UZZSFQ07Sound Spot

Sound Spot SFQ-07 User Manual 4 CAUTION - Proper Installation y Install the system in a place which is level, dry and neither too hot nor too cold. The appropriate temperature is between 5 oC and 35 oC. y Install the system in a location with adequate ventilation to prevent internal heat from building up inside the unit. y Leave sufficient distance between the system and TV. y Keep the system away from TV to avoid interference with TV. CAUTION - Proper Ventilation To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: Front: No obstructions and open spacing. Sides / Top / Back: No obstructions should be placed in the areas shown by the dimensions below. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm (3-15/16") or more. Front View: Side View: Information for Users on Disposal of Old Equipment [European Union] This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the recycling in accordance with your national legislation. By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health that could otherwise be caused by inappropriate waste handling of this product. For more information about collection point and recycling of this product, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. [Other Countries outside the European Union] If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment. QDID: xxxxxxx Attention: This symbol is only valid in the European Union. 15 cm (5- 15 / 16 ") 15 cm (5- 15 / 16 ") 15 cm (5- 15 / 16 ") 10 cm (3- 15 / 16 ") 15 cm (5- 15 / 16 ") Fr o n t si d eBack si d e 5 Contents Getting Started .............................................................................................. 6 Package Contents ......................................................................................................................... 6 Charging the Built-in Battery ......................................................................................................... 6 Checking Battery Capacity ............................................................................................................ 7 System Overview .......................................................................................... 8 Front View ..................................................................................................................................... 8 Rear View ...................................................................................................................................... 9 Basic Operation .......................................................................................... 10 Turning on/off the System ........................................................................................................... 10 Adjusting the Volume................................................................................................................... 10 Selecting a Sound Mode ............................................................................................................. 10 Activating the Power Saving Mode ............................................................................................. 10 Selecting the Sound Source ...................................................................... 11 Playing back via Bluetooth ........................................................................ 12 Establishing a Bluetooth Connection .......................................................................................... 12 Using Multiple Bluetooth Devices ................................................................................................ 12 Playing back from Macbook or Macbook Pro .............................................................................. 13 Playing back from PC/Notebook ................................................................................................. 13 Playing back from External Source .......................................................... 14 Outputting to other Audio System ............................................................ 15 Dual System Playback ................................................................................ 16 Charging an External Device ..................................................................... 17 Troubleshooting .......................................................................................... 18 Technical Specifications ............................................................................ 19 6 Getting Started Package Contents Examine whether the following package contents are all included: Main Unit USB Power Cable x 1 Aux Cable x 1 Charging the Built-in Battery This system has a built in Lithium Ion battery to give you portable power. To charge the system, connect the micro plug of the USB power cable to the 5V IN jack of the system and the standard plug to USB power output port such as PC USB port. For optimal performance, use only the supplied USB power cable. 5V IN To USB power output port 7 During charging, the charging LED indicator combination with the button will indicate the charging status as follows: System Mode During Charging Charging Complete Standby Blinks in green light at a slow rate. Blinks in white light at a slow rate. Power On but in idle modeBlinks in green light. Blinks in white light. BT mode o…

Text truncated - open the document above for the full version.

S afety Information WARNINGS: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER or OPEN THE CABINET. Dangerous high voltages are present inside the enclosure. No user serviceable parts inside. Leave all servicing to qualied service personnel. PORTABLE CART WARNING (Symbol provided by RETAC) Canada IC statments Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. FCC&IC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS 102. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters from user and bystanders. Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determ ined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.  Consult the dealer or an experienced radio TV technician for help. By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative eects on the environment and human health that could otherwise be caused by inappropriate waste handling of this product. For more information about collection point and recycling of this product, please contact your local municipal oce, your household waste disposal service or the shop where you purchased the product. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. [Other Countries outside the European Union] If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment. CAUTION - Proper Installation  Install the system in a place which is level, dry and neither too hot nor too cold. The appropriate temperature is between 5 o C and 35 o C.  Install the system in a location with adequate ventilation to prevent internal heat from building up inside the unit.  Leave sucient distance between the system and TV.  Keep the system away from TV to avoid interference with TV. CAUTION - Proper Ventilation To avoid risk of electric shock and re, and to prevent damage, locate the apparatus as follows: Front: No obstructions and open spacing. Sides / Top / Back: No obstructions should be placed in the areas shown by the dimensions. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm (3-15/16") or more. Front View:Side View: QDID: B021028 Information for Users on Disposal of Old Equipment [European Union] This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the recycling in accordance with your national legislation. Attention: This symbol is only valid in the European Union. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specied by the manufacturer. 12. Use only with the cart, stand, tripod, bracket or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the l…

Text truncated - open the document above for the full version.

Beautiful Enterprise Co., Ltd. 26 th Floor, Beautiful Group Tower, Tel: 852-23270195 77 Connaught Road Central, Hong Kong Fax: 852-23523380 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. Beautiful Enterprise Co., Ltd would like the following documents regarding this submission for FCC ID: UZZSFQ07 to be kept confidential. 1. Schematic 2. Block diagram 3. Circuit description The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, Name: John Liao Title: Product Approbation Supervisor May 06, 2013

Beautiful Enterprise Co., Ltd. 26 th Floor, Beautiful Group Tower, Tel: 852-23270195 77 Connaught Road Central, Hong Kong Fax: 852-23523380 May 06, 2013 To whom it may concern: We the undersigned, hereby authorize EMCCert DR. RAŠEK GmbH and Neutron Engineering, Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by EMCCert DR. RAŠEK GmbH and Neutron Engineering, Inc. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Beautiful Enterprise Co., Ltd. Sincerely, Signature :............................. Name: John Liao Title: Product Approbation Supervisor

Neutron Engineering Inc. Project No.: 1305C002 Page 2 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 4 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 3 of 14

1 OF 1 2013.05.20 01 (B/E) (Customer) Fo rm NO. :S -ENG-0120-02 CONFIDENTIAL UNDER NDA Rating label 460-032570-000V0 460-032570-000V0 SFQ-07SFQ-07 Art paper ( Printing : BLACK 5 95.5mm 38.7mm 5 - 0.2 AUX INAUX OUTBRIGHT FLATWARM 5V INUSB 5V

Neutron Engineering Inc. Project No.: 1305C002 Page 5 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 6 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 7 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 8 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 9 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 10 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 11 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 12 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 13 of 14 Neutron Engineering Inc. Project No.: 1305C002 Page 14 of 14

Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 1 of 109 FCC/IC Radio Test Report FCC ID: UZZSFQ07 IC: 7633A-SFQ07 This report concerns (check one) : Original Grant Class II Change Issued Date : May. 14, 2013 Project No. : 1305C002 Equipment : Sound Spot Model Name SFQ-07 Applicant : Beautiful Enterprise Co., Ltd. Address : 26th Floor, Beautiful Group Tower, 77 Connaught Road Central, Hong Kong Manufacturer : Beautiful Enterprise Co., Ltd. Address : 26th Floor, Beautiful Group Tower, 77 Connaught Road Central, Hong Kong Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: May. 02, 2013 Date of Test: May. 02, 2013 ~ May. 13, 2013 Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 2 of 109 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of CHINA, or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutron shall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 3 of 109 Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 10 3.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 3.5 DESCRIPTION OF SUPPORT UNITS 12 4 . EMC EMISSION TEST 13 4.1 CONDUCTED EMISSION MEASUREMENT 13 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 4.1.2 MEASUREMENT INSTRUMENTS LIST AND SETTING 13 4.1.3 TEST PROCEDURE 14 4.1.4 DEVIATION FROM TEST STANDARD 14 4.1.5 TEST SETUP 14 4.1.6 EUT OPERATING CONDITIONS 14 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 18 4.2.1 RADIATED EMISSION LIMITS 18 4.2.2 MEASUREMENT INSTRUMENTS LIST ANS SETTING 19 4.2.3 TEST PROCEDURE 20 4.2.4 DEVIATION FROM TEST STANDARD 20 4.2.5 TEST SETUP 21 4.2.6 EUT OPERATING CONDITIONS 22 4.2.7 TEST RESULTS (BELOW 30MHZ) 23 4.2.8 TEST RESULTS (BETWEEN30 – 1000 MHZ) 24 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 37 5 . NUMBER OF HOPPING CHANNEL 61 5.1 APPLIED PROCEDURES / LIMIT 61 5.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 61 5.1.2 TEST PROCEDURE 61 5.1.3 DEVIATION FROM STANDARD 61 5.1.4 TEST SETUP 61 5.1.5 EUT OPERATION CONDITIONS 61 5.1.6 TEST RESULTS 62 6 . AVERAGE TIME OF OCCUPANCY 64 Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 4 of 109 Table of Contents Page 6.1 APPLIED PROCEDURES / LIMIT 64 6.1.1 MEASUREMENT INSTRUMENTS LIST 64 6.1.2 TEST PROCEDURE 64 6.1.3 DEVIATION FROM STANDARD 64 6.1.4 TEST SETUP 65 6.1.5 EUT OPERATION CONDITIONS 65 6.1.6 TEST RESULTS 66 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 78 7.1 APPLIED PROCEDURES / LIMIT 78 7.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 78 7.1.2 TEST PROCEDURE 78 7.1.3 DEVIATION FROM STANDARD 78 7.1.4 TEST SETUP 78 7.1.5 EUT OPERATION CONDITIONS 78 7.1.6 TEST RESULTS 79 8 . BANDWIDTH TEST 83 8.1 APPLIED PROCEDURES / LIMIT 83 8.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 83 8.1.2 TEST PROCEDURE 83 8.1.3 DEVIATION FROM STANDARD 83 8.1.4 TEST SETUP 83 8.1.5 EUT OPERATION CONDITIONS 83 8.1.6 TEST RESULTS 84 9 . PEAK OUTPUT POWER TEST 88 9.1 APPLIED PROCEDURES / LIMIT 88 9.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 88 9.1.2 TEST PROCEDURE 88 9.1.3 DEVIATION FROM STANDARD 88 9.1.4 TEST SETUP 88 9.1.5 EUT OPERATION CONDITIONS 88 9.1.6 TEST RESULTS 89 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 93 10.1 APPLIED PROCEDURES / LIMIT 93 10.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 93 10.1.2 TEST PROCEDURE 93 10.1.3 DEVIATION FROM STANDARD 93 10.1.4 TEST SETUP 93 10.1.5 EUT OPERATION CONDITIONS 93 10.1.6 TEST RESULTS 94 11 . EUT TEST PHOTO 106 Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 5 of 109 1. CERTIFICATION Equipment : Sound Spot Brand Name : Model Name SFQ-07 Applicant : Beautiful Enterprise Co., Ltd. Factory : Shenzhen Synchron Electronics Co., Ltd. Address : No. 9 Mei Li Road, Xia Mei Lin, Fu Tian Area, Shenzhen, Guangdong, China Date of Test : May. 02, 2013 ~ May. 13, 2013 Test Item : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.247) / ANSI C63.4 : 2009 FCC Public Notice DA 00-705, March 30, 2000. Canada RSS-210:2010 RSS-GEN Issue 3, Dec 2010 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FICP-1-1305C002) were obtained utilizing …

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 106 of 109 11. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 107 of 109 Radiated Measurement Photos 9K~30MHz Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 108 of 109 Radiated Measurement Photos 30M~1000MHz Neutron Engineering Inc. Report No.: NEI-FICP-1-1305C002 Page 109 of 109 Radiated Measurement Photos Above 1000MHz