VDE-GGCACGenerator connectivity accessory

Install guide Items FCC ID number VDE-GGCAC and IC ID number 8036A-GGCAC This device contains Wi-Fi/BLE module: FCC ID: 2AC7Z-ESPS3WROOM1 ICID: 21098-ESPS3WROOM1 Note: At least 20 cm separation distance between the antenna and the user’s body must be maintained at all times Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oƯ and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit diƯerent from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Note: changes or modifications not expressly approved by Generac may void the user's authority to operate the equipment. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

To whom it may concern: This is a new certification application of a device that contains cellular module Sierra HL7810, which is currently approved under FCC ID N7NHL78A and IC: 2417C-HL78A. Although originally cerƟfied with an eSIM on board, Sierra offers a version of this module that contains no eSIM. Sierra has done the necessary due diligence to determine that the version with no eSIM falls under the classificaƟon of a class 1 permissive change that has no effect on the RF behavior of the device. The version with no eSIM is the one that we are using. No modificaƟons are being made to the module that we are purchasing from Sierra and all guidance specified in the modular approval grant is met except for the 2dBi maximum antenna gain. Given that the antenna (Taoglas PCS.66.A) falls outside of the maximum 2dBi gain specified in the grant, we are requesƟng this new cerƟficaƟon in accordance with KDB 996369 D02 Module Q and A v02. Included in this filing are the following items as specified in KDB 996369 D02 Module Q and A v002: - Relevant test reports from the original module filing. These test reports accurately represent test results under the new condiƟons: o Part 22 test report for module FCC ID N7NHL78 o Part 24 test report for module FCC ID N7NHL78 o Part 27 test report for module FCC ID N7NHL78 (split into two documents due to size) - Spurious emissions measurements of the HL7810 using the Taoglas PCS.66.A - Updated MPE evaluaƟon All reported fundamental power levels in this filing were calculated using the reported power levels from the module’s grant and the gain of the Taoglas PCS.66A antenna at the associated frequencies. Regards, JeƯrey Jonas Senior StaƯ Engineer-Global Product Compliance

April 2, 2024 ACB, Inc. 313 Park Avenue Suite 300 Falls Church, Virginia 22046 Subject: Authority to Use FCC/ISED Exhibits for Equipment Certification Applications We, Sierra Wireless, ULC, hereby authorise Generac Power Systems Inc. to use, where applicable, our test reports filed with the Federal Communications Commission (FCC) under FCC ID: N7NHL78A and Innovation, Science and Economic Development Canada (ISED) under IC: 2417C-HL78A for the sole purpose of supporting Generac Power Systems Inc.’s equipment certification applications reference FCC ID: VDE- GGCAC and IC: 8036A - GGCAC. As our FCC/ISED filings for FCC ID: N7NHL78A and IC: 2417C-HL78A leveraged the test reports filed under FCC ID: N7NHL78 and IC: 2417C-HL78 respectively, we further authorise Generac Power Systems Inc. to use, where applicable, our test reports filed with the FCC under FCC ID: N7NHL78 and the ISED under IC: 2417C-HL78 for the same purpose stated above. Yours sincerely, Ying Wang Director, Regulatory Compliance

External Photos

8 3 7 1 4 6 2 5 9 8 86.0 21.1 15° 54.7 166.0 REVISIONS REVDESCRIPTIONAPPROVEDDATE 1INITIAL RELEASESC2023-10-02 ARELEASE TO PRODUCTIONSC2023-10-05 ITEM NO.PARTNODESCRIPTIONQTY. 1A0004753477HOUSING, G3 CELLULAR RADIO1 2A0004753476COVER, G3 CELLULAR RADIO1 3A0004753478 DISK, MOUNTING, G3 CELLULAR RADIO 1 4A0004753479GASKET, G3 CELLULAR RADIO1 5A0004753482 SCREW, THREAD FORMING, M3 X 6, T10 2 6A0004080870PCBA, 12V CELLULAR, HL78101 7A0004175713DECAL, 12V RADIO1 8A0004753481 SCREW, THREAD FORMING, M3 X 10, T10 9 9A0005166074M12-5F CONN, 60mm LEADS1 TITLE: DATE G3 12V RADIO ASSEMBLY 2023-09-29 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ECOBEE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION ECOBEE INC IS PROHIBITED. S.CAELERS DO NOT SCALE DRAWING NAME 3RD ANGLE PROJECTION MATERIAL FINISH CHECKED DRAWN DIMENSIONS ARE IN MILLIMETRES GENERAL TOLERANCES: X 0.25 X.X 0.10 X.XX 0.05 ANGLES (MACH) 1 ANGLES (BEND) 3 AA0004175705 SHEET 1 OF 1 SCALE: 1:2 REV: PART NO. B SIZE: PROPRIETARY AND CONFIDENTIAL DRAWING PER: ASME Y14.5M-2009 AA BB CC DD EE 6 6 5 5 4 4 3 3 2 2 1 1 SOF-734-02

B1C2D3F4G MODEL: RADIO-G3-12V | INPUT: 12V⎓ 800 mA COO: MALAYSIA IP65 RATED 4006399 Certi � ed to CSA STDs C22.2#62368-1 & 60950-22 Conforms to UL STDs 62368-1 & 60950-22 Contains Transmitter: FCC: 2AC7Z-ESPS3WROOM1 IC: 21098-ESPS3WROOM1 FCC ID: VDE-GGCAC ICID: 8036A-GGCAC CAN ICES-003(B) / NMB-003(B)

Internal Photos

MPE Evaluation The following MPE calculations were re-performed for the Sierra HL8710 (FCC ID N7NHL78A / IC: 2417C-HL78A) using the Taoglas PCS.66.A. Power Density (S) is calculated by the following formula: S=(P*G) /4πR 2 where: S = power density (in appropriate units, e.g. mW/ cm 2 ) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator π = 3.1416 R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) FCC Limits (for general population / uncontrolled exposure): ISED Limits (for general population / uncontrolled exposure): Results: LTE (HL7810 module with Taoglas PCS.66.A antenna): LTE Band Freq. min. (MHz) Freq. max. (MHz) Max Conducted Power (dBm) Radio Power (mW) Antenna Gain (dBi) Power Density @ 20cm (mW/cm^2) Limit (mW/cm^2) PASS/FAIL 2 1850 1910 24.5 281.84 3.2 0.117 1.000 PASS 4 1710 1755 24.5 281.84 3.2 0.117 1.000 PASS 5 824 849 24.5 281.84 1.3 0.076 0.549 PASS 12 699 716 24.5 281.84 1.3 0.076 0.466 PASS 13 777 787 24.5 281.84 1.3 0.076 0.518 PASS 25 1850 1915 24.5 281.84 3.2 0.117 1.000 PASS 66 1710 1780 24.5 281.84 3.2 0.117 1.000 PASS ESP32 (from module MPE report, FCC ID: 2AC7Z-ESPS3WROOM1, IC: 21098-ESPS3WROOM1) Band Freq. min. (MHz) Freq. max. (MHz) Max conducted Power (dBm) Radio Power (mW) Antenna Gain (dBi) Max ERP (mw Power Density @ 20cm (mW/cm^2) Limit (mW/cm^2) PASS/FAIL WiFi 2400 2500 20.5 112.20 3.26 3.26 .047 1.000 PASS BLE 2400 2500 10 10 3.26 3.26 .004 1.000 PASS Colocation: Per technical description, WiFi and LTE will never co-exist in this product. Adding BLE power spectral density of 0.004 mW/cm 2 to all LTE bands still results in a passing result. LTE Band Power Density @ 20cm (mW/cm 2 ) Collocated Power Density @ 20cm (mW/cm 2 ) 2.4GHz Limit (mW/cm 2 ) PASS/FAIL 2 0.117 0.121 1.000 PASS 4 0.117 0.121 1.000 PASS 5 0.076 0.080 1.000 PASS 12 0.076 0.080 1.000 PASS 13 0.076 0.080 1.000 PASS 25 0.117 0.121 1.000 PASS 66 0.117 0.121 1.000 PASS

Engineering Test Report No. 2302602-01 Rev. E Report Date February 29, 2024 Manufacturer Name Generac Power Systems, Inc. Manufacturer Address S45 W29290 Hwy 59 Waukesha, WI 53189 Test Item Name Model No. Generac Generator Connectivity Accessory, Cellular RADIO-G3-12V Date Received January 16, 2024 Test Dates January 16, 2024 through February 9, 2024 Specifications FCC “Code of Federal Regulations” Title 47, Part 15, Subpart C FCC “Code of Federal Regulations” Title 47, Part 22, Subpart C FCC “Code of Federal Regulations” Title 47, Part 24, Subpart C FCC “Code of Federal Regulations” Title 47, Part 27, Subpart L FCC “Code of Federal Regulations” Title 47, Part 90, Subpart S Innovation, Science, and Economic Development Canada, RSS-GEN Innovation, Science, and Economic Development Canada, RSS-130 Innovation, Science, and Economic Development Canada, RSS-132 Innovation, Science, and Economic Development Canada, RSS-133 Innovation, Science, and Economic Development Canada, RSS-139 Test Facility Elite Electronic Engineering, Inc. 1516 Centre Circle, Downers Grove, IL 60515 FCC Reg. Number: 269750 IC Reg. Number: 2987A CAB Identifier: US0107 Signature Tested by Mark E. Longinotti Signature Approved by Raymond J. Klouda, Re gistered Professional Engineer of Illinois – 44894 PO Number 6000209463 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Elite Electronic Engineering Incorporated certifies that the information contained in this report was obtained under conditions which meet or exceed those specified in the FCC and ISED test specifications. The data presented in this test report pertains to the EUT on the test dates specified. Any electrical or mechanical modifications made to the EUT subsequent to the specified test date will serve to invalidate the data and void this certification. This report must not be used to claim product certification, approval, or endorsement by A2LA, NIST, or any agency of the Federal Government. Engineering Test Report No. 2302602-01 Rev. E This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Page 2 of 39 Table of Contents 1. Report Revision History ............................................................................................................................ 3 2. Introduction ............................................................................................................................................... 4 2.1. Scope of Tests .......................................................................................................................................... 4 2.1. Purpose ..................................................................................................................................................... 4 2.2. Identification of the EUT ............................................................................................................................ 4 3. Power Input ............................................................................................................................................... 4 4. Grounding ................................................................................................................................................. 5 5. Support Equipment ................................................................................................................................... 5 6. Interconnect Leads .................................................................................................................................... 5 7. Modifications Made to the EUT ................................................................................................................. 5 8. Modes of Operation ................................................................................................................................... 5 9. Test Specifications .................................................................................................................................... 5 10. Test Plan ................................................................................................................................................... 6 11. Deviation, Additions to, or Exclusions from Test Specifications ............................................................... 6 12. Laboratory Conditions ............................................................................................................................... 6 13. Summary ................................................................................................................................................... 6 14. Sample Calculations ................................................................................................................................. 7 15. …

Text truncated - open the document above for the full version.

Report No.: RF181126C15B Page No. 1 / 150 Report Format Version: 6.1.1 Reference No.: 200611C05 FCC Test Report (PART 22) Report No.: RF181126C15B FCC ID: N7NHL78 Test Model: HL7800 Received Date: Jun. 02, 2020 Test Date: Jun. 02 ~ Jun. 12, 2020 Issued Date: Jul. 09, 2020 Applicant: Sierra Wireless Inc. Address: 13811 Wireless Way, Richmond, BC, Canada V6V3A4 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim any endorsement by TAF. Report No.: RF181126C15B Page No. 2 / 150 Report Format Version: 6.1.1 Reference No.: 200611C05 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Test Site and Instruments ..................................................................................................................... 7 3 General Information ................................................................................................................................... 8 3.1 General Description of EUT .................................................................................................................. 8 3.2 Configuration of System under Test .................................................................................................... 10 3.2.1 Description of Support Units ..................................................................................................... 10 3.3 Test Mode Applicability and Tested Channel Detail ............................................................................. 11 3.4 EUT Operating Conditions .................................................................................................................. 16 3.5 General Description of Applied Standards .......................................................................................... 16 4 Test Types and Results ............................................................................................................................ 17 4.1 Output Power Measurement ............................................................................................................... 17 4.1.1 Limits of Output Power Measurement ...................................................................................... 17 4.1.2 Test Procedures ........................................................................................................................ 17 4.1.3 Test Setup ................................................................................................................................. 18 4.1.4 Test Results .............................................................................................................................. 19 4.2 Modulation Characteristics Measurement .......................................................................................... 42 4.2.1 Limits of Modulation Characteristics ......................................................................................... 42 4.2.2 Test Setup ................................................................................................................................. 42 4.2.3 Test Procedure ......................................................................................................................... 42 4.2.4 Test Results .............................................................................................................................. 43 4.3 Frequency Stability Measurement ...................................................................................................... 45 4.3.1 Limits of Frequency Stability Measurement ............................................................................. 45 4.3.2 Test Procedure ......................................................................................................................... 45 4.3.3 Test Setup .............................................…

Text truncated - open the document above for the full version.

Report No.: RF181126C15B-1 Page No. 1 / 164 Report Format Version: 6.1.1 Reference No.: 200611C05 FCC Test Report (PART 24) Report No.: RF181126C15B-1 FCC ID: N7NHL78 Test Model: HL7800 Received Date: Jun. 01, 2020 Test Date: Jun. 01 ~ Jun. 12, 2020 Issued Date: Jul. 09, 2020 Applicant: Sierra Wireless Inc. Address: 13811 Wireless Way, Richmond, BC, Canada V6V3A4 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim any endorsement by TAF. Report No.: RF181126C15B-1 Page No. 2 / 164 Report Format Version: 6.1.1 Reference No.: 200611C05 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Test Site and Instruments ..................................................................................................................... 7 3 General Information ................................................................................................................................... 8 3.1 General Description of EUT .................................................................................................................. 8 3.2 Configuration of System under Test .................................................................................................... 10 3.2.1 Description of Support Units ..................................................................................................... 10 3.3 Test Mode Applicability and Tested Channel Detail ............................................................................. 11 3.4 EUT Operating Conditions .................................................................................................................. 17 3.5 General Description of Applied Standards .......................................................................................... 17 4 Test Types and Results ............................................................................................................................ 18 4.1 Output Power Measurement ............................................................................................................... 18 4.1.1 Limits of Output Power Measurement ...................................................................................... 18 4.1.2 Test Procedures ........................................................................................................................ 18 4.1.3 Test Setup ................................................................................................................................. 19 4.1.4 Test Results .............................................................................................................................. 20 4.2 Modulation Characteristics Measurement .......................................................................................... 45 4.2.1 Limits of Modulation Characteristics ......................................................................................... 45 4.2.2 Test Setup ................................................................................................................................. 45 4.2.3 Test Procedure ......................................................................................................................... 45 4.2.4 Test Results .............................................................................................................................. 46 4.3 Frequency Stability Measurement ...................................................................................................... 48 4.3.1 Limits of Frequency Stability Measurement ............................................................................. 48 4.3.2 Test Procedure ......................................................................................................................... 48 4.3.3 Test Setup .......................................…

Text truncated - open the document above for the full version.

Report No.: RF181126C15B-2 Page No. 1 / 269 Report Format Version: 6.1.1 Reference No.: 200611C05 FCC Test Report (PART 27) Report No.: RF181126C15B-2 FCC ID: N7NHL78 Test Model: HL7800 Received Date: Jun. 01, 2020 Test Date: Jun. 02 ~ Jun. 15, 2020 Issued Date: Jul. 09, 2020 Applicant: Sierra Wireless Inc. Address: 13811 Wireless Way, Richmond, BC, Canada V6V3A4 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim any endorsement by TAF. Report No.: RF181126C15B-2 Page No. 2 / 269 Report Format Version: 6.1.1 Reference No.: 200611C05 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 8 2.2 Test Site and Instruments ..................................................................................................................... 9 3 General Information ................................................................................................................................. 10 3.1 General Description of EUT ................................................................................................................ 10 3.2 Configuration of System under Test .................................................................................................... 13 3.2.1 Description of Support Units ...........................................................…

Text truncated - open the document above for the full version.