UWJP10Printer

Paper Microsoft usb Packing List Installation Guide P10 PrintrerQuick Installation Guide Load Paper Charge printer Bluetooth LED Status Code Power Key Funtion Key Feed Key Light guide Part List LED Error Code Caution&FCC/CE Statement Constantly lit FlashingConstantly litConstantly lit OffFlahsingtogether Bluetooth module availableData transactionVia BluetoothPower onnormal statusChargingCharging finished An error has occurred(see Error Code) Out of paper A transmissionerror occurred Print headoverheated Battery voltageis too low Add paper Check the tansmissionstatus Wait untill theprint headcools down Recharge thebattery FCC Compliance Statement “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:ࠉ Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. WARNING:‡'RQRWGLVDVVHPEOHWKH3ULQWHUEDWWHU\ Only qualified technicians may service the device.‡'RQRWXVH3ULQWHUQHDUZDWHU 1. Use desk and mobile PC USB port connect into micro USB of the printer2. When charging the LED will be red, when the battery is fully charged, the LED will turn off.Note: Don’t provide AC adapter for P10 Insert plug here Device name and PINƔ'HYLFHQDPHDQG3,1ODEHOFDQEHIRXQGXQGHU the paper rollDiscovery Modes (factory set)Ɣ$OZD\V$OZD\VGLVFRYHUDEOHƔVW&RQQHFW'LVFRYHUDEOHXQWLOVWFRQQHFWLRQ is establishedƔ0RGH.H\3UHVV0RGH.H\WRPDNHGLVFRYHUDEOH for 90 secondsUsing with Apple devices Ɣ3UHVV0RGH.H\WZLFHWRGLVFRQQHFWDQGSUHVV twice again to reconnectƔ%OXH/('ZLOOIODVKZKHQFRQQHFWLQJGLVFRQQHFWLQJ from Apple devicesƔ6XSSRUWVL26DQGKLJKHU FCC Compliance StatementIncrease the separation between the equipment and receiver.ࠉ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.ࠉ &RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79 technician for help.RF warning statement:The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. EU Regulatory Conformance (XURSH5 77(&RPSOLDQFH6WDWHPHQW+HUHE\%OXH%DPERR declares that this equipment complies with the essential requirement and other relevant provisionRI'LUHFWLYH(&2)7+((8523($13$5/,$0(17$1'7+(&281&,/RI0DUFK 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of WKHLUFRQIRUPLW\ 5 77(  CE NB Mark: For warranty period,repair and service issues,pleasecontant your distributor: Caution&FCC/CE Statement

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 BLUE BAMBOO (HK) LIMITED ______________________________________________________ 02/20/2014 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, _____ BLUE BAMBOO (HK) LIMITED _____hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Name: Printer Model name: P10 FCC ID: UWJP10 We affirm that between SIEMIC and ____ BLUE BAMBOO (HK) LIMITED ___, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature Client’s name / title Huian Gao/ Electrical Engineer Contact information / address Unit 1001, Lucky Building, No.39Wellington Street

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 BLUE BAMBOO (HK) LIMITED ______________________________________________________ 02/20/2014 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: UWJP10 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature : Client’s name / title : Huian Gao/ Electrical Engineer Contact information / address: Unit 1001, Lucky Building, No.39Wellington Street

Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 66 of 82 www.siemic.com.cn Annex B. EUT AND TEST SETUP PHOTOGRAPHS Annex B.i. Photograph 1: EUT External Photo All Packages – Front View EUT-Front View Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 67 of 82 www.siemic.com.cn EUT -Rear View Top View of EUT Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 68 of 82 www.siemic.com.cn Bottom View of EUT Left View of EUT Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 69 of 82 www.siemic.com.cn Right View of EUT

Ø P10 Terminal Label naming rule: Item Content Naming Rules Length Example 1 P Abbreviation notation of New Product 1 P 2 YYWW Manufacturing Date 4 0705 3 P/N Refer to ST part number in ERP 7 400XXXX 4 A Base terminal HW version 1 A~Z 5 XXXXX S equential Number for each lot 5 00001 P0705400XXXXA00001

Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 70 of 82 www.siemic.com.cn Annex B.ii. Photograph 2: EUT Internal Photo Cover Off - Front View 1 Cover Off - Front View 2 Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 71 of 82 www.siemic.com.cn Battery – Front View Battery – Rear View Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 72 of 82 www.siemic.com.cn PCB 1 - Front View PCB 1 - Rear View Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 73 of 82 www.siemic.com.cn PCB 2 - Front View PCB 2 - Rear View Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 74 of 82 www.siemic.com.cn Antenna - Front View Antenna

BLUE BAMBOO (HK) LIMITED Printer Main Model: P10 Serial Model: N/A February 11, 2014 Report No.: 13021194-FCC-H1 (This report supersedes none) Modifications made to the product : None This Test Report is Issued Under the Authority of: Deon Dai Compliance Engineer Alex Liu Technical Manager This test report may be reproduced in full only. Test result presented in this test report is applicable to the representative sample only. Title: RF Exposure Evaluation Report for Printer Main Model: P10 Serial Model: N/A To: §15.247 (i), §2.1093 Report No.: 13021194-FCC-H1 Issue Date: February 11, 2014 Page: 2 of 9 www.siemic.com.cn Laboratory Introduction ATION SIEMIC, headquartered in the heart of Silicon Valley, with superior facilities in US and Asia, is one of the leading independent testing and certification facilities providing customers with one-stop shop services for Compliance Testing and Global Certifications. In addition to testing and certification, SIEMIC provides initial design reviews and compliance management through out a project. Our extensive experience with China, Asia Pacific, North America, European, and international compliance requirements, assures the fastest, most cost effective way to attain regulatory compliance for the global markets. Accreditations for Conformity Assessment Country/Region Scope USA EMC , RF/Wireless , Telecom Canada EMC, RF/Wireless , Telecom Taiwan EMC, RF, Telecom , Safety Hong Kong RF/Wireless ,Telecom Australia EMC, RF, Telecom , Safety Korea EMI, EMS, RF , Telecom, Safety Japan EMI, RF/Wireless, Telecom Singapore EMC , RF , Telecom Europe EMC, RF, Telecom , Safety Title: RF Exposure Evaluation Report for Printer Main Model: P10 Serial Model: N/A To: §15.247 (i), §2.1093 Report No.: 13021194-FCC-H1 Issue Date: February 11, 2014 Page: 3 of 9 www.siemic.com.cn This page has been left blank intentionally. Title: RF Exposure Evaluation Report for Printer Main Model: P10 Serial Model: N/A To: §15.247 (i), §2.1093 Report No.: 13021194-FCC-H1 Issue Date: February 11, 2014 Page: 4 of 9 www.siemic.com.cn CONTENTS 1 EXECUTIVE SUMMARY & EUT INFORMATION .......................................................................................... 5 2 TECHNICAL DETAILS ......................................................................................................................................... 6 3 MODIFICATION ..................................................................................................................................................... 7 4 TEST SUMMARY .................................................................................................................................................... 8 5 MEASUREMENTS, EXAMINATION AND DERIVED RESULTS .................................................................. 9 Title: RF Exposure Evaluation Report for Printer Main Model: P10 Serial Model: N/A To: §15.247 (i), §2.1093 Report No.: 13021194-FCC-H1 Issue Date: February 11, 2014 Page: 5 of 9 www.siemic.com.cn 1 EXECUTIVE SUMMARY & EUT INFORMATION The purpose of this test programme was to demonstrate compliance of the BLUE BAMBOO (HK) LIMITED, Printer and model: P10 against the current Stipulated Standards. The Printer has demonstrated compliance with the §15.247 (i), §2.1093. EUT Information EUT Description Printer Main Model P10 Serial Model N/A Antenna Gain 1 dBi Input Power DC 5V 500mA (Built-in a 7.4V/1000mAh Li-ion battery) Classification Per Stipulated Test Standard §15.247 (i), §2.1093 Title: RF Exposure Evaluation Report for Printer Main Model: P10 Serial Model: N/A To: §15.247 (i), §2.1093 Report No.: 13021194-FCC-H1 Issue Date: February 11, 2014 Page: 6 of 9 www.siemic.com.cn 2 TECHNICAL DETAILS Purpose Compliance testing of Printer with stipulated standard Applicant / Client BLUE BAMBOO (HK) LIMITED Unit 1001, Lucky Building, No.39Wellington Street Manufacturer Shera Technology (Kunshan) Co., Ltd No.377 Changjiang North Road Kunshan Jiangsu 215300 China Laboratory performing the tests SIEMIC (Nanjing-China) Laboratories NO.2-1,Longcang Dadao, Yuhua Economic Development Zone, Nanjing, China Tel: +86(25)86730128/86730129 Fax: +86(25)86730127 Email: [email protected] Test report reference number 13021194-FCC-H1 Date EUT received January 20, 2014 Standard applied §15.247 (i), §2.1093 Dates of test (from – to) January 28, 2014 No of Units : #1 Equipment Category : Spread Spectrum System/Device Trade Name : Blue Bamboo RF Operating Frequency (ies) Bluetooth: 2402-2480 MHz (TX/RX) Number of Channels Bluetooth: 79 Modulation Bluetooth: GFSK&π/4-DQPSK&8DPSK Port USB Port FCC ID UWJP10 Title: RF Exposure Evaluation Report for Printer Main Model: P10 Serial Model: N/A To: §15.247 (i), §2.1093 Report No.: 13021194-FCC-H1 Issue Date: February 11, 2014 Page: 7 of 9 www.siemic.com.cn 3 MODIFICATION NONE Title: RF Exposure Evaluation Report for Printer Main Model: P10 Serial Model: N/A To: §15.247 (i), §2.1093 Report No.: 13021194-FCC-H1 Issue Date: February 11, 2014 Page: 8 of 9 www.siemic.com.cn 4 TEST SUMMARY The product was tested in accordance with the following specifications. All testing has been performed according to below product classification: Test Results Summary FCC Rules Description of Test Result §15.247 (i), §2.1093 RF Exposure Compliance Title: RF Exposure Evaluation Report for Printer Main Model: P10 Serial Model: N/A To: §15.247 (i), §2.1093 Report No.: 13021194-FCC-H1 Issue Date: February 11, 2014 Page: 9 of 9 www.siemic.com.cn 5 MEASUREMENTS, EXAMINATION AND DERIVED RESULTS 5.1 §15.247 (i) and §2.1093/ – RF Exposure Standard Requirement: According to §15.247 (i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Routine SAR evaluation refers to that specifically required by § 2.1093, using measurements or computer simulation. When routine SAR evaluati…

Text truncated - open the document above for the full version.

BLUE BAMBOO (HK) LIMITED Printer Main Model: P10 Serial Model: N/A January 24, 2014 Report No.: 13021194-FCC-R1 (This report supersedes NONE) Modifications made to the product : None This Test Report is Issued Under the Authority of: Deon Dai Compliance Engineer Alex Liu Technical Manager This test report may be reproduced in full only. Test result presented in this test report is applicable to the representative sample only. Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 2 of 82 www.siemic.com.cn Laboratory Introduction SIEMIC, headquartered in the heart of Silicon Valley, with superior facilities in US and Asia, is one of the leading independent testing and certification facilities providing customers with one-stop shop services for Compliance Testing and Global Certifications. In addition to testing and certification, SIEMIC provides initial design reviews and compliance management through out a project. Our extensive experience with China, Asia Pacific, North America, European, and international compliance requirements, assures the fastest, most cost effective way to attain regulatory compliance for the global markets. Accreditations for Conformity Assessment Country/Region Scope USA EMC , RF/Wireless , Telecom Canada EMC, RF/Wireless , Telecom Taiwan EMC, RF, Telecom , Safety Hong Kong RF/Wireless ,Telecom Australia EMC, RF, Telecom , Safety Korea EMI, EMS, RF , Telecom, Safety Japan EMI, RF/Wireless, Telecom Singapore EMC , RF , Telecom Europe EMC, RF, Telecom , Safety Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 3 of 82 www.siemic.com.cn This page has been left blank intentionally. Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 4 of 82 www.siemic.com.cn CONTENTS 1 EXECUTIVE SUMMARY & EUT INFORMATION .......................................................................................... 5 2 TECHNICAL DETAILS ......................................................................................................................................... 6 3 MODIFICATION ..................................................................................................................................................... 7 4 TEST SUMMARY .................................................................................................................................................... 8 5 MEASUREMENTS, EXAMINATION AND DERIVED RESULTS .................................................................. 9 ANNEX A. TEST INSTRUMENT & METHOD ........................................................................................................ 60 ANNEX B. EUT AND TEST SETUP PHOTOGRAPHS ........................................................................................... 66 ANNEX C. TEST SETUP AND SUPPORTING EQUIPMENT ................................................................................ 77 ANNEX D. USER MANUAL / BLOCK DIAGRAM / SCHEMATICS / PART LIST ............................................ 81 ANNEX E. DECLARATION OF SIMILARITY ........................................................................................................ 82 Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 5 of 82 www.siemic.com.cn 1 EXECUTIVE SUMMARY & EUT INFORMATION The purpose of this test programme was to demonstrate compliance of the BLUE BAMBOO (HK) LIMITED, Printer and model: P10 against the current Stipulated Standards. The Printer has demonstrated compliance with the FCC 15.247: 2013, ANSI C63.4: 2009. EUT Information EUT Description Printer Main Model P10 Serial Model N/A Antenna Gain 1 dBi Input Power DC 5V 500mA (Built-in a 7.4V/1000mAh Li-ion battery) Classification Per Stipulated Test Standard FCC 15.247: 2013, ANSI C63.4: 2009 Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 6 of 82 www.siemic.com.cn 2 TECHNICAL DETAILS Purpose Compliance testing of Printer with stipulated standard Applicant / Client BLUE BAMBOO (HK) LIMITED Unit 1001, Lucky Building, No.39Wellington Street Manufacturer Shera Technology (Kunshan) Co., Ltd No.377 Changjiang North Road Kunshan Jiangsu 215300 China Laboratory performing the tests SIEMIC (Nanjing-China) Laboratories NO.2-1,Longcang Dadao, Yuhua Economic Development Zone, Nanjing, China Tel:+86(25)86730128/86730129 Fax:+86(25)86730127 Email: [email protected] Test report reference number 13021194-FCC-R1 Date EUT received January 20, 2014 Standard applied FCC 15.247: 2013, ANSI C63.4: 2009 Dates of test (from – to) January 28, 2014 No of Units #1 Equipment Category DSS Trade Name N/A RF Operating Frequency (ies) Bluetooth : 2402-2480 MHz Number of Channels Bluetooth: 79CH Modulation Bluetooth: GFSK&π/4-DQPSK &8DPSK Port USB Port FCC ID : UWJP10 Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 7 of 82 www.siemic.com.cn 3 MODIFICATION None Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 8 of 82 www.siemic.com.cn 4 TEST SUMMARY The product was tested in accordance with the following specifications. All testing has been performed according to below product classification: Spread Spectrum System/Device Test Results Summary Test Standard Description Product Class Pass / Fail §15.247(i), §2.1093 RF Exposure See Above Pass §15.203 Antenna Requirement …

Text truncated - open the document above for the full version.

Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 75 of 82 www.siemic.com.cn Annex B.iii. Photograph 3: Test Setup Photo Conducted Emissions Test Setup – Front View Conducted Emissions Test Setup – Side View Title: RF Test Report for Printer Main Model: P10 Main Model: N/A To: FCC 15.247: 2013, ANSI C63.4: 2009 Report No: 13021194-FCC-R1 Issue Date: January 24, 2014 Page: 76 of 82 www.siemic.com.cn Radiated Spurious Emissions Test Setup Below 1GHz - Front View Radiated Spurious Emissions Test Setup Above 1GHz –Front View