VG5WIN5025Subscriber unit transceiver

User’s Manual & Installation Guide for: WiN52XX/WiN51XX Series Outdoor CPE ALL RIGHTS RESERVED Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of RuggedCom Inc. Disclaimer Of Liability We have checked the contents of this manual against the hardware and software described. However, deviations from the description cannot be completely ruled out. RuggedCom shall not be liable for any errors or omissions contained herein or for consequential damages in connection with the furnishing, performance, or use of this material. The information given in this document is reviewed regularly and any necessary corrections will be included in subsequent editions. We appreciate any suggested improvements. We reserve the right to make technical improvements without notice. Registered Trademarks RuggedMAX-BST™, RuggedServer™, RuggedWireless™, RuggedCom Discovery Protocol™ (RCDP™), RuggedExplorer™, Enhanced Rapid Scanning Tree Protocol™ (eRSTP™), are trademarks of RuggedCom Inc. Rugged Operating System® (ROS®) and RuggedSwitch® are registered trademarks of RuggedCom Inc. Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the owner. Warranty Five (5) years from date of purchase, return to factory. For warranty details, visit www.ruggedcom.com or contact your customer service representative. Contacting RuggedCom Corporate Headquarters US Headquarters Europe Headquarters RuggedCom Inc 30 Whitmore Road Woodbridge, Ontario Canada, L4L 7Z4 Tel: (905) 856-5288 Fax: (905) 856-1995 Toll-free: 1 (888) 264-0006 RuggedCom 1930 Harrison St., Suite 209 Hollywood, Florida USA, 33020 Tel: (954) 922-7938x103 Fax: (954) 922-7984 Toll-free: 1 (888) 264-0006 RuggedCom Unit 41, Aztec Centre, Aztec West, Almondsbury, Bristol United Kingdom BS32 4TD Tel: +44 1454 203 404 Fax: +44 1454 203 404 Toll-free: 1 (888) 264-0006 Email: [email protected] WiN5200 Table of Contents | 3 Table of Contents Introduction............................................................................................................6 1.1 About this Manual......................................................................................................................7 1.2 General Description..................................................................................................................7 1.2.1 Features..........................................................................................................................8 1.3 Package Components and Unpacking.................................................................................8 1.4 Safety Information.....................................................................................................................8 Product Description............................................................................................11 2.1 Introduction...............................................................................................................................12 2.2 IEEE 802.16e Mobile WiMAX Compliance........................................................................13 2.3 Block Diagram..........................................................................................................................14 2.4 Features....................................................................................................................................15 2.4.1 Mobile WiMAX Wave 2 MIMO Features................................................................15 2.4.2 Security..........................................................................................................................17 2.4.3 Time Division Duplexing (TDD)................................................................................20 2.4.4 Coding Rate..................................................................................................................20 2.4.5 Modulation....................................................................................................................20 2.4.6 Convolution Coding Error Correction......................................................................21 2.5 Deployment Models................................................................................................................21 2.5.1 PTP Deployment.........................................................................................................21 2.5.2 PMP Deployment........................................................................................................21 2.5.3 Non Line-of-Sight........................................................................................................21 2.5.4 Channelization.............................................................................................................21 2.6 Service Flows...........................................................................................................................22 2.6.1 Service Flow Classification.......................................................................................22 2.6.2 Dynamic Service Addition.........................................................................................22 2.6.3 Default Service Flows.................................................................................................23 WiN5200 Table of Contents | 4 2.6.4 Scheduling....................................................................................................................23 2.7 Physical Descriptio…

Text truncated - open the document above for the full version.

AQF-70200-09.IR SPECIFICATION DATASHEET Model AWMO-6-0T Section Omnidirectional Antenna Electrical Specifications Frequency band 2500 ~ 2700 MHz Gain > 5.5 dBi Polarization Vertical Horizontal beam width (-3 dB BW) 360° Vertical beam width (-3 dB BW) 24° ± 3° Electrical Tilt (deg) 0° ± 4° Impedance 50 Ω VSWR < 1 : 1.7 Lightning Protection DC ground IMD (@2×37dBm) < -140 dBc Maximum input power 10 Watt Mechanical Specifications Main Dimensions (Diameter / Height) 25Φ × 300mm Weight (Kg) < 0.5 Connector type N - male Down Tilt (deg) N/A Maximum wind speed 60 m/s Temperature () -40 ~ 70 Radome material Fiber glass Mounting interface N/A RoHS compatibility OK APCPCWM_4828539:WP_0000002WP_0000002 APCPCWM_4828539:WP_0000002WP_0000002 AWMO-6-0T (ANTN 0051) Electrical Specifications Mechanical Specifications Frequency band 2500 ~ Main Dimensions 2700 MHz(Diameter / Height) 25Φ × 300mm Gain > 5.5 dBiWeight (Kg) < 0.5 Polarization Vertical Connector type N - male Horizontal beam width (-3 dB BW) 360° Down Tilt (deg) N/A Vertical beam width Maximum wind (-3 dB BW) 24° ± 3° speed 60 m/s Electrical Tilt (deg) 0° ± 4° Temperature (°C) -40 ~ 70 Impedance 50 Ω Radome material Fiber glass VSWR < 1 : 1.7 Mounting interface N/A Lightning Protection DC groundRoHS compatibility OK IMD (@2×37dBm) < -140 dBcCE 0682 OK Maximum input power 10 Watt Environmental Tests Low Temperature IEC 68-2-1 77 h / -55 °C High Temperature IEC 68 2-1 72 h / +71°C Temp. Cycling IEC 68-2-14 1 h / -45°C+70°C Vibration IEC 60721-3-4 30 min/axis Shock Mechanical IEC 60721-3-4 - Humidity ETSI EN300-2-4 T4.1E 144 h / 90 % Water Tightness IEC 529 IP 65 Solar Radiation ASTM G 53 1000 h Flammability UL 94 Class HB Salt spray IEC 68-2-11 Ka 500 h Ice and snow - 25 mm Radial Wind speed survival operation - 220 Km/h 160 km/h 2008-12-09 16:57/192.168.4.205/T080063 2008-12-09 16:57/192.168.4.205/T080063

Antenna Data Sheet MT-344048/ND Page 1 of 2 MT-344048/ND 2.3-2.7GHz 17dBi Dual Slant Subscriber Antenna Specifications MTI PART NUMBER MT – 344048/ND ELECTRICAL REGULATORY COMPLIANCE ETSI EN 302 326-3 V1.1.2(2006-03)DN2-DN3,RoHS,CE 0682 FREQUENCY RANGE 2.3-2.7 GHz GAIN 17 dBi (min) @ 2.3-2.5 GHz, 18 dBi @ 2.5-2.7 GHz VSWR 1.5 : 1 (typ), 1.7:1 (max) BEAMWIDTH AZIMUTH & ELEVATION 21º POLARIZATION Dual Slunt ± 45° CROSS POLARIZATION ETSI EN 302 326-3 V1.1.2 (2006-03) DN2-DN3 SIDE LOBES LEVEL AZIMUTH & ELEVATION ETSI EN 302 326-3 V1.1.2 (2006-03) DN2-DN3 F/B RATIO ETSI EN 302 326-3 V1.1.2 (2006-03) DN2-DN3 PORT-TO-PORT ISOLATION -18 dB (max) , -25 dB (typ) INPUT IMPEDANCE 50 (ohm) INPUT POWER 6W LIGHTNING PROTECTION DC Grounded MECHANICAL DIMENSIONS (LxWxD) 305x305x15mm (max) WEIGHT 1.2 kg (max) CONNECTOR 2 x N-Type Female RADOME Plastic BASE PLATE Aluminum with chemical conversion coating OUTLINE DRAWING See page 2 MOUNTING KIT MT-120018 ENVIRONMENTAL TEST STANDARD LOW TEMPERATURE IEC 68-2-1 DURATION TEMPERTURE NOTES HIGH TEMPERATURE IEC 68-2-2 72 h -55°C - TEMP. CYCLING IEC 68-2-14 72 h +71°C - VIBRATION IEC 60721-3-4 1 h -45°C +70°C 3 Cycles SHOCK MECHANICAL IEC 60721-3-4 30 min/axis - Random4M5 HUMIDITY ETSI EN300-2-4 T4.1E - - 4M5 WATER TIGHTNESS IEC 529 144 h - 95% SOLAR RADIATION ASTAM G53 - - IP64 SALT SPRAY IEC 68-2-11 Ka - - - ICE AND SNOW - 500 h - 25mm Radial WIND SPEED SURVIVAL OPERATION - - - 220 Km/h 160 Km/h WIND LOAD SUR. FRONT TH. SIDE THRUST - - - 26.6 kg 1.3 kg Antenna Data Sheet MT-344048/ND Page 2 of 2 2.3-2.7 GHz 17 dBi Dual Slant Subscriber Antenna Azimuth Radiation Pattern Midband Freq. 2.4 GHz Elevation Radiation Pattern Midband Freq. 2.4 GHz Dimensions [mm] Existing Antenna Versions MTI Wireless Edge is certified according to ISO 9001 and ISO 14001. WAIVER! While the information contained in this document has been carefully compiled to the best of our present knowledge, it is not intended as presentation or warranty of any kind on our part regarding the fitness of the products concerned for any particular use or purpose and neither shall any statement contained herein be construed as a recommendation to infringe any industrial property rights or as a license to use any such rights. The fitness of each product for any particular purpose must be checked beforehand with our specialists. MTI Wireless Edge Ltd. 11 Hamelacha St. Afek Industrial Park Rosh Ha'ayin 48091, Israel Tel: +972-3-9008900 Fax: +972-3-9008901 www.mtiwe.com MT-344048/ND Document No: Uncontrolled Copy Issued: 17/07/2008

FCC FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY (DoC) Equipment: Subscriber unit Trademark(s) and Model(s): WIN5125-AC,WIN5125-DC,WIN5225 Manufacturer: Ruggedcom Inc. FCC 10 in case other parts of this VG5WIN5025 equipment are subject to certification: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following test reports are subject to this declaration: Test report number: RUGEMC_FCC.21080 Issue date: Aug. 27, 2010 The following manufacturer/importer/entity (located in the USA) is responsible for this declaration: Company name RuggedCom Inc. Namerritle (legal representative) Joe Gould - VP of Sales - Americas Address: 1930 Harrison St. Phone: 954-922-7938 Fax: 954-922-7984 E-mail: [email protected] Date: 9/16/10 Signature:

RF_160, Issue 02 Declaration of Authorization We Name: Ruggedcom Inc. (Corporate Headquarters), Address: 300 Applewood Crescent, Unit 1, City: Concord, Ontario L4K 5C7 Country: Canada ........................................................................... . Declare that: Name Representative of agent: ............. (1) Agent Company name: Hermon Laboratories Ltd. Address: Harakevet Industrial Zone City: Binyamina 30500 Country Israel Is authorized to apply for Certification of the following product(s): Product description: ... CPE Radio Station (subscriber unit) Type designation: WIN5125, WiN5225 Trademark: RuggedMax On our behalf. Date: August 30, 2010 Name: Dudi Magen ........................ .. (2) Function: HW&RF Group Manager Signature: Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

August 11, 2010 To whom it may concern: Being the current FCC contact person on record for RuggedCom Inc.(Concord, Ontario office), I am authorizing Dudi Magen (also employed by RuggedCom Inc., Israel office) to act on my behalf as the FCC registered signee for current RuggedCom wireless submissions. This means that Dudi Magen has my approval and authorization to sign off on all relevant FCC documentation for RuggedCom Inc. Please don’t hesitate to contact me if there is any further clarification needed on the information presented above. Regards, Phil Levy, P. Eng. Manager, Software Engineering RuggedCom Inc. Tel: (905) 482-4549 Email: [email protected] RuggedCom Inc. Tel: (905) 856-5288 300 Applewood Cres Fax: (905) 856-1995 Concord, Ontario Toll-Free: (888) 264-0006 Canada, L4K 5C7 www.RuggedCom.com

Company Name: Ruggedcom Inc. Address : 300 Applewood Crescent, Unit 1, City: Concord, Ontario L4K 5C7 Country: Canada To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: VG5WIN5025 Reference number: 21080 Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Planned Release Date STC: (notes 2, 3, 4, 5) Date: August 30, 2010 Name and signature of applicant: Dudi Magen Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Ruggedcom Inc. FCC ID:VG5WIN5025 Page 1 of 11 EXTERNAL PHOTOGRAPHS This document contains 10 photographs Ruggedcom Inc. FCC ID:VG5WIN5025 Page 2 of 11 Photograph No.1 Subscriber fixed unit WiN5125-AC general view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 3 of 11 Photograph No.2 Subscriber fixed unit WiN5125-AC front view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 4 of 11 Photograph No.3 Subscriber fixed unit WiN5125-AC bottom view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 5 of 11 Photograph No.4 Subscriber mobile unit WiN5125-DC general view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 6 of 11 Photograph No.5 Subscriber mobile unit WiN5125-DC front view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 7 of 11 Photograph No.6 Subscriber mobile unit WiN5125-DC bottom view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 8 of 11 Photograph No.7 Subscriber fixed unit bottom view with integrated panel antenna, WiN5225 Ruggedcom Inc. FCC ID:VG5WIN5025 Page 9 of 11 Photograph No.8 Subscriber fixed unit top view with integrated panel antenna, WiN5225 Ruggedcom Inc. FCC ID:VG5WIN5025 Page 10 of 11 Photograph No.9 Subscriber fixed unit top view without antenna, WiN5225 Ruggedcom Inc. FCC ID:VG5WIN5025 Page 11 of 11 Photograph No.10 Subscriber fixed unit front view with integrated panel antenna, WiN5225

Ruggedcom Inc. FCC ID:VG5WIN5025 Page 1 of 2 Label Ruggedcom Inc. FCC ID:VG5WIN5025 Page 2 of 2 Label location A subscriber unit shall bear the label with FCC ID:VG5WIN5025 on a side panel as shown in the photo below: Label will be placed here.

Ruggedcom Inc. FCC ID:VG5WIN5025 Page 1 of 15 INTERNAL PHOTOGRAPHS This document contains 14 photographs Ruggedcom Inc. FCC ID:VG5WIN5025 Page 2 of 15 Photograph No.1 Subscriber fixed unit WiN5125-AC internal view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 3 of 15 Photograph No.2 Subscriber mobile unit WiN5125-DC internal view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 4 of 15 Photograph No.3 Subscriber fixed unit WiN5225 internal view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 5 of 15 Photograph No.4 Subscriber fixed unit WiN5125-AC/mobile unit WiN5125-DC, RF PCB front view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 6 of 15 Photograph No.5 Subscriber fixed unit WiN5125-AC/mobile unit WiN5125-DC, RF PCB bottom view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 7 of 15 Photograph No.6 WiN5125-AC/ WiN5125-DC, RF PCB front view without shields Ruggedcom Inc. FCC ID:VG5WIN5025 Page 8 of 15 Photograph No.7 WiN5125-AC/ WiN5125-DC, RF PCB bottom view without shields Ruggedcom Inc. FCC ID:VG5WIN5025 Page 9 of 15 Photograph No.8 Subscriber fixed unit WiN5225, RF PCB front view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 10 of 15 Photograph No.9 Subscriber fixed unit WiN5225, RF PCB bottom view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 11 of 15 Photograph No.10 Subscriber fixed unit WiN5225, RF PCB without shield Ruggedcom Inc. FCC ID:VG5WIN5025 Page 12 of 15 Photograph No.11 Subscriber unit WiN5125-AC/WiN5125-DC/WiN5225, PSU PCB front view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 13 of 15 Photograph No.12 Subscriber unit WiN5125-AC/WiN5125-DC/WiN5225, PSU PCB bottom view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 14 of 15 Photograph No.13 Subscriber unit WiN5125-AC/WiN5125-DC/WiN5225, digital PCB front view Ruggedcom Inc. FCC ID:VG5WIN5025 Page 15 of 15 Photograph No.14 Subscriber unit WiN5125-AC/WiN5125-DC/WiN5225, digital PCB bottom view

Ruggedcom Inc. FCC ID:VG5WIN5025 Page 1 of 1 Environmental evaluation and exposure limit according to FCC CFR 47part 1, §1.1307, §1.1310 1) The calculation was done to confirm compliance with power density limit at 20 cm distance for subscriber mobile unit. Limit for power density for general population/uncontrolled exposure is 1 mW/cm 2 for 1500 -100000 MHz frequency range: The power density P (mW/cm 2 ) = P T / 4π r 2 , where P T is the maximum equivalent isotropically radiated power (EIRP). The peak output power of 25.2 dBm with 6 dBi antenna gain corresponds to the equivalent isotropically radiated power (EIRP) of 25.2 dBm + 6 dBi = 31.2 dBm, which is equal to 1318 mW. The power density at 20 cm calculated as follows: 1318 mW / 4π (20 cm) 2 = 0.26 mW/cm 2 < 1 mW/cm 2 General public cannot be exposed to dangerous RF level. 2) To confirm compliance with a safe distance for subscriber fixed unit the following calculation was done: The EIRP is 25.2 dBm + 18 dBi = 43.2 dBm, which is equal to 20892 mW. The minimum safe distance “r”, where RF exposure does not exceed FCC permissible limit, is r = sqrt { P T / (Px4π)} = sqrt {20892 / 12.56} = 41 cm << 2 m . General public cannot be exposed to dangerous RF level.

Hermon Laboratories Ltd. Harakevet Industrial Zone, Binyamina 30500, Israel Tel. +972-4-6288001 Fax. +972-4-6288277 E-mail: [email protected] Page 1 of 173 Report ID: RUGRAD_FCC.21080.doc Date of Issue: 8/17/2010 Electrical 839.01 TEST REPORT ACCORDING TO: FCC 47 CFR part 27 FOR: Ruggedcom Inc. Subscriber unit operating in 2496 - 2690 MHz Models: WIN5125-AC, WIN5125-DC, WIN5225 This report is in conformity with ISO/ IEC 17025. The "A2LA Accredited" symbol endorsement applies only to the tests and calibrations that are listed in the scope of Hermon Laboratories accreditation. The test results relate only to the items tested. This test report shall not be reproduced in any form except in full with the written approval of Hermon Laboratories Ltd. Report ID: RUGRAD_FCC.21080.doc Date of Issue: 8/17/2010 Page 2 of 173 Table of contents 1 Applicant information..................................................................................................................................................... 3 2 Equipment under test attributes .................................................................................................................................... 3 3 Manufacturer information .............................................................................................................................................. 3 4 Test details.................................................................................................................................................................... 3 5 Tests summary.............................................................................................................................................................. 4 6 EUT description............................................................................................................................................................. 5 6.1 General information....................................................................................................................................................... 5 6.2 EUT modules and sub-assemblies................................................................................................................................ 5 6.3 Ports and lines .............................................................................................................................................................. 5 6.4 Support and test equipment .......................................................................................................................................... 5 6.5 Changes made in the EUT ............................................................................................................................................ 5 6.6 Test configuration.......................................................................................................................................................... 6 6.7 Transmitter characteristics ............................................................................................................................................ 8 7 Transmitter tests according to 47CFR part 27 requirements......................................................................................... 9 7.1 Peak output power test.................................................................................................................................................. 9 7.2 Peak output power test................................................................................................................................................ 12 7.3 Occupied bandwidth test ............................................................................................................................................. 15 7.4 Occupied bandwidth test ............................................................................................................................................. 32 7.5 Emission mask test ..................................................................................................................................................... 49 7.6 Emission mask test ..................................................................................................................................................... 65 7.7 Radiated spurious emission measurements................................................................................................................ 81 7.8 Radiated spurious emission measurements................................................................................................................ 97 7.9 Spurious emissions at RF antenna connector test .................................................................................................... 113 7.10 Spurious emissions at RF antenna connector test .................................................................................................... 135 7.11 Frequency stability test.............................................................................................................................................. 157 8 APPENDIX A Test equipment and ancillaries used for tests..................................................................................... 160 9 APPENDIX B Measurement uncertainties................................................................................................................. 162 10 APPENDIX C Test laboratory description ................................................................................................................. 163 11 APPENDIX D Specification references ..................................................................................................................... 163 12 APPENDIX E Test equipment correction factors....................................................................................................... 164 13 APPENDIX F Abbreviations and acronyms..........................................................…

Text truncated - open the document above for the full version.

Ruggedcom Inc. FCC ID:VG5WIN5025 Page 1 of 10 SETUP PHOTOGRAPHS This document contains 9 photographs Ruggedcom Inc. FCC ID:VG5WIN5025 Page 2 of 10 Photograph No.1 Peak output power measurement setup Ruggedcom Inc. FCC ID:VG5WIN5025 Page 3 of 10 Photograph No.2 Occupied bandwidth measurement setup Ruggedcom Inc. FCC ID:VG5WIN5025 Page 4 of 10 Photograph No.3 Emission mask, conducted spurious emissions measurement setup Ruggedcom Inc. FCC ID:VG5WIN5025 Page 5 of 10 Photograph No.4 Spurious emissions measurement setup in the anechoic chamber below 30 MHz Ruggedcom Inc. FCC ID:VG5WIN5025 Page 6 of 10 Photograph No.5 Spurious emissions measurement setup in the anechoic chamber in 30 -1000 MHz Ruggedcom Inc. FCC ID:VG5WIN5025 Page 7 of 10 Photograph No.6 Spurious emissions measurement setup in the anechoic chamber above 1000 MHz Ruggedcom Inc. FCC ID:VG5WIN5025 Page 8 of 10 Photograph No.7 Radiated spurious emissions measurement setup at the OATS above 1000 MHz Ruggedcom Inc. FCC ID:VG5WIN5025 Page 9 of 10 Photograph No.8 Frequency stability measurement setup Ruggedcom Inc. FCC ID:VG5WIN5025 Page 10 of 10 Photograph No.9 Conducted emissions measurement on AC line setup