UL9ADW4401Wireless ADSL 2/2+ Router

Wired / Wireless ADSL 2/2+ Router ADE-3400v3 / ADE-4400v3 / ADW-4401v4 User's Manual 1 Copyright Copyright© 2007 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution To assure continued compliance (example-use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) this Device must accept any interference received, including interference that may cause undesired operation. 2 Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation. R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. WEEE Regulation To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. Revision User’s Manual for Wired / Wireless ADSL 2/2+ Router Model: ADE-3400v3 / ADE-4400v3 / ADW-4401v4 Rev: 1.0 (Nov. 2007) Part No. EM-ADE3400v3_v1 3 Table of Contents 1. INTRODUCTION ........................................................................................................................................... 6 1.1 Feature ................................................................................................................................ 6 1.2 Package Contents .............................................................................................................. 8 1.3 Physical Details .................................................................................................................. 8 2. INSTALLATION .......................................................................................................................................... 14 2.1 System Requirement........................................................................................................ 14 2.2 Hardware Installation .......................................................................................................14 2.3 Configuring the Network Properties............................................................................... 15 3. WEB CONFIGURATION MANAGEMENT.................................................................................................. …

Text truncated - open the document above for the full version.

Photo 1 Appearance of EUT Photo 2 Appearance of EUT

Label Location

FCC ID Label

Photo 1 Inside of EUT Photo 2 Inside of EUT Photo 3 Inside of EUT

ADW4401A MPE calculation Maximum Power output: 2400MHz: 91.2mW (19.6dBm) Max Antenna gain,: 2.0 dBi One-half power: 16.6 dBm Maximum EIRP from transmit antenna is 16.6 + 1.4 =18.0 dBm EIRP To determine the overall exposure at 20 cm from the EUT. The field strength contribution from each antenna is calculated using the equation E, V/m = (30*EIRP,watts) 0.5 /separation distance Maximum EIRP from transmit antenna is 18.0 dBm EIRP = 0.0456 watt EIRP S, mW/cm 2 = E/3770 , E in V/m Total exposure at 20cm: 0.0015 mW.cm 2 For ADW4401A, the duty cycle is 100% the final exposure at 20cm: 0.0015 mW.cm 2 FCC Limit: 1.0 mW/cm 2

EMC TEST REPORT For Wireless ADSL 2/2+ Router Model Number: ADW-4401A, ADW-4401B FCC ID: UL9ADW4401 Report Number : WT088000360 Test Laboratory : Shenzhen Academy of Metrology and Quality Inspection EMC Laboratory Guangdong EMC Compliance Test Center Site Location : Bldg. of Metrology &Quality Inspection, Longzhu Road, Shenzhen, Guangdong, China Tel : 0086-755-26941637, 26941529, 26941531 Fax : 0086-755-26941545 Email : [email protected] Report No.:WT88000360 Page 2/37 TABLE OF CONTENTS TEST REPORT DECLARATION ........................................................................................................4 1. TEST RESULTS SUMMARY ...................................................................................................5 2. GENERAL INFORMATION ....................................................................................................6 2.1. Report information ............................................................................................................6 2.2. Laboratory Accreditation and Relationship to Customer .................................................6 2.3. Measurement Uncertainty .................................................................................................6 3. PRODUCT DESCRIPTION ......................................................................................................7 3.1. EUT Description ...............................................................................................................7 3.2. Related Submittal(s) / Grant (s) ........................................................................................7 3.3. Block Diagram of EUT Configuration..............................................................................8 3.4. Operating Condition of EUT ............................................................................................8 3.5. Special Accessories...........................................................................................................8 3.6. Equipment Modifications..................................................................................................8 3.7. Support Equipment List ....................................................................................................9 3.8. Test Conditions .................................................................................................................9 4. TEST EQUIPMENT USED .....................................................................................................10 5. CONDUCTED DISTURBANCE TEST ..................................................................................11 5.1. Test Standard and Limit ..................................................................................................11 5.2. Test Procedure ................................................................................................................11 5.3. Test Arrangement............................................................................................................11 5.4. Test Data .........................................................................................................................11 6. RADIATED DISTURBANCE TEST ......................................................................................15 6.1. Test Standard and Limit ..................................................................................................15 6.2. Test Procedure ................................................................................................................15 6.3. Test Arrangement............................................................................................................15 6.4. Test Data .........................................................................................................................16 7. 6DB BANDWIDTH MEASUREMENT..................................................................................19 7.1. LIMITS OF 6dB BANDWIDTH MEASUREMENT.....................................................19 7.2. TEST PROCEDURE ......................................................................................................19 7.3. TEST SETUP ..................................................................................................................19 7.4. EUT OPERATING CONDITIONS ................................................................................19 7.5. Test Data .........................................................................................................................19 8. MAXIMUM PEAK OUTPUT POWER .................................................................................23 8.1. LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT .....................23 8.2. TEST PROCEDURES ....................................................................................................23 8.3. TEST SETUP ..................................................................................................................23 8.4. EUT OPERATING CONDITIONS ................................................................................23 8.5. Test Data .........................................................................................................................23 9. POWER SPECTRAL DENSITY MEASUREMENT............................................................24 9.1. LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT................................24 9.2. TEST PROCEDURE ......................................................................................................24 9.3. 4.5.5 TEST SETUP .........................................................................................................24 9.4. 4.5.6 EUT OPERATING CONDITION .........................................................................24 Report No.:WT88000360 Page 3/37 9.5. Test Data .........................................................................................................................24 10. BAND EDGES MEASUREMENT…

Text truncated - open the document above for the full version.

Photo 1 Conducted Emission Test Photo 2 Radiated Emission Test