WL6-TC6BC30CA1Wireless Motherboard

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‰ Reorient or relocate the receiving antenna. ‰ Increase the separation between the equipment and receiver. ‰ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 2 Any changes or modifications not expressly approved by the party responsible for End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: WL6-TC6BC30CA1 Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: This Transmitter must not be co­located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your 3 body. Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCC ID: WL6-TC6BC30CA1 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. 4 Connectors and Pads 1 Audio FPC Connector 2 Battery Pad 3 WiFi/BT/GPS Antenna Pad 4 RF Test Connector 5 TP Connector 5 6 LCD Connector 7 Speaker Pad 8 Mic Pad 9 T-flash Card Connector 10 Side Key Connectors 11 Bear Camera Connector 12 Front Camera Connector 13 Micro USB Connector Main components A CPU+PMIC+DDR+EMMC B WiFi/BT C CODEC D GPS . Antenna Specification Type PIFA Trade name Innetech Model 13H130-JX9070 6 gain 2.85 dBi

1 of 3 External Photos Model Number: MCT02A FCC ID: WL6-TC6BC30CA1 2 of 3 EUT Photo 1 ) EUT Photo 2 ) 3 of 3 EUT Photo 3 ) EUT Photo 4 )

ID Label info & Label Location FCC ID : WL6-TC6BC30CA1

1 of 6 Internal Photos Model Number: MCT02A FCC ID: WL6-TC6BC30CA1 2 of 6 EUT Photo 1 ) EUT Photo 2 ) 3 of 6 EUT Photo 3 ) EUT Photo 4 ) 4 of 6 EUT Photo 5 ) EUT Photo 6 ) 5 of 6 EUT Photo 7 ) EUT Photo 8 ) 6 of 6 EUT Photo 9 )

A Test Lab Techno Corp. Changan Lab：No. 140 -1, Changan Street, Bade City, Taoyuan County, Taiwan R.O.C. Te l：886-3-271-0188 / Fax：886-3-271-0190 MPE Report Test Report No. ： 1408FS11 Applicant ： ELITEGROUP COMPUTER SYSTEMS CO., LTD Manufacturer ： Golden Elite Technology (SHENZHEN) Co., Ltd. Product Type ： Wireless Motherboard Trade Name ： ECS ELITEGROUP Model Number ： MCT02A Date of Received ： Jul. 18, 2014 Test Period ： Aug. 04, 2014 Date of Issued ： Aug. 05, 2014 Test Specification ： 47 CFR § 2.1091 47 CFR §1.1310 ANSI / IEEE Std.C95.1-1992 Location of Test Lab. ： Chang-an Lab. 1. The test operations have to be performed with cautious behavior, the test results are as attached. 2. The test results are under chamber environment of A Test Lab Techno Corp. A Test Lab Techno Corp. does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples. 3. The measurement report has to be written approval of A Test Lab Techno Corp. It may only be reproduced or published in full. This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. 4. This document may be altered or revised by A Test Lab Techno. Corp. personnel only, and shall be noted in the revision section of the document. Approved By ： Tested By ： (Bill Hu) (Sky Chou) Report Number: 1408FS11Page 1 of 7 ©2014 A Test Lab Techno Corp. Contents 1. Description of Equipment under Test (EUT)............................................................... 3 2. Human Exposure Assessment .................................................................................... 4 3. RF Output Power........................................................................................................... 5 4. Test Result.....................................................................................................................7 Report Number: 1408FS11Page 2 of 7 ©2014 A Test Lab Techno Corp. 1. Description of Equipment under Test (EUT) Applicant ELITEGROUP COMPUTER SYSTEMS CO., LTD Applicant Address No.239, Sec. 2, Ti Ding Blvd., Taipei, Taiwan Manufacturer Golden Elite Technology (SHENZHEN) Co., Ltd. Manufacturer Address No.1 , Nan-Huan Rd., ShaJing, BaoAn, Shen zhen, China Product Type Wireless Motherboard Trade Name ECS ELITEGROUP Model Number MCT02A Frequency Range 2412 - 2462 MHz IEEE 802.11b / 802.11g 2412 - 2462 MHz IEEE 802.11n 2.4GHz Standard-20MHz 2402 - 2480 MHz Bluetooth v3.0 Transmit Power IEEE 802.11b: 0.067 W / 18.26 dBm (conducted power) IEEE 802.11g: 0.046 W / 16.64 dBm IEEE 802.11n 2.4GHz Standard-20MHz: 0.035 W / 15.39 dBm Bluetooth v3.0: 0.003 W / 5.31 dBm Antenna Specification 2.85 dBi Antenna Designation PIFA Antenna RF Evaluation 0.27 W/m 2 The above equipment was tested by A Test Lab Techno Corp. For compliance with the requirements set forth in 47 CFR § 2.1091 & 47 CFR § 1.1310. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Report Number: 1408FS11Page 3 of 7 ©2014 A Test Lab Techno Corp. 2. Human Exposure Assessment Due to the design and installation of this product, it is not possible to conduct SAR evaluation. This is because client either manufactures or supplies the antenna(s) that will be used in the installation of this product. Therefore, this product will be evaluated as a mobile device per 47 CFR §1.1310 titled “Radiofrequency radiation exposure limits”, generally referred to as MPE limits. In 47 CFR § 2.1091, paragraph (b) defines a mobile device as “a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 cm is normally maintained between the transmitter’s radiating structure(s) and the body of the user or nearby persons. ” This product is intended to be installed into a vehicle such that the unit is physically secured at one location. In the installation guide supplied with the product, Client has made the following statement: “IMPORTANT: To meet the FCC’s RF Exposure Guidelines, the antenna should be installed so there is at least 20 cm of separation between the body of the user and nearby persons and the antenna”. Based on the installation of the transceiver and the antenna, the transmitters radiating structure is more than 20 cm from the user. Thus, this product is a “mobile device” as defined in section § 2.1091 paragraph (b). Exposure evaluation Equation from page 18 of OET Bulletin 65, Edition 97-01 2 4R PG S π = Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna. Report Number: 1408FS11Page 4 of 7 ©2014 A Test Lab Techno Corp. 3. RF Output Power Band Date Rate CH Frequency (MHz) Average Conducted power (dBm) 1 2412.0 18.26 6 2437.0 18.22 1M 11 2462.0 17.90 2M 6 2437.0 18.17 5.5M 6 2437.0 18.11 IEEE 802.11b 11M 6 2437.0 18.04 1 2412.0 16.64 6 2437.0 16.40 6M 11 2462.0 16.25 9M 6 2437.0 16.35 12M 6 2437.0 16.31 18M 6 2437.0 16.23 24M 6 2437.0 16.15 36M 6 2437.0 16.11 48M 6 2437.0 16.04 IEEE 802.11g 54M 6 2437.0 15.98 1 2412.0 15.39 6 2437.0 15.32 6.5M 11 2462.0 15.13 13M 6 2437.0 15.26 19.5M 6 2437.0 15.21 26M 6 2437.0 15.16 39M 6 2437.0 15.09 52M 6 2437.0 15.01 58.5M 6 2437.0 14.96 IEEE 802.11n 20MHz 65M 6 2437.0 14.89 Report Number: 1408FS11Page 5 of 7 ©2014 A Test Lab Techno Corp. Band CH Frequency (MHz) Packet Type Average Conducted power (dBm) DH1 5.26 DH3 5.29 0 2402 DH5 5.31 DH1 5.02 DH3 5.06 39 2441 DH5 5.08 DH1 4.30 DH3 4.33 Buetooth GFSK 78 2480 DH5 4.36 DH1 2.86 DH3 2.89 0 2402 DH5 2.91 DH1 2.71 DH3 2.73 39 2441 DH5 2.75 DH1 1.84 DH3 1.86 Bluetooth π/4-DQPSK 78 2480 DH5 1.88 DH1 2.92 DH3 2.94 0 2402 DH5 2.97 DH1 2.76 DH3 2.79 39 2441 DH5 2.81 DH1 1.89 DH3 1.92 Blu…

Text truncated - open the document above for the full version.

Part 15C Test Setup Photographs Radiated Emissions Test Configuration: Below 1GHz _ Front View Below 1GHz _ Rear View A Test Lab Techno Corp. 1 of 3 Above 1GHz _ Front View Above 1GHz _ Rear View A Test Lab Techno Corp. 2 of 3 Close View A Test Lab Techno Corp. 3 of 3