UWJP200P200

Battery Packing List PrinterPaper 1A Power Adapter (3A optional) Front Feed Button USB Port Menu Key Power Jack MSR Power Button Paper Cutter Status LED Cancel Key Clear Key Enter Key Serial Port Navigation Key Numeric Keypad Battery Cover Back Contact your distributor for replacement parts Load Paper Front Printer 1. Open the lid. 2. Install paper roll with paper pointing up. 3. Pull out a small amount of paper, close lid. Install Battery 1. Remove the battery cover. 2. Plug in the battery cable into the connector. 3. Install the battery into the slot and install the battery cover. Battery Connector Install SAM Card 1. Remove the battery cover and battery. 2. Open the card holder and insert the SAM card with the electronic chip facing down and the cut-out corner on top. 3. Close the card holder and lock it into place. 4. Install the battery and the battery cover. SAM Slot Power & Charging 1. Insert the DC plug of power adapter* into the power jack of printer. 2. Plug power adaptor into AC power outlet. *Optional 3Amp power supply required when running without battery. Power Jack For warranty period, repair and service issues, please contact your distributor: Europe-R&TTE Compliance Statement Hereby, Blue Bamboo declares that this equipment complies with the essential requirement and other relevant provision of Directive 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of march 9,1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity(R&TTE). CE NB Mark: CE Statement Smart Card Position the smart card and insert it into the smart card reader slot with the chip facing down. MSR 1. Position the card with the magnetic stripe facing down and towards the printer. 2. Swipe it through the reader in either direction. FCC Statement FCC ID: UWJP200 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. PART 15.21 STATEMENT (3) Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (4) For receivers and Class B digital This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna · Increase the separation between the equipment or devices · Connect the equipment to an outlet other than the receiver's · Consult a dealer or an experienced radio/TV technician for assistance Bluetooth The P200 printer can communicate with other Bluetooth SPP compatible devices, such as peripheral equipment PDAs, mobile phones, and computers. Confirm that your host device supports the SPP (Serial Port Profile) before using the P200 printer. Bluetooth communication distance is up to 10m. Default Device Name: P200 Default PIN Code: 1234 Environment Operating Temperature: 0~40°C (+32° to 104°F) Operating Humidity: 20~85%, no condensation Storage Temperature: -20~60°C (-4° to 140°F) Storage Humidity: 10~90%, no condensation WARNING: • Do not disassemble the Printer, battery or AC adapter. Only qualified technicians may service the device. • Do not use batteries, AC adapters or Printer near water. Caution 1588

04/07/09 - 3 Authority to Act as Agent Date: Feb-22-2012 American Telecommunication Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. is authorized to act on our behalf, until otherwise notified, for applications to American Telecommunication Certification Body, Inc. (ATCB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b) , to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: _____8 Months_____ By: Huian Gao (Signature 1 ) (Print name) Title: Compliance Engineer On behalf of: BLUE BAMBOO HK LIMIED (Company Name) Telephone: 8602152190333-322 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Declaration Letter We are declaring that the product function: 1 P200 Printer USB port is not connection to PC device and not charge function. 2 And with RFID function communication via bluetooth transmission data, It is not meantime working. 3 Other for card slot that is SAM card, only data security for software, is not for GM device interface. Sincerely, (signature) Printed Name Huian Gao Compliance Enginner BLUE BAMBOO HK LIMITED

04/07/09 - 3 Request for Confidentiality Date: 2-20-2012 Subject: Confidentiality Request for FCC ID: ___UWJP200________ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 2 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ ______BLUE BAMBOO HK LIMITED __ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___180 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ATCB in the event information regarding the product or the product is made available to the public. ATCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By: Compliance Engineer Huian Gao__ (Signature/Title 3 ) (Print name) 2 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 1 of 6 APPENDIX 1 PHOTOGRAPHS OF EUT SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 2 of 6 EUT Front View Rear View SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 3 of 6 Left View Right View SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 4 of 6 Top View Bottom View SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 5 of 6 EUT Charger and Battery EUT Charger and BatteryEUT Charger and Battery EUT Charger and Battery SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 6 of 6

P200 base terminal Item Content Naming Rules Length Example 1P P=P200 1P 2 YYWW Manufacturing Date 4 0705 3 P/N Refer to ST part number in ERP 7 400XXXX 4 A Base terminal HW version 1 A~Z 5 XXXXX Sequential Number for each lot 5 00001 (xx)xxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxx

SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 1 of 9 APPENDIX 2 PHOTOGRAPHS OF EUT SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 2 of 9 Open EUT SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 3 of 9 Internal of PCB Front View Internal of PCB Rear View SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 4 of 9 RFID 13.56 MHz LOOP Antennas RF Board Front View SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 5 of 9 Bluetooth Antenna RF Board Rear View SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 6 of 9 LCD Front View LCD Rear View SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 7 of 9 Keypad Front View Keypad Rear View SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 8 of 9 Magcard Reader SGS-CSTC Standards Technical Services（ （（ （Shanghai） ）） ） Co., Ltd. Page 9 of 9 Print Head

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. 588 West Jindu Road,Songjiang District,Shanghai,China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5655 [email protected] Report No.: SHEM120100004905 Page: 1 of 6 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only Member of the SGS Group (SGS SA) Statement of compliance to SAR Application No. : SHEM120100004905 Applicant: BLUE BAMBOO HK LIMITED 10/F COSCO TOWER GRAND MILLENNIUM PLAZA 183 QUEEN’S RAOD CENTRAL HK FCC ID: UWJP200 Fundamental Frequency : 13.56MHz 2402-2480 MHz Equipment Under Test (EUT): Marking: BLUE BAMBOO Name: Printer Model No.: P200 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Jim Xu Neil Zhang E&E Section Head E&E Project Engineer SGS-CSTC(Shanghai) Co., Ltd. SGS-CSTC(Shanghai) Co., Ltd. SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM110900119303 Page: 2 of 6 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 1. As we can see from the 13.56MHz maximum fundamental field strength is 73.37dBuv at 3M in the test report SHEM120100004904， ，， ，based on the ANSI 63.10- 2009 section 7.8.2 calculation the peak output power: 7.8.2 Calculation of the peak output power of the EUT 7.8.2 Calculation of the peak output power of the EUT7.8.2 Calculation of the peak output power of the EUT 7.8.2 Calculation of the peak output power of the EUT The peak output power of the EUT may be calculated from the measured peak field strength, if the gain of the EUT radiating element is known, using Equation (5). P is the power, in W E is the measured peak field strength, in V/m d is the distance at which the measurement was made, in m G is the numeric gain of the radiating element If the gain of the radiating element is not known, then either the effective radiated power (ERP) or the effective isotropic radiated power (EIRP) may be calculated from the measured peak field strength, by using either G = 1.64 or G = 1, respectively, in Equation (5). 1.1 E is the measured maximum fundamental field strength in V/m E=73.37dBuV/m=0.0047V/m 1.2 d is the distance in meters from which the field strength was measured. d=3 meter 1.3 G is the numeric gain of the transmitting antenna with reference to an isotropic radiator. G=1 numeric (Loop Antenna gain is 0dBi) 1.4 P is the power in watts for which you are solving: P = (Ed) ²/30G=(0.0047*3)²/30*1=0.000006627W=0.006627mW 2. As we can see from the Bluetooth maximum output power in the report SHEM120100004903: Output Power Test Channel Modulatio n Fundamental Frequency (GHz) Reading Power (dBm) Cable Loss (dB) (dBm) (mW) Limit (dBm) GFSK 0.83 0.6 1.43 1.39 30 π/4- DQPSK -1.14 0.6 -0.54 0.88 30 Lowest 8DPSK 2.402 -0.94 0.6 -0.34 0.92 30 GFSK 0.29 0.6 0.89 1.23 30 π/4- DQPSK -1.73 0.6 -1.13 0.77 30 Middle 8DPSK 2.441 -1.49 0.6 -0.89 0.81 30 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM110900119303 Page: 3 of 6 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road,Songjiang District,Shanghai,China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5655 [email protected] Report No.: SHEM120100004903 Page: 1 of 66 . Jim Xu Neil Zhang E&E Section Head E&E EMC Engineer SGS-CSTC(Shanghai) Co., Ltd. SGS-CSTC(Shanghai) Co., Ltd. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only TEST REPORT Application No. : SHEM120100004903 Applicant: BLUE BAMBOO HK LIMITED FCC ID: UWJP200 Fundamental Carrier Frequency : 2.402GHz to 2.480GHz Equipment Under Test (EUT): Product Name: Printer Brand Name: BLUE BAMBOO Model No.: P200 Standards: FCC PART 15 SUBPART C, Section 15.247 Date of Receipt: Jan. 19, 2012 Date of Test: Jan. 20, 2012 to Feb 28, 2012 Date of Issue: Feb 29, 2012 Test Result : PASS * * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 2 of this report for further detail . SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM120100004903 Page: 2 of 66 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 2 Test Summary Test items Test Requirement Test Procedure Result Antenna Requirement Section 15.247 (c) --- PASS Occupied Bandwidth Section 15.247 (a)(1) ANSI C63.10:2009 DA 00-705 PASS Carrier Frequencies Separated Section 15.247(a)(1) DA 00-705 PASS Hopping Channel Number Section 15.247(a)(1)(iii) DA 00-705 PASS Dwell Time Section 15.247(a)(1)(iii) DA 00-705 PASS Maximum Peak Output Power Section 15.247(b)(1) ANSI C63.10:2009 PASS Conducted Spurious Emission (30MHz to 25GHz) Section 15.207 &15.247(d) ANSI C63.10:2009 PASS Radiated Spurious Emission (30MHz to 25GHz) Section 15.209 &15.247(d) ANSI C63.10:2009 PASS Band Edges Measurement Section 15.247 (d) &15.205 ANSI C63.10:2009 PASS SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM120100004903 Page: 3 of 66 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 3 Contents Page 1 COVER PAGE .............................................................................................................................................1 2 TEST SUMMARY.................................................................................................................................................... 2 3 CONTENTS..................................................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Page 1 of 3 APPENDIX 3 PHOTOGRAPHS OF EUT TEST SETUP SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Page 2 of 3 AC Power line Conducted Emissions Radiated Emission 9 KHz~30MHz SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Page 3 of 3 30MHz-1GHz Above 1GHz