VGAYCWU7BM3Transmitter

Arming the Security System Security System Armed and Activated Disarming the Security System The Valet Switch And Valet Mode The Red LED Status Light Optional Pre-Warning Shock Detection Circuit Programmable Features This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equip

1 Helen Zhao Subject:FW: FW: BIG KING HORN SPEAKER ENT.CO.,LTD., FCC ID: VGAYCWU7BM3, Assessment NO.: AN07T6994, Notice#1 Exhibit-C-Test_Rep ort.rev..pdf... Exhibit-F-Setup_Ph otos.rev..pd... From: Iris Lin Sent: Tuesday, July 10, 2007 10:50 PM To: Helen Zhao Cc: S. S. Liou (E-mail) Subject: Re: FW: BIG KING HORN SPEAKER ENT.CO.,LTD., FCC ID: VGAYCWU7BM3, Assessment NO.: AN07T6994, Notice#1 Dear Charvey, 1. Please refer to the updated "1.3 Methodology" in the attached report sheet 1 of 20 sheets. 2. We have revise the "Operation mode" in the attached report sheet 8 of 20 sheets. In the tesr report sheet 6 of 20 sheets 4.2 Measurement Procedure, it includes the explanation of three test orientation and the worst case was recorded. 3. Please refer to the attached set up photo for your reference. ELECTRONICS TESTING CENTER, TAIWAN IRIS LIN -----Original Message----- Sent: Tuesday, July 10, 2007 4:51 PM Subject: BIG KING HORN SPEAKER ENT.CO.,LTD., FCC ID: VGAYCWU7BM3, Assessment NO.: AN07T6994, Notice#1 Question #1: The test report does not indicate which version of the ANSI C63.4 has been used for testing. Please verify that the newest version, ANSI C63.4:2003 has been used and submit an updated test report indicating which version was used. Question #2: The test setup photos in the test report do not show any means of re-orienting this device in the X, Y & Z orientations during test. Please explain how the EUT was reoriented during the testing. Question #3: The test setup photos exhibit shows internal photos. Please resubmit test setup photos. Best Regards, Helen Zhao 2 The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender.

ETC Report No.:07-06-RBF-093 FCC ID.: VGAYCWU7BM3 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Top View of EUT Side View of EUT ETC Report No.:07-06-RBF-093 FCC ID.: VGAYCWU7BM3 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Front View of EUT Side View of EUT ETC Report No.:07-06-RBF-093 FCC ID.: VGAYCWU7BM3 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Rear View of EUT Bottom View of EUT

Model : T-U7BM3 FCC ID : VGAYCWU7BM3 22 mm 12mm

ETC Report No.:07-06-RBF-093 FCC ID.: VGAYCWU7BM3 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Internal View of EUT ETC Report No.:07-06-RBF-093 FCC ID.: VGAYCWU7BM3 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT Component View of Main PCB Solder View of Main PCB

ETC Report No.:07-06-RBF-093 FCC ID.: VGAYCWU7BM3 Rev. No 1.0 Radiated Measurement Photos