V8YFIU816202T00W150Mbps Wireless-N Mini 3G Broadband Router

Barricade TM N 150Mbps Wireless-N Mini Broadband Router SMCWBR11S-N USER GUIDE 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 Barricade TM SMCWBR11S-N User Guide February 2010 Pub. # 149100000057W E022010-CS-R01 Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2010 by SMC Networks, Inc. 20 Mason Irvine, CA 92618 All rights reserved Trademarks: SMC is a registered trademark; and Barricade, EZ Switch, TigerStack, TigerSwitch, and TigerAccess are trademarks of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders. – 4 – WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http:// www.smc.com. – 5 – COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ◆Reorient or relocate the receiving antenna ◆Increase the separation between the equipment and receiver ◆Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ◆Consult the dealer or an experienced radio/TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC R ADIATION EXPOSURE STATEMENT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. COMPLIANCES – 6 – IC STATEMENT This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2 .35 dBi. Antennas having a higher gain are strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE: IC R ADIATION EXPOSURE STATEMENT: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. AUSTRALIA/NEW ZEALAND AS/NZS 4268 TAIWAN NCC 根據國家通信傳播委員會低功率電波輻射性電機管理辦法規定： 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通 信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 EC CONFORMANCE DECLARATION Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: ◆EN 60950-1: 2006 (IEC 60950-1) — Product Safety ◆EN 55022:2006 + A1:2007, Class B — ITE EMC ◆EN 55024:1998 + A1:2001 + A2:2003 — ITE EMC ACN 066 352010 COMPLIANCES – 7 – ◆EN 300 328 V1.7.1 (2006-10) — Technical requirements for 2.4 GHz radio equipment ◆EN 301 489-1 V1.8.1 (2008-04) — EMC requirements for radio equipment ◆EN 301 489-17 V1.3.2 (2008-04) — EMC requirements for radio equipment ◆50385 (2002) — Country-specific SAR requirements This device is intended for use in the following European Community and EFTA countries: NOTE: The user must use the configuration utility provided with this product to ensure the channels of operation are in conformance with the spectrum usage rules for European Community countries as described below. ◆This device will automatically limit the allowable channels determined by the current country of operation. Incorrectly entering the country of operation may result in illegal operation and may cause harmful interference to other systems. The user is obligated to ensure the device is operating according to the channel limitations, indoor/outdoor restrictions and license requirements for each European Community country as described in this document. DECLARATION OF CONFORMITY IN LANGUAGES OF THE EUROPEAN C OMMUNITY ◆Austria◆Belgium◆Bulgaria◆Cyprus◆Czech Republic ◆Den…

Text truncated - open the document above for the full version.

USER GUIDE 150Mbps Wireless-N Mini Broadband Router WR6202 USER GUIDE WR6202 150Mbps Wireless-N Mini Broadband Router, with one RJ-45 WAN Port, One RJ-45 LAN Port, and IEEE 802.11n Wi-Fi WR6202 E022010-CS-R01 XXXXXXXXXXXXX – 3 – COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ◆Reorient or relocate the receiving antenna ◆Increase the separation between the equipment and receiver ◆Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ◆Consult the dealer or an experienced radio/TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC R ADIATION EXPOSURE STATEMENT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. COMPLIANCES – 4 – IC STATEMENT This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2 .35 dBi. Antennas having a higher gain are strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE: IC R ADIATION EXPOSURE STATEMENT: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. AUSTRALIA/NEW ZEALAND AS/NZS 4268 TAIWAN NCC 根據國家通信傳播委員會低功率電波輻射性電機管理辦法規定： 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通 信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 EC CONFORMANCE DECLARATION Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: ◆EN 60950-1: 2006 (IEC 60950-1) — Product Safety ◆EN 55022:2006 + A1:2007, Class B — ITE EMC ◆EN 55024:1998 + A1:2001 + A2:2003 — ITE EMC ACN 066 352010 COMPLIANCES – 5 – ◆EN 300 328 V1.7.1 (2006-10) — Technical requirements for 2.4 GHz radio equipment ◆EN 301 489-1 V1.8.1 (2008-04) — EMC requirements for radio equipment ◆EN 301 489-17 V1.3.2 (2008-04) — EMC requirements for radio equipment ◆50385 (2002) — Country-specific SAR requirements This device is intended for use in the following European Community and EFTA countries: NOTE: The user must use the configuration utility provided with this product to ensure the channels of operation are in conformance with the spectrum usage rules for European Community countries as described below. ◆This device will automatically limit the allowable channels determined by the current country of operation. Incorrectly entering the country of operation may result in illegal operation and may cause harmful interference to other systems. The user is obligated to ensure the device is operating according to the channel limitations, indoor/outdoor restrictions and license requirements for each European Community country as described in this document. DECLARATION OF CONFORMITY IN LANGUAGES OF THE EUROPEAN C OMMUNITY ◆Austria◆Belgium◆Bulgaria◆Cyprus◆Czech Republic ◆Denmark◆Estonia◆Finland◆France◆Germany ◆Greece◆Hungary◆Iceland◆Ireland◆Italy ◆Latvia◆Lithuania◆Luxembourg◆Malta◆Netherlands ◆Norway◆Poland◆Portugal◆Romania◆Slovakia ◆Slovenia◆Spain◆Sweden◆Switzerland◆United Kingdom Czech Česky Manufacturer tímto prohlašuje, že tento Radio LAN device je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Estonian Eesti Käesolevaga kinnitab Manufacturer seadme Radio LAN device vastavust direktiivi 1999/ 5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. EnglishHereby, Manufacturer, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Suomi Valmistaja Manufacturer vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Dutch …

Text truncated - open the document above for the full version.

USER GUIDE Pareto Networks BG-100 Branch Services Gateway BG-100 USER GUIDE BG-100 Pareto Networks BG-100 Branch Services Gateway with one RJ-45 WAN Port, One RJ-45 LAN Port, and IEEE 802.11n Wi-Fi BG-100 E022010-CS-R01 *************** – 3 – COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ◆Reorient or relocate the receiving antenna ◆Increase the separation between the equipment and receiver ◆Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ◆Consult the dealer or an experienced radio/TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC R ADIATION EXPOSURE STATEMENT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. COMPLIANCES – 4 – The following three 3G cards have passed the co-located EMC/RF exposure test with this device and can be used with this device. Other 3G cards may or may not comply with FCC rules, please consult the manufacturer before purchase. IC STATEMENT This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2 .35 dBi. Antennas having a higher gain are strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE: IC R ADIATION EXPOSURE STATEMENT: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. AUSTRALIA/NEW ZEALAND AS/NZS 4268 InterfaceBrandProduct Name ModelFCC IDNCC ID USB Port HUAWEI T HS DPA USB Stick E169QISE169CCAD083G0060T5 ZTEHSDPA USB Modem MF626Q78-ZTEMF622 N/A HuaweiHSDPA USB Modem E220QISE220N/A ACN 066 352010 COMPLIANCES – 5 – TAIWAN NCC 根據國家通信傳播委員會低功率電波輻射性電機管理辦法規定： 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通 信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 EC CONFORMANCE DECLARATION Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: ◆EN 60950-1: 2006 (IEC 60950-1) — Product Safety ◆EN 55022:2006 + A1:2007, Class B — ITE EMC ◆EN 55024:1998 + A1:2001 + A2:2003 — ITE EMC ◆EN 300 328 V1.7.1 (2006-10) — Technical requirements for 2.4 GHz radio equipment ◆EN 301 489-1 V1.8.1 (2008-04) — EMC requirements for radio equipment ◆EN 301 489-17 V1.3.2 (2008-04) — EMC requirements for radio equipment ◆50385 (2002) — Country-specific SAR requirements This device is intended for use in the following European Community and EFTA countries: NOTE: The user must use the configuration utility provided with this product to ensure the channels of operation are in conformance with the spectrum usage rules for European Community countries as described below. ◆This device will automatically limit the allowable channels determined by the current country of operation. Incorrectly entering the country of operation may result in illegal operation and may cause harmful interference to other systems. The user is obligated to ensure the device is operating according to the channel limitations, indoor/outdoor ◆ Austria◆Belgium◆Bulgaria◆Cyprus◆Czech Republic ◆Denmark◆Estonia◆Finland◆France◆Germany ◆Greece◆Hungary◆Iceland◆Ireland◆Italy ◆Latvia◆Lithuania◆Luxembourg◆Malta◆Netherlands ◆Norway◆Poland◆Portugal◆Romania◆Slovakia ◆Slovenia◆Spain◆Sweden◆Switzerland◆United Kingdom COMPLIANCES – 6 – restrictions and license requirements for each European Community country as described in this document. DECLARATION OF CONFORMITY IN LANGUAGES OF THE EUROPEAN COMMUNITY Czech Česky Manufacturer tímto prohlašuje, že tento Radio LAN device je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Estonian Eesti Käesolevaga kinnitab Manufacturer seadme Radio LAN device vastavust direktiivi 1999/ 5/EÜ põhinõuete…

Text truncated - open the document above for the full version.

Barricade TM N 150Mbps Wireless-N Mini 3G Broadband Router SMCWBR11S-3GN USER GUIDE 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 Barricade TM SMCWBR11S-3GN User Guide February 2010 Pub. # 149100000057W E022010-CS-R01 Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2010 by SMC Networks, Inc. 20 Mason Irvine, CA 92618 All rights reserved Trademarks: SMC is a registered trademark; and Barricade, EZ Switch, TigerStack, TigerSwitch, and TigerAccess are trademarks of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders. – 4 – WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http:// www.smc.com. – 5 – COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ◆Reorient or relocate the receiving antenna ◆Increase the separation between the equipment and receiver ◆Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ◆Consult the dealer or an experienced radio/TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC R ADIATION EXPOSURE STATEMENT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. COMPLIANCES – 6 – The following three 3G cards have passed the co-located EMC/RF exposure test with this device and can be used with this device. Other 3G cards may or may not comply with FCC rules, please consult the manufacturer before purchase. IC STATEMENT This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2 .35 dBi. Antennas having a higher gain are strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE: IC R ADIATION EXPOSURE STATEMENT: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. AUSTRALIA/NEW ZEALAND AS/NZS 4268 InterfaceBrandProduct Name ModelFCC IDNCC ID USB Port HUAWEI T HSDPA USB Stick E169QISE169CCAD083G0060T5 ZTEHSDPA USB Modem MF626Q78-ZTEMF622 N/A HuaweiHSDPA USB Modem E220QISE220N/A ACN 066 352010 COMPLIANCES – 7 – TAIWAN NCC 根據國家通信傳播委員會低功率電波輻射性電機管理辦法規定： 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通 信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 EC CONFORMANCE DECLARATION Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: ◆EN 60950-1: 2006 (IEC 60950-1) — Product Safety ◆EN 55022:2006 + A1:2007, Class B — ITE EMC ◆EN 55024:1998 + A1:2001 + A2:2003 — ITE EMC ◆EN 300 328 V1.7.1 (2006-10) — Technical requirements for 2.4 GHz radio equipment ◆EN 301 489-1 V1.8.1 (2008-04) — EMC requirements for radio equipment ◆EN 301 489-17 V1.3.2 (2008-04) — EMC requirements for radio equipment ◆50385 (2002) — Country-specific SAR requirements This device is intended for use in the following European Community and EFTA countries: NOTE: The user must use the configuration utility provided with this product to ensure the channels of operation are in conformance with the spectrum usage rules for European Community countries as described below. ◆This device will automatically limit the allowable channels determined by the current country of operation. Incorrectly entering the country of operati…

Text truncated - open the document above for the full version.

USER GUIDE 150Mbps Wireless-N Mini 3G Broadband Router WR6202-1U USER GUIDE WR6202-1U 150Mbps Wireless-N Mini 3G Broadband Router, with one RJ-45 WAN Port, One RJ-45 LAN Port, and IEEE 802.11n Wi-Fi WR6202-1U E022010-CS-R01 XXXXXXXXXXXXX – 5 – COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ◆Reorient or relocate the receiving antenna ◆Increase the separation between the equipment and receiver ◆Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ◆Consult the dealer or an experienced radio/TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC R ADIATION EXPOSURE STATEMENT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. COMPLIANCES – 6 – The following three 3G cards have passed the co-located EMC/RF exposure test with this device and can be used with this device. Other 3G cards may or may not comply with FCC rules, please consult the manufacturer before purchase. IC STATEMENT This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2 .35 dBi. Antennas having a higher gain are strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE: IC R ADIATION EXPOSURE STATEMENT: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. AUSTRALIA/NEW ZEALAND AS/NZS 4268 InterfaceBrandProduct Name ModelFCC IDNCC ID USB Port HUAWEI T HSDPA USB Stick E169QISE169CCAD083G0060T5 ZTEHSDPA USB Modem MF626Q78-ZTEMF622 N/A HuaweiHSDPA USB Modem E220QISE220N/A ACN 066 352010 COMPLIANCES – 7 – TAIWAN NCC 根據國家通信傳播委員會低功率電波輻射性電機管理辦法規定： 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通 信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 EC CONFORMANCE DECLARATION Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: ◆EN 60950-1: 2006 (IEC 60950-1) — Product Safety ◆EN 55022:2006 + A1:2007, Class B — ITE EMC ◆EN 55024:1998 + A1:2001 + A2:2003 — ITE EMC ◆EN 300 328 V1.7.1 (2006-10) — Technical requirements for 2.4 GHz radio equipment ◆EN 301 489-1 V1.8.1 (2008-04) — EMC requirements for radio equipment ◆EN 301 489-17 V1.3.2 (2008-04) — EMC requirements for radio equipment ◆50385 (2002) — Country-specific SAR requirements This device is intended for use in the following European Community and EFTA countries: NOTE: The user must use the configuration utility provided with this product to ensure the channels of operation are in conformance with the spectrum usage rules for European Community countries as described below. ◆This device will automatically limit the allowable channels determined by the current country of operation. Incorrectly entering the country of operation may result in illegal operation and may cause harmful interference to other systems. The user is obligated to ensure the device is operating according to the channel limitations, indoor/outdoor ◆ Austria◆Belgium◆Bulgaria◆Cyprus◆Czech Republic ◆Denmark◆Estonia◆Finland◆France◆Germany ◆Greece◆Hungary◆Iceland◆Ireland◆Italy ◆Latvia◆Lithuania◆Luxembourg◆Malta◆Netherlands ◆Norway◆Poland◆Portugal◆Romania◆Slovakia ◆Slovenia◆Spain◆Sweden◆Switzerland◆United Kingdom COMPLIANCES – 8 – restrictions and license requirements for each European Community country as described in this document. DECLARATION OF CONFORMITY IN LANGUAGES OF THE EUROPEAN COMMUNITY Czech Česky Manufacturer tímto prohlašuje, že tento Radio LAN device je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Estonian Eesti Käesolevaga kinnitab Manufacturer seadme Radio LAN device vastavust direktiivi 1999/ 5/EÜ põhinõuet…

Text truncated - open the document above for the full version.