W89-SMARTKID-49TR/C City Racer

Portable System With Bluetooth Connection VP-168B INSTRUCTION MANUAL WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT SAFETYINSTRUCTIONS 1. Read these instructions 2. Keep these instructions 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments / accessories specified by the manufacturer. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be placed on the apparatus. 16. Mains plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely. 17. Battery shall not be exposed to excessive heat such as sunshine, fire or the like. 18. Do not overload wall outlet. Use only power source as indicated. 19. Do not attempt to dismantle, open or repair this product yourself. If a fault occurs, seek advice from your local qualified service technician or contact the distributor via the telephone number at the back of this instruction manual. 20. Caution marking and nameplate are located on back of product FCC Statement : This device complies with Part of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. WARNING : MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNAL IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. Location of controls 1) Skip up button 2) Power LED indicator 3) Bluetooth indicator 4) FM stereo LED indicator 5) BT Disconnect button 6) Play/pause button 7) Tuning knob 8) Handle 9) Level meter 10) Dial scale 11) Treble knob 12) Skip down button 13) Bass knob 14) 3.5 mm headphone jack 15) Aux in jack 16) Off/functions selector 17) Band switch 18) Volume button 19) FM wire antenna 20) Battery Compartment 21) AC socket Caution: Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This unit should not be adjusted or repaired by anyone except qualified service personnel. Precautions for use Installation  Unpack all parts and remove protective material.  Do not connect the unit to the mains before checking the mains voltage and before all other connections have been made.  Do not cover any vents and make sure that there is a space of several centimeters around the unit for ventilation. AC Connection 1. Connect the one end of the detachable power cord to the AC socket (21) and the other end to the AC outlet. 2. When you first plug the unit into the mains, the unit was ready to play music. 3. Turn on the unit by Off/function selector (16), the POWER LED indicator (2) will light up. Battery installation 1. Open the battery door at the rear side of the unit to install the battery. 2. Follow the engraved marking in the compartment to install 8pcs “D” size / UM1 battery with the correct direction to the battery compartment (20). Then cover the battery door. 3. Disconnect the AC cord fro…

Text truncated - open the document above for the full version.

BASS—SPK Earphone Treble/Bass Volume control IC TC9153 Pre-Amp IC SC1308 Sub- woofer pre-Amp TUNER Channel IC TC 4052P SI 4730 L/R_SPK Power Amp IC TDA7377 AUX/BLUETOOTHLevel LED driver IC BKS-138-185 VP-168B block diagram BT EDR The emitter ClockPMU CPU RAMROMAudioEngine IO AudioDAC System Power LED Speaker EEPROM UART TO PC BKS TECHNOLOGY LTD2013-03-12BM84/BM81 The receiver

GOLDSOUND ELECTRONIC. LTD. Flat 13, 3/F., Tel. : (852) 2191 2681 Hewlett Centre., Fax.: (852) 2191 3781 54 Hoi Yuen Road., Kwun Tong e-mail : [email protected] Hong Kong "I, an officer of Goldsound Electroncis do hereby authorize Intertek Testing Services (Mr. Terry Chan) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and Part 18 of the FCC Rules until further notice." I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.,862. Dated this day of 2013-July-30 By Signature : Printed Name : Raymond Tse Title : Engineer Remark: The person who signs this authorization letter must be the grantee contact of record in the Grantee Code data base

INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (External) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (External) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (External)

FM ANT OPENOPEN RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING:SHOCK HAZARD-DO NOT OPEN AVIS:RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR DO NOT ALLOW THIS PRODUCT TO BE EXPOSED TO RAIN OR MOISTURE AC serial nr. PRODUCT COMPLIES WITH DHHS RULES 21 CFR - SUBCHAPTER J - APPLICATION DATE OF MANUFACTURE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The label shall read as follows: WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. DHHS Label Dim:43 x 9 mm Black Text on White background FCC Label Dim:95 x 14 mm Black Text on White background Rating Label Dim: 70 x 35mm White text on Black background Serial No. Label Black Text on White background Model: BT168GB Distributed by Electro Brand Inc. Westchester, IL 60154 MADE IN CHINA FCC ID:RQU-VP-168B CONFORMS TO ANSI/UL STD. 60065 Portable system with Bluetooth connect FM 88 - 108 MHZ AM 540 - 1700 KHZ AC 120V 60Hz, 53 W DC 8 x 1.5V / ’D’ Size / R20 / UM-1 Model: BT168GB Distributed by Electro Brand Inc. Westchester, IL 60154 MADE IN CHINA FCC ID:RQU-VP-168B CONFORMS TO ANSI/UL STD. 60065 Portable system with Bluetooth connect FM 88 - 108 MHZ AM 540 - 1700 KHZ AC 120V 60Hz, 53 W DC 8 x 1.5V / ’D’ Size / R20 / UM-1

INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal) INTERTEK TESTING SERVICE Report No.: 13061472HKG-001 FCC ID: RQU-VP-168B Equipment Photographs Model : VP-168B (Internal)

Technical Description The Equipment Under Test (EUT) is a Portable System with Bluetooth connection. It can accept both analog input sources (FM radio play and 3.5mm headphone-jack in), and wireless Bluetooth device. The Bluetooth module is operating in the frequency range from 2402MHz to 2480MHz (79 channels with 1MHz channel spacing). The EUT is powered by 120VAC. 2.4GHz Bluetooth Module: Modulation Type: GFSK Antenna Type: Integral, Internal (PCB Trace) Frequency Range: 2402MHz - 2480MHz, 1MHz channel spacing, 79 channels Nominal field strength is 93.8dB ȝV/m @ 3m Production Tolerance of field strength is +/- 3dB Antenna gain is 0dBi The functions of main ICs are mentioned below. 1. BlueTooth module BM81SPK01 (U507): 1) U1 (IS1684S) acts as the 2.4GHz radio core of Bluetooth module (U2) (BM81SPK01NB2), which is integrating with audio CODEC. 2) 16MHz crystal (X1) provides clock for Bluetooth RF IC IS1681S (U1). 3) U2 (24C32) is serial EEPROM for parameter backup of U1 (IS1681S). 2. Power Supply portion: 1) Regulator for RF module: ICYT81117T3.3V 3. Control MCU: 1) IC1 SC9671B 4. Linear Integrated Circuit 1) IC505 TC9153 5. Dual Operational Amplifier 1) IC506. IC508 UTC4558 6. Power Amplifier 1) IC503 TDA7377 7. Multiplexer 1) IC509 TC4052P 8. Broadcast FM radio Tuner 1) U500 SI4831-B Channel Frequency Table of Bluetooth Module Preliminary Datasheet BM81SPK01 Version:0.92 9/20/2011 1 BM81SPK01 Bluetooth 3.0+EDR Wireless Speaker Module Version: 0.92 - 2 - 9/20/2011 Product Description The ISSC BM81SPK01 is a highly integrated Bluetooth 3.0+EDR stereo module, designed for high data rate, short-range wireless communication in the 2.4 GHz ISM band. With ISSC Bluetooth stack and profile, the ISSC BM81SPK01 provides a low power and ultra-low cost Bluetooth 3.0+EDR solution for wireless voice/audio applicati ons. Features
Main Chip: ISSC IS1684S
Bluetooth 3.0+EDR compliant
Typical +2dBm Class 2 output power
Receiver Sensitivity: GFSK typical -91dBm, π/4 PSK typical -92dBm, 8DPSK typical -84dBm
Piconet and Scatter net support
HCI UART interface
CVSD , A-law, μ-law CODEC algorithms for voice applications
SBC decode for Bluetooth audio streaming
Build-in High performance stereo audio codec
Cap-less/single end headphone driver
Audio DAC: 94dB SNR
Build in Max. 350mAH Li-ion battery charger
HSP, HFP, A2DP, AVRCP profile support
3V operating voltage
ROM version: 32Kb EEPROM
34 pins for DIP module, 35pins for SMT module (with additional 35th pin antenna port for external antenna option)
Size: 15mm x29mm
Build-in PCB Antenna
RoHS compliant Preliminary Datasheet BM81SPK01 Version: 0.92 - 3 - 9/20/2011 Device Pinout Diagram P02 27 AIL 13 P27 28 MIC_BIAS 11 SPKR 5 P30 1 P00 3 AGND 8 P20 2 SYS_PWR 19 MIC1_P 9 GND 21 VDD_IO 15 P24 25 RST 14 P01 33 P16 32 P22 26 P05 29 HCI_TXD 30 P04 4 HCI_RXD 31 MFB 22 SPKL 6 BT_RF 35 VDDA 7 GND 34 BAT_IN 17 MIC1_N 10 LED1 23 ADAP_IN 16 AIR 12 SK1/P03 18 LED2 24 BK_OUT 20 Preliminary Datasheet BM81SPK01 Version: 0.92 - 4 - 9/20/2011 Pin Definition Pin No. I/O Name Description 1 P P30 GPIO, default pull-high input Line-in detection, 1: no line-in detected; 0: line-in detected 2 I/O P20 GPIO, default pull-high input System Configuration, H: Application L: Baseband(IBDK Mode) 3 I/O P00 GPIO, default pull-low input. Slide Switch Detector 4 I/O P04 GPIO, default pull-high input Audio AMP Enable 5 AOSPKR R-channel analog headphone output, single-ended application only 6 AOSPKL L-channel analog headphone output, single-ended application only 7 AP VDDA Reserve for external cap to fine tune audio frequency response 8 AP AGND Audio ground 9 AI MIC1_P Mic 1 mono differential analog positive input 10 AI MIC1_N Mic 1 mono differential analog negative input 11 AP MIC_BIASMicrophone biasing voltage 12 AI AIR Stereo analog line in, R-channel 13 AI AIL Stereo analog line in, L-channel 14 I/O RST_N System Reset Pin 15 P VDDIO VDDIO pin, for calibration only Do not add external power to this pin 16 P ADAP_IN Power adaptor input 17 P BAT_IN Battery input 18 I/O SK1/P03 Default SAR input for battery detection This pin can be re-defined as GPIO P03 19 P SYS_PW System Power Output 20 P BK_OUT Buck feedback sense pin 21 P GND Digital ground Preliminary Datasheet BM81SPK01 Version: 0.92 - 5 - 9/20/2011 22 P MFB Multi-Function Push Button key Combined Play/Pause key when A2DP enabled. 23 P LED1 LED Driver 1 24 P LED2 LED Driver 2 25 I/O P24 GPIO, default pull-high input System Configuration, H: Boot Mode 26 I/O P22 GPIO, default pull-low input. External LDO enable 27 I/O P02 GPIO, default pull-high input PLAY/PAUSE button 28 I/O P27 GPIO, default pull-high input Foward button 29 I/O P05 GPIO, default pull-high input REW button 30 OHCI_TXD HCI TX data 31 I HXI_RXD HCI RX data 32 I/O P16 GPIO, default pull-high input Volumn down button 33 I/O P01 GPIO, default pull-high input Volumn up button 34 P GND Digital ground 35 AIOBT_RF NC for on board PCB antenna Antenna matching if an external antenna is used Preliminary Datasheet BM81SPK01 Version: 0.92 - 6 - 9/20/2011 Outline Dimension (Module Foot print) Preliminary Datasheet BM81SPK01

Analysis Report Report No.: 13061472HKG-001 The Equipment Under Test (EUT) is a Portable System with Bluetooth connection. It can accept both analog input sources (FM radio play and 3.5mm headphone-jack in), and wireless Bluetooth device. The Bluetooth module is operating in the frequency range from 2402MHz to 2480MHz (79 channels with 1MHz channel spacing). The EUT is powered by 120VAC. Antenna Type: Internal integral (PCB Trace) Antenna Gain: 0dBi Nominal rated field strength: 93.8dBμV/m at 3m Maximum allowed field strength of production tolerance: -/+3 dB According to the KDB 447498: Based on the Maximum allowed field strength of production tolerance was 96.8dBμV/m at 3m in frequency 2.4GHz, thus; The EIRP = [(FS*D) ^2*1000 / 30] = 1.436mW Conducted power = Radiated Power (EIRP) - Antenna Gain So; Conducted Power = 1.436mW. The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.53 mWm Since the above conducted output power is well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing.

5 5 4 4 3 3 2 2 1 1 DD CC BB AA P12 P13 P24 MFB HCI_RXD P27 HCI_TXD P05 P22 P01 P16 P02 LED1 HCI_TXD SPKLP16 P30P04P01 P22 SPKR P05 P13 P12 P20 LED2 RST_N P02 P24 AOHPM HCI_RXD P35P00 P27AIR AIL LED2 RST_N AIL AIR SPKL SPKR P04 P00 P20 P30 AOHPM MFB LED1 P35 BT RF BT RF VDD_IO VDD_IO SYS_PWR 1V8 BAT_IN ADAP_IN BK_OUT 1V8 BK_OUT SYS_PWR CODEC_VO VDD_IO VDD_IO VDD_IO CODEC_VO CODEC_VIN CODEC_VIN ADAP_IN BAT_IN 1V8 SYS_PWR BK_OUT 1V8 VDD_IO Board Name Size TitleRev Date:Sheetof P/N BM84SPK01 BM84SPK01 ISSC Technologies Corp. ADD. 4F, No.8, Dusing Rd., Hsinchu Science Park, Hsinchu City 30078, Taiwan TEL. 886-3-5778385 B 11Wednesday, July 25, 2012 Board Name Size TitleRev Date:Sheetof P/N BM84SPK01 BM84SPK01 ISSC Technologies Corp. ADD. 4F, No.8, Dusing Rd., Hsinchu Science Park, Hsinchu City 30078, Taiwan TEL. 886-3-5778385 B 11Wednesday, July 25, 2012 Board Name Size TitleRev Date:Sheetof P/N BM84SPK01 BM84SPK01 ISSC Technologies Corp. ADD. 4F, No.8, Dusing Rd., Hsinchu Science Park, Hsinchu City 30078, Taiwan TEL. 886-3-5778385 B 11Wednesday, July 25, 2012 EEPROM 24C32 PIN DEFINATION GPIO Description P00 P22 P04 P27 P16 P24 P05 P20 Slide Switch Detect/TX_IND REV Audio AMP Enable FWD Play/Pause System Configuration System Configuration Keep alive for external LDO P01 P02 Volume up Volume down P03RX_IND A0 1 A1 2 A2 3 GND 4 SDA 5 SCL 6 WP 7 VCC 8 U2 ACE24C32 U2 ACE24C32 C11 1u/10V C11 1u/10V C18 10u/10V C18 10u/10V C4 1u/10V C4 1u/10V C10 10u/10V C10 10u/10V C19 0.1u/16V C19 0.1u/16V C5 0.75p/50V C5 0.75p/50V C7 10p/50V C7 10p/50V 12 R6 1R R6 1R L12.2nHL12.2nH 4 1 3 2 X1 X4P-16MHZ X1 X4P-16MHZ 1 2 R1 0 R1 0 C9 NP C9 NP C3 1p/50V C3 1p/50V 1 2 R5 1K R5 1K 1 2 R8 1K R8 1K C20 NP C20 NP 12 FB1 FB-0402 FB1 FB-0402 C17 1u/10V C17 1u/10V L3 L22uH L3 L22uH C15 10u/10V C15 10u/10V VDDAO 1 AOHPM 2 VSSAO 3 AOHPL 4 VDDA 5 VSSA 6 VCOM 7 AIR 8 AIL 9 NC 10 VDD_IO 12 RST_N 13 P1_2 14 P1_3 15 CODEC_VO 18 3V1_IN 19 ADAP_IN 20 BAT_IN 21 SAR_VDD 23 SYS_PWR 24 BK_VDD 25 BK_LX 26 XO_N 42 XO_P 41 VDD_IO 40 HCI_RXD 38 HCI_TXD 37 1V8 16 P0_5 36 P0_2 34 P2_4 32 LED2 31 LED1 30 MFB 29 BK_OUT 28 AOHPR 56 1V8 55 EAN 54 VDD_IO 52 P0_0 50 P2_0 49 P3_0 48 P0_3 47 P0_1 46 RTX 45 VCC_RF 43 P3_5 53 P2_7 35 3V1_O 17 GND 57 NC 11 SK1 22 P1_6 39 RX_CLS1 44 P0_4 51 P2_2 33 BK_GND 27 IS1684S-202 U1 IS1684S-202 IS1684S-202 U1 IS1684S-202 TP1 RF-TP1 TP1 RF-TP1 C8 10p/50V C8 10p/50V C14 0.1u/16V C14 0.1u/16V C12 1u/6.3V C12 1u/6.3V C2 2p/50V C2 2p/50V C6 1u/6.3V C6 1u/6.3V 12 R7 1R R7 1R C16 10u/10V C16 10u/10V C13 1u/6.3V C13 1u/6.3V 1 ANT1 ANT-MP8 ANT1 ANT-MP8 C1 1.8p/50V C1 1.8p/50V MIC1_P 10 P00 4 P16 33 MIC1_N 11 MIC_BIAS 12 AIL 14 AIR 13 GND 22 SYS_PWR 20 MFB 23 P24 26 P02 28 P22 27 P27 29 P05 30 HCI_RXD 32 HCI_TXD 31 P01 34 LED2 25 SPKR 6 P20 3 P04 5 BAT_IN 18 SK1_P03 19 ADAP_IN 17 LED1 24 GND 35 BK_OUT 21 P30 2 SPKL 7 VDDA 8 GND 9 RST 15 VDD_IO 16 BT_RF 36 AOHPM 1 FP1 BM84SPK01 FP1 BM84SPK01 12 R9 4K7 R9 4K7 MODE:R-63USB/SD DATE:2012-08-15 3V3 GND L/R NC LED+ LED- 1 DVSS 2 GPB4 3 GPB5 4 GPB6 5 GPB7 6 GPD0 7 GPD1 8 GPA3 9 GPA5 10 NC 11 GPA4 12 GPA2 13 USB_DM 14 USB_DP 15 3V3_OUT 16 5V_IN 17 CORE_VDD 18 XIN 19 XOUT 20 GPD2 21 GPD3 22 GPD4 23 GPD5 24 GPD6 25 GPD7 26 GPB0 27 GPB1 28 GPB2 29 GPB3 30 GPA0 31 GPA1 32 GPC0 33 GPC1 34 GPC2 35 VDD33 36 AVDD33 37 AVSS 38 VREF 39 DAC_RO 40 DAC_LO 41 LINE_R 42 LINE_L 43 GPA6 44 GPA7 45 GPE3 46 GPE2 47 GPE1 48 GPE0 BKS138-185 1 2 X400 32.768KHZ C405 15P C404 15P LED406 GREEN LED401 red LED402 red LED403 red LED404 red LED405 red LED407 GREEN LED408 GREEN R400 220R R401 220R R402 220R R403 220R R404 220R R405 220R R406 220R R407 220R LED414 GREEN LED409 red LED410 red LED411 red LED412 red LED413 red LED415 GREEN LED416 GREEN R408 220R R409 220R R410 220R R411 220R R412 220R R413 220R R414 220R R415 220R C407 104P R420 10K R417 470K C402 220P C400 22P C406 100U C403 104P 1 2 3 4 5 6 CON400 C401 102P R418 47K R419 10K R416 10K LED417 WHITE LED400 WHITE TU- TU+ R L GND 3V3 VCC AUX/R RA/R R/O TA CD/R A B VSS VEE INH RA/L CD/L L/OUT AUX/L TA 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 GND AUX_8V USB_8V GND 8V+ TUNER_8V POWER BAND BT+ ST+ ST- FM AM BT- L GND R V+OU V+IN AUX IN VOL- VOL+ GND 8V VOL- VOL+ GND 8V PLAY/PAUSE SIK+ SIK- disconnect L R L R L R ROUT LOUT G AMP_SW BASS TO:EHPHONE PART L R AGND BASS MUTE POWER GND 12V BASS AMP PART DISCPLAY_KEY.PART PLAY/PAUSE SIK+ SIK- disconnect KEY PART MODE:VP-168 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 IC505 TC9153 C127 4.7UF C130 4.7UF R39 15k R17 15k Q13 8050 Q1 8050 R33 4K7 R36 4K7 R38 1k R37 1k C199 4.7UF C200 4.7UF C114 4.7UF R46 1K C198 4.7UF R151 1K R254 10K R271 10K C116 220UF D33 1N4148 C175 1U R252 100K C115 4.7UF R253 33K D32 1N4148 R259 330R Q8 822B R149 2R2 1/2W R150 220R ZD4 9V1 C162 220UF C174 104P C178 104P C177 220UF C37 47u Q25 9014 Q26 9014 R264 22K R263 22K R265 22K 262 22K C167 2U2 C169 2U2 E B C Q2 9014 E B C Q6 9014 R219 1M R233 1M R223 6K8 C517 220U C172 2U2 C171 2U2 R506 330R R225 180R R230 330R C173 68P C168 68P R226 6K8 E B C Q12 9014 E B C Q10 9014 R134 1M R153 1M R152 6K8 R514 330R R135 330R C63 68P C64 68P R136 330R C508 220U R133 6K8 R227 6K8 R76 10K R78 10K R80 10K R221 33K R231 33K C510 104P R222 10K R75 10K C585 104P C531 682M B50K R234 6K8 R524 4K7 R212 22K C157 682M B50K C160 332M R213 0R C546 682M B50K R281 6K8 R545 4K7 R207 22K C158 682M B50K C161 332M R214 0R CN501 1 GND 2 OUT1 3 IN 4 OUT2 IC REG1117_3 E:HARDESS HARDESS8381ZOUES8381CARD .DSN CYT81117-3.3V R169 10K R171 470K R172 470K R177 1K R170 47K D29 4148 D28 4148 E B C Q23 9014 E B C Q22 8050 C137 102P C138 104P C140 2U2 R158 10R C57 220U C139 104P R174 470K R173 6K8 R175 820K C141 2U2 E B C Q24 9014 R176 3K3 R178 820K R185 2K2 C142 2u2 1 2 3 4 8 7 6 5 IC501 BKS138-177 R62 1K R56 1K R70 100K R69 100K R79 56K C70 203P C32 2U2 E B C Q509 9014 R164 820K R165 4K7 C35 2U2 R156 2K2 C144 2U2 R74 2K2 E B C Q21 9014 R202 6K8 R199 820K R201 1K C143 2U2 E B C Q27 9014 R196 4K7 R200 820K C145 2U2 R197 470K D17 4148 D18 4148 R198 330K 1 2 3 4 5 6 CN502 C136 104P IC502 S1117…

Text truncated - open the document above for the full version.

Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 13061009HKG-001R1 i FCC ID: W89-SMARTKID-49T Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com GENERAL INFORMATION Apple Toys Development Co., Ltd. BRAND NAME: SMART KID, MODEL: 8801-1 8801-2, 8801-3, 8801-4 FCC ID: W89-SMARTKID-49T Grantee: Apple Toys Development Co., Ltd. Grantee Address: Room 515-516, Tower A, 5/F., Peninsula Centre, 67 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Contact Person: Elli Hung Tel: (852) 2367 6128 Fax: (852) 2760 4861 e-mail: N/A Manufacturer: Apple Toys Development Co., Ltd. Manufacturer Address: Room 818, Tower A, Peninsula Centre, 67 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong. Buyer: RadioShack Brand Name: SMART KID Model: 8801-1 Additional Model: 8801-2, 8801-3, 8801-4 Asst. No.: 6000976 Type of EUT: Transmitter Description of EUT: 1:64 Mini RC Racing Car Serial Number: N/A FCC ID: W89-SMARTKID-49T Date of Sample Submitted: June 20, 2013 Date of Test: July 02, 2013 Report No.: 13061009HKG-001R1 Report Date: September 2, 2013 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 13061009HKG-001R1 ii FCC ID: W89-SMARTKID-49T Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com SUMMARY OF TEST RESULT Apple Toys Development Co., Ltd. BRAND NAME: SMART KID, MODEL: 8801-1 8801-2, 8801-3, 8801-4 FCC ID: W89-SMARTKID-49T TEST SPECIFICATION REFERENCE RESULTS Transmitter Field Strength and Bandwidth Requirement 15.235 Pass The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2011 Edition Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 13061009HKG-001R1 iii FCC ID: W89-SMARTKID-49T Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com Table of Contents 1.0 General Description............................................................................................ 1 1.1 Product Description ........................................................................................... 1 1.2 Related Submittal(s) Grants ............................................................................... 1 1.3 Test Methodology .............................................................................................. 1 1.4 Test Facility ....................................................................................................... 1 2.0 System Test Configuration ................................................................................. 2 2.1 Justification........................................................................................................ 2 2.2 EUT Exercising Software ................................................................................... 2 2.3 Special Accessories........................................................................................... 2 2.4 Equipment Modification...................................................................................... 2 2.5 Measurement Uncertainty .................................................................................. 2 2.6 Support Equipment List and Description............................................................. 2 3.0 Emission Results ................................................................................................ 3 3.1 Field Strength Calculation .................................................................................. 3 3.2 Radiated Emission Configuration Photograph .................................................... 4 3.3 Radiated Emission Data .................................................................................... 4 4.0 Equipment Photographs ..................................................................................... 6 5.0 Product Labelling ................................................................................................ 6 6.0 Technical Specifications..............................................................…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No: 13061472HKG-001 FCC ID: RQU-VP-168B Configuration Photogr…

Text truncated - open the document above for the full version.