. Equipment Modifications..................................................................................................8 3.7. Support Equipment List ....................................................................................................8 3.8. Test Conditions .................................................................................................................8 4. TEST EQUIPMENT USED .......................................................................................................8 4.1. Test Equipment Used to Measure Conducted Disturbance ..............................................8 4.2. Test Equipment Used to Measure Radiated Disturbance and bandwidth.........................8 5. CONDUCTED DISTURBANCE TEST ....................................................................................9 5.1. Test Standard and Limit ....................................................................................................9 5.2. Test Procedure ..................................................................................................................9 5.3. Test Arrangement..............................................................................................................9 5.4. Test Data .........................................................................................................................10 6. RADIATED DISTURBANCE TEST ......................................................................................11 6.1. Test Standard and Limit ..................................................................................................11 6.2. Test Procedure ................................................................................................................11 6.3. Test Arrangement............................................................................................................11 6.4. Test Data .........................................................................................................................11 7. OCCUPIED BANDWIDTH .....................................................................................................14 7.1. Test Standard and Limit ..................................................................................................14 7.2. Test Procedure ................................................................................................................14 7.3. Test Arrangement............................................................................................................14 7.4. Test Data .........................................................................................................................14 8. BAND EDGE .............................................................................................................................16 8.1. Test Standard and Limit ..................................................................................................16 8.2. Band Edge FCC 15.239(d) Limit ....................................................................................16 8.3. Test Procedure ................................................................................................................16 8.4. Test Arrangement............................................................................................................16 8.5. Test Data .........................................................................................................................16 9. ANTENNA REQUIREMENT .................................................................................................16 10. TURNING RANG .....................................................................................................................17 10.1. Test Standard and Limit ..................................................................................................17 Report No.: WT068001702 Page 3/23 10.2. Band Edge FCC 15.239(d) Limit .....................................................…

Text truncated - open the document above for the full version.

Photo 1: Radiated test photo